HP Z240 Case Swap Guide!! Everything you need to know!!!

[@RandomBSOD]

I thought this video was better THAN your previous, but THEN I read the thumbnail 🤣

[@wobwobcycling]

Thanks! I used your idea for the USB3 cable. Bought one and stripped some of the two wires, soldered them together and wrapped them in electrical tape. No more F1 to continue! Did this for a case swap of a ProDesk 400 G2.

[@majorbelov]

You explained the power supply adapter plugs really well. I could only find 2 video that actually showed it. Thank You!!

[@DLMtechgarage]

Glad I could help

[@TheSUVAGA]

One of the best tutorials out there. brilliant. I am builing this now. For the front i/o I am just bridging the pins by solderinn a thin wire between then on the back side of the MB

[@kotasdanroda5132]

Usually i saw some builds that has an fan error but man that was cool

[@hardcorenoob2]

just finished jumping the USB 3.0 and USB 2.0 headers. I decided to solder jumpers on the back of the motherboard, i didn't dare to ruin the case I/O cables by splicing them since i want to upgrade in the future. Thank you for your explaining the headers layout since HP is very protective of their innovations (switching 2 pins and calling it proprietary )

[@matthewsteinert1002]

Depends on the optiplex series for the adaptors I have a 3010 and didn’t need any adaptors for another psu

[@TheHakoworld]

thanka lot man , i just bought 400 MBs for the same model to remarket it in my country , I knew it was possible but you made it dead sure.

[@DLMtechgarage]

awesome, they are great boards, easy to swap and run rock solid!!

[@dingchavez1960]

I put a 1245 v5 CPU in the SFF case and it was throttling like crazy (my barebones kit came with the little cooler, not the big one). Finally got all the parts today and it works so well, it was a super fun project. Still gotta figure out the chassis fan tomorrow, I think my problem is I connected my case fan to the molex connector.

[@christopherchristiaan3788]

you answered my question , even when i didnt ask hahah, great vid ready for part 2

[@DLMtechgarage]

Glad you enjoyed it, thanks for watching and part two drops Friday

[@PitFighter2007]

Any chance you can take a closer look at the pin outs on the adapter 6 PIN end?...far too many adapters out there that say are compatible with the HPZ240 and just dont work when they turn up. Knowing what pins go where would be a big help.

[@DLMtechgarage]

I just went with the ones the specifically say hpz240 and never had an issue. I would look up the pin out but I am not too good with that stuff.

[@btarg1]

That adapter is out of stock on amazon rn, and the only others I can find have bad reviews and look dodgy and cheap. Is there a way to avoid replacing the PSU?

[@DLMtechgarage]

not sure, I have always done it with the psu swap.

[@ConorMcG-i2v]

My first decent budget pc was an hpz440 workstation with 32gb ram and a xeon e5 2640 v4 for around 245 dollars. then i put in a 1650 gddr6 open box from microcenter and it only cost me like $130 without waranty. then I did a case, motherboard, and psu upgrade for like 200 dollars. i was able to put a 2080 in there and in total it was only like 600. my sister now uses the pc but it was literally the best purchase of m ylife.

[@DLMtechgarage]

Great value

[@armadanoob9330]

Great video, it helps me out a ton!!! I have the same pc but I have an i5 6500 with an M.2 SSD, you think this changes anything about the process?

[@DLMtechgarage]

the m.2 might change things only because i believe they mount different but I'm sure you can find a way to secure it but other then that everything else is that same. glad the video help and thanks for watching.

hello, excellent tutorial, I'm changing the case, and I want to know the name of the front USB adapter, please.

