Husqvarna 435 Chainsaw: Tearing Apart & Rebuilding Carburetor

Thank you for watching! If you enjoyed the video, or found it useful, feel free to like the video and subscribe for more content! I recently launched my merchandise shop! The quality of the merchandise is great and the designs look amazing! Feel free to check them out! All support is greatly appreciated :)
L&M Store Link: landmrepair.my...

[@glennryan4889]

Thanks for the good video Mark. This saw is also marketed (here in Spain at least) as a McCulloch CS410 Elite. It's identical, made by Husqvarna and the Husqvarna part numbers all fit it. I had a fuel leak and when I took the carb off, it had the same leak as this one from the corner of the base plate. One of the four screws had worked loose, I cleaned everything up, tightened the screws and no more fuel leak. Sometimes it's just something simple.

[@samnicholas434]

Good morning, I watched your video on how to rebuild a Husqvarna carburetor. He was very thorough. It helped me out a lot.😊

[@lmsmallenginerepair4471]

Glad I could help!!

[@Delroyss1]

Thanks, you were a big help on the 435 huskavarna carb rebuild.

[@lmsmallenginerepair4471]

Glad I could help!

[@Warf_459]

Finally. The exact video that i needed. I have that Husq varna 435 and I let it sat up with gas in it. It is my first chainsaw and nobody told me. I also didn't know it needed a gas oil mix.

[@erniepenny221]

Thanks Mark, very helpful, regards from N.Z

[@lmsmallenginerepair4471]

Glad it was helpful!

[@daithiodalaigh8914]

Thanks Mark Great vid. Very straight forward. Just learning ta use a chainsaw, husky435. Watching many vids and learnin. Keep up that relaxed style of yours.

[@giannigrigolo5550]

In Italiano?

[@roberttaggart5757]

I have the same saw and when i give it full gas it bog’s then rev’s and does the same , is it a carb issue , great video

[@rjzlwop3153]

Is it better to drain the gas and oil out of the chainsaw before storing it? And how do you run the excess out of the carburetor so it doesn’t sit? Fantastic video way above my pay grade.

[@lmsmallenginerepair4471]

yes it is drain gas, start it up and it will fun the gas out of the line and carb

[@jonlambshead5115]

Another Good Video , Thankyou.. Merry Christmas To You & All Your Family From Australia

[@lmsmallenginerepair4471]

Happy Holidays!! Thanks for watching my channel!! :)

[@hecticgerva1192]

If I dont use my saws for a while, I run em for least 5 to 10 mins once a week to prevent this. I got told to do this by my Pa and he never had issues at all and he was right.

[@loborobertson7212]

👍👍🤠

[@dalemullen96]

At 12:52, isn't the gasket placed in the wrong orientation? Shouldn't the gasket be rotated 180 degrees before assembling? Otherwise, the openings in the gasket do not properly align with the the venturis in the carburetor. Have I mistaken something here?

[@shaffersmallengineshop5957]

Horrible carb design, way too complex design. The little plastic piece holding the throttle linkage is a hidden nightamre. attaching kill wires can take an hour. POS design. great video.

[@beplh5242]

Why does the carb have 2 butterfly vales / air intakes?

[@w.e.smithereens8178]

It's called ethanol is what gums up your carburetor

[@user-xt5pm4cu6t]

i’m trying to find the carburetor adjustment tool needed for my t435 i read it was a 21 tooth splined tool but i bought one and it just spins. what do i do?

[@trjb1767]

Is it a torx fitting?

[@lmsmallenginerepair4471]

you can buy a complete set of adjustment tools from walbro or zama

[@kelseykuhn374]

I have a 435 Husqvarna chainsaw and it's only 2 weeks old and they will not take it back so I am stuck with it

[@lmsmallenginerepair4471]

why won't they take it back

[@trjb1767]

These 435s flood very easily