I purchased the D8860 last year, and thankfully it doesn't have the disastrous quick disconnect Fein chuck shown here and went with a standard Weldon chuck.
@jimh129411 ай бұрын
Great Video! Major take aways for me were 1) your demonstration of the quick connect feature. In another videw - they were "fighting againts" the connecter - where you simply inserted the piece. 2) Your idenfication and lick for the "AccuSize Nitto Annular Cutter 10pc Set" which fits this model is also very helpful 3) Lastly, your identification of the Nitto to 3/4 Weldon Adapter by name is a big deal great find too! FYI - One thing that helped sway toward the Vevor 1400W Mag drill - was the ability to adjust - raise and lower the arbor height by lossening the silver hex score. This to me makes it much more feasible to use the drill chuck and / or other adapters. Once again thank you.
@ChallengeTheBuild11 ай бұрын
Thanks for taking the time to watch and comment, I appreciate the positive feedback. 👍
@melgross9 ай бұрын
I use annular cutters on my mill. The R-8 to 3/4” Weldon annular adapter chuck I use can accept the Nitto cutters. You have to rotate them to get the set screws to line up, but it does work without a problem. But as he said, the Weldon shank bits don’t work in the Nitto chuck. I assume there’s a Weldon to Nitto adapter available as well, but I haven’t looked yet.
@ChallengeTheBuild9 ай бұрын
Appreciate your input and thanks for watching..👍
@davehammond97965 ай бұрын
I own the same unit, if you use the Nitto one touch to Weldon adapter you must increase the length of the guide pin equal to the increased offset of the adapter.
@ChallengeTheBuild5 ай бұрын
This is great info, I didn't think of that. I appreciate you adding value to this video. With that said, what's your overall opinion on the mag drill? Would you recommend it?
@dollabillbrunson8107 Жыл бұрын
Thanks for the explanation!
@ChallengeTheBuild Жыл бұрын
You are welcome...Thanks for watching and commenting 👍
@ChallengeTheBuild10 ай бұрын
I don't believe it does..
@edanhellmann13 ай бұрын
Thanks for the review. Judging by sound alone - It sounds as if the minmal speed possible is still very high for cutting metal. Is that your impression as well?
@ChallengeTheBuild3 ай бұрын
It definitely has the torque needed to cut metal at a low rpm this also cuts down on heat transfer into the cutter which allows longer cutter life...(using coolant of some kind of course)
@MorninWoodie Жыл бұрын
Where do you get the adapter for the Weldon cutters?
@ChallengeTheBuild Жыл бұрын
I see my link in the description says currently unavailable on Amazon, you may have to search online. You can try this part number ( Accusize 0519-8000 ) see what happens.
@MorninWoodie Жыл бұрын
I got it ordered Thank you!
@gone1438 Жыл бұрын
what cutting fluid do you use and do you dilute it at all?
@ChallengeTheBuild Жыл бұрын
For this video I used wd40, other times I have used windshield washer fluid and my buddy told me years ago antifreeze makes the best cutting fluid (which makes sense) but still never tried it. I have also read the reviews on Slugger cutting fluid seems decent ( amzn.to/47bvLvv The link is an affiliate link and I earn from qualified purchases. ) Hope this helps, good luck and thanks for commenting.
@danielbuck8 ай бұрын
and now there's coolant on, and below your welding table :-\ I hate using coolant unless it's on a machine/surface that is designed to work with flood coolant. I'd rather just use a little but of cutting oil here so that coolant doesn't go all over everything.
@ChallengeTheBuild8 ай бұрын
I generally use cutting oil also, I used coolant to show the drill in use... But I agree to what you are saying...👍
@chriskuykendall39629 ай бұрын
My boy used water as coolant? 😮😂
@ChallengeTheBuild9 ай бұрын
I'd be a little concerned with rust.. A buddy of mine uses antifreeze and when you think about the properties of antifreeze it makes a lot of sense to use it... I just haven't done it yet.
@fredscheerle75926 ай бұрын
@@ChallengeTheBuild Might try it out, have plenty left over in jugs, so might try so out!
@ericayers569010 ай бұрын
Nameplate says “fried dough twist drill”
@ChallengeTheBuild10 ай бұрын
Interesting, I completely missed that... Who doesn't like a good fried twist drill...😂😂
@prietjepruck9 ай бұрын
Thanks for the review. I think the one-touch Nitto is a terrible design choice. It enormously restricts your choice of cutters and makes them significantly more expensive.
@ChallengeTheBuild9 ай бұрын
The nitto one touch is nice and they make and adapter if need be... Guess it all depends on what you need... Thankfully there are other options...
@sergioaperalta9 ай бұрын
can you make a hole in the head of a hammer?
@ChallengeTheBuild8 ай бұрын
I would have to try..
@sergioaperalta8 ай бұрын
@@ChallengeTheBuild thank you sir
@NoName-ml5yk7 ай бұрын
I don't trust paid promotions.
@ChallengeTheBuild7 ай бұрын
This wasn't paid... All I got was a free mag drill... I do not accept any additional payments for any of my product reviews, this way here my reviews stay neutral.
@ChallengeTheBuild7 ай бұрын
In my opinion you will not find any better review channel. One word to sum up my reviews and this channel is Integrity, and if you look, I respond to 99% of my comments. Nothing to hide here...
@OFFICIALUND5 ай бұрын
@@ChallengeTheBuildLOL, “In my opinion, I am the best!!!” lol. Getting a $350-450 tool is getting paid. I’m a consummate tool review watcher. You are not the best….frankly not even close. Use that not as something to tear you down, but to improve on a mediocre content presentation.
@ChallengeTheBuild5 ай бұрын
@OFFICIALUND Thanks.... I guess..... For being such a consummate tool review watcher, I would have thought the commenting skill would be better... Now don't take this as something to tear you down but a way to improve on your mediocre presentation..
@mnblkjh67575 ай бұрын
or Chinese tools👎☹️
@pagangardener2 ай бұрын
I suppose if you got it for nothing the review my lean one way
@ChallengeTheBuild2 ай бұрын
It could... But considering I bought the older model that I compared it to I am somewhat invested regardless. The new version is very nice and much better than the old one. The only thing I would suggest is getting the one with the standard 3/4 weldon shank...