[@DLMtechgarage]

links and names in the description for everything i used

[@yikezwot9032]

Hi All. Would the Elitedesk 800 g1 be the same connections for USB2 and USB 3? I think I read some where it was but ???🤔🤔🤔🤔

[@DLMtechgarage]

its the same. did a video on it too. will post a link, drop a sub and check out my other case swap stuff too kzbin.info/www/bejne/kKnakGeBi5p3fq8

[@benbarbosa9207]

thank dlm tech garage hi was looking for work around for usb 3.0 and your video help allot me it on a hp prodesk 600 sff the are the same as hp z240 for my usb header i did the same but i ground my wire to the case it work to it ground

[@DLMtechgarage]

nice, yea I thought about doing that too but wanted something a little more oem looking.

[@kubocs]

Can I still use the Front Audio and mic in the front i/o after doing the jumping wire trick?

[@DLMtechgarage]

yup, everything works fine in fact the audio requires no modding what so ever. part 2 of the video shows and demonstrates everything working. will post a link below. kzbin.info/www/bejne/jJerhGWArKySbNk

[@RakeshSharma-bd5ef]

Thanks for uploading the video. I have two questions. 1. Do the SFF and Tower models have the same motherboard? 2. What is that thing at 23.20 that you are using to power on the computer? Thanks

[@DLMtechgarage]

they are slighly different, and I use a cheap button I found on amazon.

[@mikecullen6557]

Great video thankyou, Do you know if there's away of getting rid of front chassis fan not detected. I've removed the old fan there is no space in the new case

[@DLMtechgarage]

I just added a small fan plugged it in and mounted it somewhere hidden

[@zulhelmiesapiuddin3487]

i have this exact office pc , will swap it into a new case after the case arrived .. will let you guys know the progress after since i am very far from USA which is Malaysia. nice to meet you .

[@DLMtechgarage]

These are great pc's for upgrades and gaming rigs. Def let me know how the swap goes and feel free to reach out if you have any questions or need input!

[@zulhelmiesapiuddin3487]

@@DLMtechgarage bro if anyone can create 3D io shield footage (i dont know what is the name) so that everyone can 3D print the io shield will make the swap perfect !!

[@DLMtechgarage]

@@zulhelmiesapiuddin3487 I know right. Wish I knew someone who could 3d print, I would of jumped on it.

[@zulhelmiesapiuddin3487]

update : i just finish my swap case , i did not do the cut and splice for front usb 3.0 and 2.0 , the io working like normal read and write only you would see the error info during boot up.

[@DLMtechgarage]

@@zulhelmiesapiuddin3487 yea cutting and splicing is for those who don't want to deal with the error on boot up but outisde of that it works perfect .

[@maxking7]

Ottimo e utilissimo tutorial, grazie mille

[@BakedBeansYT1]

you explained this so well ima pc NOOB and im gonna do this to my Z230

[@FaizanKhan-jy6nk]

i keep getting 90e power supply fan not detected after new psu is installed. I am using the cable you suggested from amazon and Seasonic FOCUS GX-750, 750W 80+ Gold. any advice? I also updated the bios. Your video allowed me to consider doing this build. Thanks!

[@DLMtechgarage]

reading the forums, everything points to a power supply issue. forums state that the sensor is designed to detect failing power supplies, but in this case, i believe the seasonic focus if i am not mistaken has zero rpm mode which would trigger the motherboard to not detect the fan and cause an error. this technology came out later after the hp system was built. I would try plugging in the old psu just to test the theory but ultimately you would need a psu without that feature.

[@armadanoob9330]

Hi, do you know if this mobo will support an i7 7700k? everything is compatible from what I've seen but dunno

[@DLMtechgarage]

i can't confirm but the forums from hp website say yes h30434.www3.hp.com/t5/Desktop-Hardware-and-Upgrade-Questions/Upgraded-from-i5-6500-to-i7-7700-on-HP-Z240-and-now-only/td-p/7048552

[@gabrielrola5325]

Hello I ran into some error, after i swap the case of my HP Prodesk 400 G1 into new case *mATX when booting up it says Front Audio not Connected, Front USB not Connected and i had to press F1 every time pc boots up do you guys have any solutions?

[@DLMtechgarage]

not sure if the 400 is similar to the z240 but the front audio should be standard and the front usb needs to be grounded like i talked abou in the video.

