I Built An AWESOME 4 Link Suspension FROM SCRATCH!!

[@SUMMIT_MAN_VAN]

You would make a great Engineer Austin. I love how everything you do is measured and meticulously accounted for before installing. Keep up the great work, this build is amazing work!

[@AntonioClaudioMichael]

Nice custom 4 link design love how you used Pvc Tubing to test Flex and To make sure you got the right measurments for the custom metal Tube 4 link 12:27

[@AntonioClaudioMichael]

Gotta love the old school CAD work Cardboard Assisted Design With the New CAD work from the computer to the plasma table

[@kasunchathuranga660]

This is a whole new stuff. Abosaloutly love this content.

[@AntonioClaudioMichael]

Great video as always Austin 👍 👌

[@stevenmwalilino3001]

From Africa malawi, your stuff is so exciting to watch and very educative

[@AntonioClaudioMichael]

Nice sterling 10.5 1ton Ford axle and a Dana 60 In The front Niceee

[@waddlescustom4637]

Enjoy watching your process. Great work.

[@jeffb2456]

Beautiful work!

[@senorspiegel]

I bet you can't imagine your life without that plasma table now haha, awesome work

[@210Rocket]

I love your work and especially the FJ. This is a dream build. Your skills are exceptional. You use the pvc pipe to prototype, great idea. Have you considered using lazer cut acrylic glass to prototype your custom joints or thin metal depending on application?

[@CTMadModz]

I have them double cardan joints on the front a rear drivelines of my highly lifted Samurai, and I have drive 65mph down the highway in the winter in 4x4 and I have zero vibrations. Awesome video dude

[@walterphillips9950]

Sweet dude! And I like your background music selection. Classy!

[@MonkeyWithAWrench]

Fantastic job so far. that rear driveshaft is going to be a headache still... It was on my samurai. When you toss the limit straps on it, do three. One center to limit drive shaft angle while allowing each side to droop, then one on each side to protect the coilover. Its looking like this will be a VERY capable rig. Looking forward to the cage and bumpers!

[@AntonioClaudioMichael]

Nice CAD work

[@lachlanvandermeer1971]

Wow, just wow. You’ve gained another sub! Your work is amazing and the video is really enjoyable to watch ❤

[@mikeingalsbee2959]

Your brackets are very nice, but I'm curious why you don't use tab and slot to self-fixture the pieces for welding.

[@eddss123]

Just came across your channel, super clean work. You make it look easy. Thanks for the videos

[@mikevickers1122]

Awesome build and great fabrication skills my man!

[@BigBrownie96]

cant wait for the body work and paint, Keep up with the good work!

[@richardricafrente6620]

I love what you do, I always look forward to watch your videos

[@Mohawk.Mechanic]

I think you mentioned this in one of your videos but i cant find it... What laser level are you using?

[@oneshotpete6.591]

been looking forward to this vid … Thanks brother !!

[@scottadvevture2022]

really nice setup looks strong thanks for sharing

[@fernandopasini6350]

Toyota should sponsor you! I love your channel ❤️ watching from Brazil 🇧🇷🇧🇷

[@mahdialsenussi3066]

Nice work 👍

[@GarageFab]

Well done my man. 👏

[@phxamigo]

Where did you learn your fabrication skills????? Use to work at a garage or shop?? I love the way you take your time and do it right!! Wish I had a fab shop near me with your skills! Great work like always! 👍🏼

[@RampJD75]

Can't wait to see completely Mount

[@NavinSingh-bf2op]

Nice work man

[@2012DIY]

Excellent work 👏

[@norcoredneck]

Hey I watched a KZbin video where a guy showed certain year Sterlings came with a E-Locker. His video went through installing it in a housing that was non E-Locker. Might look it up. You do some awesome work. Gotta love that Free Govt. issue CAD supplies. 😂

[@norcoredneck]

kzbin.info/www/bejne/laWaq5eHpbSkea8

[@mondoworks9824]

What version of the 4 link calculator are you using?

[@jackburton8124]

To get the best hole with plasma is to cut small and drill to size you need. I do this but destroy my drill bits because of the hardening the plasma does. I cut fairly close to size hole I want. So my question is how much smaller are you cutting your plasma holes vs hole size you want?

[@austinniemela]

For the .75 hole I cut .65 and drilling is fast and painless!!

[@Allfather88]

What are your thoughts on frenching the center bracket into the frame to not have anything hanging below the frame?

[@austinniemela]

They are on that location for correct geometry!

[@Niko-iw1sr]

Why does your drill press always wobble around so much like that? 4:04

[@rogerjohnson3392]

That bothers me a little also.

[@JohnSmith-wb6kq]

Howzit bud, have you had any oil starv probs with the pinion bearings?

[@MG-sg2ci]

"We did it", proceeds to cut all brackets off and start over. Nice job btw.

[@pistols10]

Where can I download that 4 link calculator version?

[@MarcoSilva-x9y]

❤ top work

[@snowking171]

Question.. when you design your drawings in fusion why do you always drill your bolt holes by hand? Is your plasma not accurate enough to cut out the correct hole size?

[@austinniemela]

Yes I usually cut a small hole and drill by hand after! Plasma cuts with a little taper and I like a nice straight hole!

[@snowking171]

@@austinniemela cool, makes sense

[@Z-Bart]

Yes, you did.

[@MsApollo12]

you're a monster 😁👍

[@Thexkidd]

One day you will run out of cardboard 😂. Be prepared.

[@phillippearce9680]

👍

[@kip8790]

That would absolutely do my nut if I had a metric truck with imperial axles 🤯

[@davefury66]

😎

[@davefury66]

Great work Austin 👍🏼 4 link is looking 🔥🍒

[@DaDudeFromLA]

Kinda scared to watch it go off road

[@JoseReyes-lp6ok]

🇵🇦🇵🇦🇵🇦🇵🇦🇵🇦🇵🇦🇵🇦✔️✔️✔️✔️

[@Alkabo47]

🙋‍♂️🇱🇾