Husqvarna 435 chainsaw, tear down and rebuild

[@p.chuckmoralesesquire3965]

Hey boss just wanted to say thanks for the video from 2023 :)

[@tvs3497]

I just put a brand new trigger on mine. Just one screw, a pin, and pry the plastic apart a little. I'm glad I didn't have to take it all apart. I like the saw. It's light and does what I need. It has the anti-vibration bar and that's nice. I put an 18" Oregon bar on mine and a super-fast chain.

[@bp4682]

Ruined your video with music when should have been comentary .

[@monesjason]

i dig the music

[@stevenher7711]

After rebuilt is very hard to pull the strings,take spark plugs out is easy to pull over, is there something wrong with it in this case need help?

[@Senna-xi1gr]

Cheers, I have this saw so thanks for video & great tunes. 👍🇬🇧

[@billyhelton8230]

@jef4130 What kit did you use on this? Are they all the same? Just want to make sure I get a good kit. I don't want to do it over.

[@denisgamache4642]

Thank's a lot for this video. Very informative. I will use it as a reference since I own the same saw and do my own repairs. I also own a Jonsered CS2152C and even if it's a lot more powerful, I end up using my 435 most of the time because it's so light weight and agile. And pretty good music btw.

[@gunsnsails]

Reviving the video. I took the cover off the chain arm on the R side. There's a circular spring that gave me issues that goes around the chain drive. Now I can't get the cover back on. Is this normal? I ask because it looked like yours just fell right into place.

[@steveanderson8081]

own this exact saw, great help! thanks

[@joaocarlosdallelaste6332]

Olá! Obrigado pelo vídeo muito bom mas uma pergunta porque não aceita regulagem está difícil

[@stjepansuman]

seems like brand new chainsaw

[@jimbojones2457]

Great video mate thanks a lot! I have the same chainsaw and i need to remove the carby as it's flooding. It sat for about a year with old fuel in it so it's a good guess the carby is blocked and needs a rebuild. Thanks again mate!!

[@WarlockCore]

I have the same model, changed the spark plug, fresh fluids, filter clean, won't turnover, any ideas as to what I should check

[@jef4130]

Does is have good compression? Does it have spark?

[@WarlockCore]

@@jef4130 , thanks for replying, well it's a brand new spark plug as for compression, I would not know how to check that

[@dejan9713]

Do you prefer to change piston with piston ring ? Did you try to change only the ring on the old piston? What is your opinion?

[@jef4130]

The original parts were damaged and the OE kit came with a new ring so I used it. The kits are fairly cheap so at the price point it would be stepping over dollars to save dimes if a new ring wasn't purchased and installed. My opinion... LOTR movies were lame.

[@astrogypsy]

effin' thanks for that vid man! Totally saved my day/wallet.

[@mandyssanchez2401]

What is wrong with your chainsaw?

[@jsof2]

What could have been a good video was made unwatchable by the constant music - even silence with the odd comment would have been preferable.

[@yannickcourteau2119]

I'm having trouble with mine. It starts, idle, then die. Spark plug seems good and doing fire. Could it be a bad coil or carburetor problem?

[@dustinearley5769]

Had the same problem, When you use gasoline with ethenol it will gum up the carb. To fix it i got a carb rebuild kit and i have not used gas with ethenol in any of my small power equipment for over three years and no carb issues on anything.

[@henryallen6599]

Yannick Courteau, I’m no expert but my weed eater did that a lot. I found that if you give it full throttle while and after starting and then let it idle it will stay running

[@fireman4426]

Old comment but for new ppl reading it could also need a carb adjustment or like the one guy said full throttle about 30secs to get it to warm up. I am worried about a cold seizure so i just rev mine a few times for a few secs. if it starts acting up like that. If you ever get a new carb its going to be most likely an adjustment.

[@dejan9713]

How long you wait after aplication of permatex ,to rejoin cylynder and crankcase?

[@jef4130]

I think it was maybe 45 to 60 minutes from when I applied the sealant to firing up the engine. I only ran the engine for maybe 10 seconds then didn't use the saw until the following day. From the Permatex website on the Ultra Black, "Silicone dries in 1 hour, and fully cures in 24 hours, at 70˚F - 50% relative humidity. Allow more time in cold weather." Saw is still going strong, fires right up. I just applied the sealant, thinned it out and apply, so no real wait times there.

[@jamesroach1630]

Would have been ok with out the music.

[@stephenfresh1754]

Did you just make this video because you wanted people to know that you know how to take apart your chainsaw? You don't say anything about sizes of anything location... fully informative 😆

[@jezhankinson]

OMG, As we say to the kids..'use your words!'

[@mikeoverbey]

That’s not a rebuild. You didn’t even change bearings or crankcase seals while you were there. I don’t know exactly why you were doing all of this and didn’t do those two important things.

[@markmelton8919]

A lot of times you get a tiny air leak between the 2 case halves. Where he used the Ultra Black RTV fixes the air leak. This causes worse running problems than a carb that's adjusted wrong. I've had 2 Husqvarna chainsaws do this and this fixed both of them

[@suzanemartin8242]

Kill the music and explain what your doing with close up.

[@annvanderburg3231]

how do you rewind rope

[@Stanek60]

Po co ta głupia muzyka

[@nerminhodzic2220]

grat video with great song ;

[@jonastopfreitas1682]

Parabéns...

[@kevinwright7617]

Do not try this at home kiddies on daddies chainsaw without adult supervision.

[@mikeg4247]

focus would have been nice

[@MessyKrieg]

Saw busted after two weeks. Oiy