[@catherinemorgan2741]

You can try using thin cardboard to make IO shield cereal box is good two-way tape or glue it to new case

[@DLMtechgarage]

interesting idea, one that I must try!!

[@alyonline1994]

عندى جهاز Z240 تم تغيير الباور ل كولر ماستر وتم استخدام تحويله 24 ل 6بن المشكله يجب فصل التحويله عند تشغيل الجهاز كل مرة تم التجربه ع اكتر من باور تم التجربه ع اكتر من وصله ولازالت المشكله هل تستطيع مساعدتى ؟؟

[@hessxpress3016]

So you still need adapters. my dell 7010 board plugged right into thermaltake PSI and the fans i just repinned the connectors. Super simple

[@DLMtechgarage]

not really. the power buttons and such just plug in but the usb require a little modding but nothing terrible.

[@bersus3725]

Hello. I have z240 board which i bought separately. I dont get it, how to turn the motherboard on? What cables did you connect to power on?

[@capostrength3908]

When you were explaining the power part at 20:40, where did you get the pins from?

[@DLMtechgarage]

Amazon

[@makedaevilmage]

7:00 Oeh I guess i could also 3d print a plastic nut, hmm. I've found so many uses already for my 3d printer in pc repairs. Like drive brackets, fan shrouds, gpu bracket and sorts of parts.

[@DLMtechgarage]

I need to get into it!

[@2011jaydog]

thank you for figuring out some of these dell n hps front psanel pins...its a pain...ive sold a few older pcs n nice to figure out the pinoit...who knows a pc like this one may ve next one I sell.

[@DLMtechgarage]

Ive been flipping these left to right cause of the price to performance and they are so much easier to case swap and mod.

[@2011jaydog]

@@DLMtechgarage yeah I can't blame you! I'm working on a 20$ hp omen..had a r5 1400 ..a 650w inland bronze..keeping n painting n modding the case..just bought son a Asus b450 n I got his gigabyte b450..16gigs oloy 3600mhz ram was like 60$ just got the red n black msi 1050ti..outta look n do good :) my cuz brought me a alienware mobo with a i5 7400 in it and may fix it up next..seen your gtx 980 or 960 vid n u was using a i5 7400 with it n looked like it did good gaming bn a lil newer than 4th gen or so Intel or even 1st gen ryzen that 7400 will outdo a few ryzen3 and 5 chips :) I'm not a hater I like both especially when free or a deal :) saves me a lil n I decide to buy parts n build it up n find a home for it :)

[@DLMtechgarage]

@@2011jaydog same here team red blue or green, don't matter cause in the end all teams will make you some cash lol..

[@nicholasdrysdale6042]

Hey u think these steps will work for the hpz420?? I want to to this with that pc and it’s my first pc build I think I can do it

[@DLMtechgarage]

not sure, mobo looks similar, and I have found hp did not change too much around that time line. def something to give a chance. the forum is where I figured out how to do the swaps along with matching pinouts from the case wiring.

[@exodus58]

Hey, did you do a video on Optiplex 7010 SFF case swap?

[@DLMtechgarage]

Yea got a how to guide that covers that series on the channel. It's the same as the 90 and 30 series optiplex. talks about the adaptors needed and the build.

[@ricardodesousa871]

Hello. Which cpu fan cooler you used because I have an old Intel CPU fan cooler from a 775 socket and it doesn't fit

[@ricardodesousa871]

I bought a cooler master fan cooler for the socket 1155 and it fits with this motherboard

[@andjamoo]

Awesome video. Ive got the Z230 that I moved into the case of another prebuilt. It powers on but I don’t get any signal on my monitor no matter which display output I use. Reset the CMOS and reconnected all of the hardware I originally took out. Any ideas?

[@DLMtechgarage]

the power cables adaptor has to be correct, many order the wrong one for the other models and have that issue. pinouts are different. link below to the exact one. www.amazon.com/YEZriler-Adapter-Sleeved-ProDesk-EliteDesk/dp/B0B2HVJZJ8/ref=sr_1_1_sspa?keywords=hp+6+pin+to+24+pin&qid=1668557691&sprefix=%2Caps%2C49&sr=8-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&psc=1

[@andjamoo]

@@DLMtechgarage thank you so much! I’ll give that one a shot and report back

[@hman6159]

@@andjamoo did it work?

[@Furuwakashi]

is this suitable for hp 600 g1 sff?

[@DLMtechgarage]

very similar

[@Furuwakashi]

@@DLMtechgarage oh when i was browsing some comments umm i see some that they tried it on their sff 600 g1 some how the usb gets shorted

[@yourboizach9681]

Does this work for all hp z-xxx computers or specifically the z240? I want to do this with the hp z440 but I'm not sure everything is the same like in the video.

[@DLMtechgarage]

so far most hp's use the same style pin out so I believe it might.

[@mikko339]

Hi, my case don't have usb3 / usb2 front panel. Do y have quide howto cheat motherboard to think that there is connection?

[@mikko339]

i think that yor video explaned that :D

[@joelbates6499]

Nice! I'd like to do this for the z420 or z620-I will keep this as helpful reference. Thanks for all the information.

[@DLMtechgarage]

Any time!

[@christianmino4073]

If you don't do any jumping stuff, you can use the front usb right? it just gives you the error? thats the whole point was to skip the errors?

[@DLMtechgarage]

it can work but I have find it to be unstable and random drop outs. but then on other case swap I had no issue.

[@christianmino4073]

@@DLMtechgarage It turns out I found a GTX 750 low profile from my friend for 15 bucks so I’m gonna throw that in there not do it Kay swap and do it at the super low price of 225. I’m going to test it and make sure you really can get 60 frames on your esports gaming if you can I’m gonna sell it to somebody who really needs a cheap computer, or my dad’s friend who wants a workstation for basic web design. I have somewhere I can get these computers but 500 GB hard drives, and 16 GB of RAM for about 70 to 80 bucks with shipping so I’m gonna be doing Kay swaps on these a lot. Can’t beat 6th gen Intel for 100$ (with a sata ssd) And I already have hard drives, so I can throw some of those in there so it’s not only a 500 GB bill

[@christianmino4073]

@@DLMtechgarage Also, damn bro I just realize this was you yo, much love bro I love your videos dude love them so much seriously you’ve helped me make so much money and you helped so many young kids around the world get Fortnite started. Thank you so much bro, I personally play on the GTX 1080 TI Alder Lake build, but it’s still nice to do these flips and make some money. It’s my only job right now you literally help me put food on the table.

[@christianmino4073]

@@DLMtechgarage So, thank you so much, bro for reaching out, for answering, and for making your videos, you are the MAN. Also you from the northeast/east?

[@DLMtechgarage]

@@christianmino4073 NC

[@kotasdanroda5132]

I have a HP compaq 8100 sff and im planning change the psu to a generic 700w and recase it into a bigger case. And now im worried if it is safe 😅

[@DLMtechgarage]

it's safe as long as your take your time, take pics of all your cables, make sure you are not stically charged and never force anything. never done the swap so i would recomming tracing your pwr button and leds and see if you can match the connectors for the different case.

[@9speedgaming901]

great video! my problem : i have the exact same z240 and put it in the coolmaster 500 mesh case . everthing is working the fans the leds everything . but there is symply no signal to the monitor . do you think something is broken?

[@9speedgaming901]

could it be the power adapter . that it has not enough watt ? would be very cool to get an answer . thank you

[@DLMtechgarage]

what kind of graphics card are you using?

[@DLMtechgarage]

what kind of graphics card are you using?

[@9speedgaming901]

@@DLMtechgarage hey thanks for the answer. i bought this pc about 5 years ago from a company it has an intel i7 7th generation but i dont know the graphics card. they said to me that they‘ve installed a very strong and good nvidia card

[@DLMtechgarage]

@@9speedgaming901 I would try removing the graphics card and plugging the monitor into the board. That would rule out a graphics card issue. Then if you still have the problem try each ram stick 1 by 1 in the first slot to rule out a memory issue. Another thing to consider is checking the psu connections. are the 24 pins and 6 pins attached properly. I have seen people plug the pcie into the cpu 6 pin by mistake. if all that checks out, then look into the adaptor you bought. The adaptor is specific for the z240. Their are ones out their that look identical and will plug in but are wired differently. I ran into that.

[@JimParkinson-l4g]

i have got two z240 1 tower and 1 sffi can only get the tower to oot with the psu adapter the one in the sff green light goes on but wont boot but works with its own powe supply which i cant use in this case any help would be nice thanks

[@38cards]

Hey mate, do you know what pins I would have to jump for the front audio?

[@DLMtechgarage]

i can't remember but I don't think i have to jump anything.

[@38cards]

​@@DLMtechgarage the case I'm using is pre old so it doesn't have a modern front panel audio connector 😂 any ideas?

[@matteofeyaerts]

in my z240 there's a 400w platinum psu

[@kaiserhades666]

Hi, guys!!! Nice guide. I have a HP 600G2 SFF and followed all steps, I'm able to skip the USB2 and 3 errors, CH FAN and PSU FAN....but, when I plug any device on my frontal USB, the OS informs Unknow USB Device....My case have just 1 USB2.0 and 1 USB 3.0 in the front panel. for the USB2, my MB have 12pins instead of 10, I had cut the GND and made a jumper between pins 8 and 12. For the USB3, I had cut the pins 01 and 04 of the extensor cable and merge the fours pieces of cable... Could you help me? If I made a mistake, let me know.

[@DLMtechgarage]

not sure, never ran into that issue. seems like a ground issue somewhere or maybe a shorted usb

[@kaiserhades666]

@@DLMtechgarage I checked again, trying to rebuild the "adapters" now, at least the USB2 is working...but the 3.0 still the same way...

[@kubocs]

Does this on the z230?

[@DLMtechgarage]

not sure.

[@richardbennett6539]

Ace video as always - is there an Xeon variant that works with this gneration of intel socket please?

[@richardbennett6539]

ahh just spotted the part 2 video :)

[@DLMtechgarage]

Intel Xeon E3-1240 V3 is what I run in mine, I use it paired with a lp 1650 as a HTPC

[@alfi0s]

What was the original CPU that came with that machine? I was wondering if I should go for HP Z240 Workstation SFF Barebone 6th Gen Intel Xeon Motherboard *No CPU/RAM/SDD and add the e3 1245 myself cause they're very hard to come by pre-assembled. Barebones is like $36, with a 1245 is like $200

[@DLMtechgarage]

I tend to go with the barebones as it can be cheaper if you find the right price for the other parts.

[@dingchavez1960]

Hey, dunno if you're still interested in this but I just finished building everything with a 1245 v5. Runs snappy, no surprises.

[@guitarandbeyondplus]

I've done this PS mod to a HP elite 8200 and a Z240 with a 575W PS but when I try a new 650W AZZA PS it works on the 8200 but does not power on on the Z240. Same 24pin to 4 pin cable. The Z240 sill works with another ATX 575W PS. Any clue?

[@DLMtechgarage]

z240 is pinned differently and specific, I have found that if you don't have that adaptor the psu's won't work with her wattage psu's

[@danielsalcido4930]

So the 3.0 usb you Just put 1 and 4 pin together?

[@DLMtechgarage]

yup!

[@sacredbeats5080]

I did a case swap on one of these. I get a black screen when trying to boot from a graphics card. I was able to boot into windows with the on board video and installed the graphics drivers. Still black screen when plugged into video card. Card works as I’ve tested on another machine. Tried different cables and different ports. Any ideas? Thanks.

[@DLMtechgarage]

might need a bios update, these model where finacy with newer cards and I know the newer bios has some codes for them.

[@hakimmajid5935]

Can i just re use usb from old casing.. then no need change any wiring except for on off swicth n power supply.. tq

[@DLMtechgarage]

you can if you can find a place to mount them in the new case. I have use to do that.

[@hakimmajid5935]

Tq bro

[@BayanNiJuan1972]

hey man can i apply the usb setup to HP Compaq 6200 Pro case swap?

[@DLMtechgarage]

not sure

[@tbrun1000]

does the Z240 have the option for "Above 4G Decoding" in the bios?

[@DLMtechgarage]

not sure, will have to look next time I get one in. doubt it as the bios is real basic

[@felixyep6551]

Hi, great video thank u for do it, I want to do the same on hp prodesk 600 g2 sff, but, the pins of the yellow connector are different, how do I find out which one I have to jump ?? (pin 7 and 8 is blank) and the rest of pin (1-6 / 9-10) not

[@DLMtechgarage]

never tried tinkering with one of those. I just follow the pins to their respective buttons and leds, draw a diagram and make my own pin outs.

[@felixyep6551]

@@DLMtechgarage hi, thanks for answer, i have update: on the hp prodesk 600g2 the usb conector have 12 pins not 10 pins; 1-2 pin (power +v5), 3-4 pin (d-) 5-6 pin (d+) , 7-8 pin (ground), 9-10 pin (blank), 11-12 (????unknow), i tried (with a lot of fear...) jump the 8 pin with the 12 pin and works!!!! not error during post!!!, the 3.0usb work like u show on the video!!!

[@DLMtechgarage]

@@felixyep6551interesting so it's kind of like the z240 where the extra pin is a signal ground for the error. Nice!!

[@kaiserhades666]

@@felixyep6551 How are you doing? I follow this same way, but my OS reports Unknown USB device...do you know how to fix it?

[@kubocs]

Hey, how did you figure out where the front panel connectors go?

[@DLMtechgarage]

I looked at the original case pin out outs and traced them and followed them to match.

[@kubocs]

@@DLMtechgarage ah i see thanks

[@kubocs]

@@DLMtechgarage Thanks dude. I managed to get my power buttn and the leds to work by doing what u did.

[@DLMtechgarage]

@@kubocs awesomeness

[@Khadjs1804]

Do you have a link for pin assignments for HP Prodesk 600 G4?

[@DLMtechgarage]

I don't, haven't seen one yet.

[@crlundberg]

@dlmtechgarage is this the same for the elite desk g4?

[@DLMtechgarage]

not sure, never messed with one.

[@ThatGuyOG_Rust]

Youz could change that low pro plate fyi.

[@stanisawszczypua9076]

Hi I have problem with Z230 sff case swap. After conneting everything I couldn't get the mb to actually start. Power led would blink and that's it. No fans spinning nothing. Green led on mb is on so I think the power adapter I bought is good. Any thoughts? 🥺

[@DLMtechgarage]

I have seen that happen with the wrong adaptor, has to be z230 specific, people tend to get the 240 and other models by mistake. looks similar but wiring is different. www.amazon.com/COMeap-Power-Adapter-Workstation-12-inch/dp/B06XW7RWNH/ref=sr_1_2?crid=1FVVN67J3FFMC&keywords=hp+z230+24+pin+to+6+pin&qid=1675806217&sprefix=hp+z230+24+pin+to+6+pin%2Caps%2C65&sr=8-2

[@stanisawszczypua9076]

@@DLMtechgarage The one I bought was labeled for Z220/Z230 and looked identical. I already send back adapter and that Z230 😟 thx for answere though

[@antoniosantagata5340]

How about the hp pavilon tp01 will it works?

[@DLMtechgarage]

not sure. if the mobos are the same I would say yes.

[@littlechief3739]

do you know if this will work with the hp z230 Tower?

[@DLMtechgarage]

not sure as it's a different chipset and not sure if hp kepts the same layout for the inputs.

[@blade8424]

I wish I can put a Cooler Master fan on mine. :(

[@TheRawChuck]

Hi, is there a way to tell BIOS to ignore all errors except keyboard?

[@DLMtechgarage]

nope, it's really limited, and if they did that then people would be case swapping this easier.

[@TheRawChuck]

@@DLMtechgarage Good point.

[@DatLe-zl4ck]

Can you make a video on the Hp elitedesk 800 g1?

[@DLMtechgarage]

if i get one in the garage most def will!!

[@mypfpiswhatourphonesees4294]

i have the elitedesk 800 g1 and its really similar to this test. Just copy what he does and it should work.

[@tonyavila7200]

Dude the link for the adapter is wrong! For those that are trying to do the same swap you need one that says z220 or z230 the one on Amazon that specifies z240 is the wrong adapter only the z220/z230 works on the green motherboard. Believe me I tried for 2 weeks to fix this issue until I tried a z220 adapter and now I don't have the 90e power supply fan not detected error. I hope this helps others like me. And please fix the link!

[@DLMtechgarage]

Thanks. link has been updated, never realize i used the wrong like!! much appreciated!!

[@ebaylover24]

could the same be done with the z230 sff?

[@DLMtechgarage]

not sure as its a different chipset but I have found in my experience is that mobo manufactures tend to do things the same, so the front panel might be similar and the pinouts might be similar.

[@vikdor6345]

Can i do the same thing on my z240 that is bigger than youra

[@DLMtechgarage]

yes. the matx z240 you def can and have more options. you can upgrade the psu and get a better graphics card for it.

[@nasneo2852]

hey, does this method work on with HP 600 G1 sff?

[@DLMtechgarage]

not sure. never missed with none.

[@vk6996]

any chance you know what it means when cpu fan keeps cycling every few seconds and the green light by the power button blinking green?

[@DLMtechgarage]

not sure but sometimes reseating the memory stick fixes weird errors like that.

[@johncollins5552]

My hp does that and the problem only ends when I run the pc with one single stick of ram, I suspect a bios or Windows update has messed with the dual Chanel ram controller somehow?

[@Furuwakashi]

upload a video for sff 600 g1 please

[@DLMtechgarage]

very similar to the 800 g1 video i did. Only main difference is making sure have the correct power adaptor for the swap

[@Furuwakashi]

@@DLMtechgarage btw u have discord?

[@DLMtechgarage]

I don't, get asked that alot, prbly need to start one.@@Furuwakashi

[@Furuwakashi]

@@DLMtechgarage if you do make one let me know thank you

[@Furuwakashi]

@@DLMtechgarage yoo update i just build my pc and everything is working fine no errors i did not use any bypass like yours what i did is i also transfer the usb front ports to another case i want to show it to you but i don't know how

[@ricardodesousa871]

I have a problem with the front io usb 2.0 conector. I have an hp elite desk 800 g2 sff and the usb conector has 12 pin its different to the one showed in the video. Could you tell me which pins i have to jump?

[@DLMtechgarage]

I think I have a specific video on that.

[@Skyesheild08]

I got my z240 for 20dollers au at the tip shop and it works and plays games fr well

[@RhythmStudio.26]

Great video.. Thank you 😊

[@DLMtechgarage]

Thanks for watching!

[@ogsgamer1]

em about the psu fan not dedected in hp 800 g1

[@DLMtechgarage]

if you did the swap, did you get the correct adaptor, the adaptors are particular based on the model. has to say 800g1. got a video on the 800g1 swap

[@ogsgamer1]

@@DLMtechgarage i did not swap i just plug in new psu and added rx 570 cause original hp case is fine for me

[@henrytom5824]

This is sick dude.

[@DLMtechgarage]

Thanks!

[@wambz5660]

Does this work with the elite desk 800g1

[@DLMtechgarage]

i'm actually working on that. got some of those in and see alot of similarities. hoping to have a video on the swap guide in a few weeks

[@wambz5660]

@@DLMtechgarage thank you!

[@mikesgarage394]

Your p/s adapter link is for a wrong one.

[@Duncan-Donuts]

the 70 series optiplexes are way better then the 90 series ones because of the newer cpu's and cheapness of them and the m.2 support

[@ThatGuyOG_Rust]

Thanks for sharing man! I wish I found this earlier... I have done the same thing. I think the most PIA was finding the power pinout that was not ass backward on the Google... Check your email as I got some questions for you!

[@DLMtechgarage]

will do.

[@andrewbeardsworth5461]

Awesome mate

[@DLMtechgarage]

Thank you! Cheers!

[@facelessvaper]

Intro👍keep it simple👌

[@paulsbunyans]

Bought my Z240 without CPU or Ram for $10 oh and the LANDZO cables are no longer available

[@DLMtechgarage]

other brands make them too.

[@JimNichols]

Easier "then"?

[@DLMtechgarage]

the optiplx

[@simonyeong756]

Awesome

[@DLMtechgarage]

Thanks!

[@PanGames]

Nice video 🤠

[@DLMtechgarage]

Thanks 😁

[@Hua_Sa]

Can you case swap with hpz230

[@DLMtechgarage]

yup!

[@Hua_Sa]

@@DLMtechgarage are they the same steps as this video, i want to case swap with my hpz230 but im afraid i might mess something up

[@DLMtechgarage]

@@Hua_Sa should be, looks the same. cant really mess it up.

[@johncollins5552]

I like jumpers.....

[@josefhunne5500]

OMG ... a waterfall of words covering usefull informations ...

[@Kermit306TCI]

the more beautiful way of connecting these pins, is soldering the right pins together at the back of your mainboard, instead of these ugly connections inside the case. And it saves money on buying this $10 cables

[@BLLHacks]

I just don’t understand why you didn’t use your soldering iron 😁

[@DLMtechgarage]

watch the intro to the below video and you will see why lol..... plus mine was broken at the time... kzbin.info/www/bejne/qqScepengbacbsk

[@BLLHacks]

@@DLMtechgarage I was totally saying that tongue and cheek I think you said 16 times in the video your soldering arm was broken,, I own a computer store in Tampa and I'm fairly certain we have an extra hakko soldering iron we're not using. If I can find it and you're still in need of one let me know and I will happily send it to you for free., my company is performance computer group in Tampa Florida. I am We have a Facebook page feel free to message me there if you want to take me up on my offer

[@DLMtechgarage]

@@BLLHacks man that would be awesome, i buy the cheap harbor freight ones, or amazon special and they break. I never know whats good to get for soldering so just go with what i find lol.. def will shoot you a message on the old Facebook. Im from NC and frequent the tampa florida alot in the winter. Def will have to come visit!

[@benbarbosa9207]

if you want skip the (rear fan error) loop a wire on the front panel header on the pin next to power switch and the pin next to the blank the last pin stay loose or nothing on it or empty just to be sure you guy understand my poor english

[@DLMtechgarage]

i gotcha def a good idea.

[@DLMtechgarage]

@@koomei2 get a fan hub that either sata or pwm powered. ive used this one. link below. www.amazon.com/ID-COOLING-Powered-Splitter-Computer-Internal/dp/B08BFJZWGM/ref=sr_1_11?dchild=1&keywords=sata+fan+hub&qid=1630864206&sr=8-11

[@ThatGuyOG_Rust]

At the Amazon... LMFAO

[@EF-by1kp]

Lmao i want do this but my dad want i upgrade z240 but want keep in same case so i just need change memory upgrade ram and change cpu

[@AccessCode101]

I just call the guy.

[@henrytom5824]

Sff ?

[@DLMtechgarage]

Yup! Part 2 where I do the build comes out friday!

[@christopherjames9843]

I strongly hate proprietary garbage.