I DID THIS TO PASS MY BUILDING INSPECTION

I DID THIS TO PASS MY BUILDING INSPECTION - 40x50 DREAM SHOP

Рет қаралды 116,819

Күн бұрын

Пікірлер: 239

@LonestarHawaiian Ай бұрын

Go to bit.ly/3BhNHL6 and use promo code LONESTAR for Mando’s Holiday Bundles. They are a great deal for new and returning customers AND just for my followers, Mando is offering an extra $5 off plus Free US Shipping on orders over $30. Thanks to Mando for sponsoring this video! #mandopartner

@user-li9kv9ll8n Ай бұрын

Inswing doors are not secure even with a steel frame , all you need to do is put a car jack between the Jambs and jack 3/4" then push open the door !!!!!!

@gearoidotoole1468 Ай бұрын

I would put red oxide on it not primer

@seansanders789 Ай бұрын

Small tip when drilling metal use oil it will save the bits life by alot

@LonestarHawaiian Ай бұрын

Adding that to the list of learnings from this week… 😂 thanks!

@ManyHats-Woodshop Ай бұрын

Good, it wasn't just me. LOL. I am seeing the bits breaking and wondering where the lubricant is. Always use something to make it easier and keep bits cool when drilling in steel.

@CraigGatza Ай бұрын

just coming to say that, heat is the enemy.. lower the heat makes the bit last longer.

@lkastaas Ай бұрын

@@LonestarHawaiianHi! Three things to consider: 1. start with smaller holes and gradually make them larger. 2. Don’t drill into the ground - it will dull the bore bit. 3 Slow speed and little spray or drop of oil will prolong the life of the bore bits. Keep up the good work - it will be a very nice place to work on your projects.

@kwinders Ай бұрын

Use actual cutting oil like drill/tap oil as it helps the bits bite verses regular oil or spray lubricant will allow more slippage and slow the cutting. Also, as noted, speed is important. If you go too fast, it will burn the bits. The dirt will kill the bits. I was also wondering why not drill the holes, then paint them, or at least add primer and paint to the holes?

@badideafairygarage2258 2 күн бұрын

I am learning so much from watching all of your shop build videos! I don't have an inspection requirement where I am (plus I am not doing brick), but I did have a bit of a struggle getting the neighborhood architectural committee to approve my design. To be fair, they did help me find the right way to get to "yes". Keep up the shop videos - I need you to stay ahead of me lol

@boohanks Ай бұрын

Drilling metal tips…. You’er drill speed is set too high (metal cuts at Lowe speeds) and you need to use cutting fluid or oil to lubricant the bit.

@projecteli_ Ай бұрын

I second that

@davidstjames_ Ай бұрын

Yes, very true. Also, you don't want to press hard on the drill, let the drill bit do its job.

@robertkerby2581 Ай бұрын

Chad, I really respect a man who is a Do it Yourselfer! I think that your building project is looking totally awesome, and I cannot wait to the brickwork! I am a hugh advocate of DIYer's, and as such I have done most of the work on my house for ten+ years. I believe that when you put your blood; sweat; tears as well as your heart and soul into a project that it's reward is to stand back and say, "I did that and it looks gosh darn good"! Well done, Chad!

@ScottyMac71 Күн бұрын

Great videos! Much more informational watching a non-pro do this work than a pro. We dont have the tools that a "pro" uses, so we have to use what we do have! I hate to watch an instructional video to learn how to do something and they have a million dollar tool that I'm not gonna buy to just use it once. Thanks for the content!

@lonestarcollectiblezcom2602 Ай бұрын

Congratulations Chad, what an amazing feeling you must have and as a fan of not only the channel, the car enthusiast aspect, but of the little guy, getting things done through blood, sweat and tears, you've done an amazing job and it's so cool to see you bring it home and next up, bricking this damn shop! I can't wait until it's completed. I reached out recently and gave you some contact info for the bricks, I hope that was helpful! Thanks, Brian - Prosper, TX

@siewertmotorsports5705 Ай бұрын

100% thoroughly enjoy watching the progression you continue to make on this massive undertaking! Can’t wait to see the next update.

@dougdiplacido2406 Ай бұрын

Drill smaller holes first and then work up. It saves your energy and frustration. They make many different thresholds for that kind of door. The weatherstripping is also special for that kind of door. Home Depot will not have it.

@daasebre Ай бұрын

I know you're doing your best with this garage build and I respect you for that, one thing I would have suggested was to ask the steel supplier to drill out those holes for you. Most times they know how far apart it goes. I only speak from experience as a builder in Ontario

@twisted4471 29 күн бұрын

started watching the first episode in class last week and now im intrigued and have finished all of the episodes lol

@TriDaddy Ай бұрын

Chad, that "strike plate" on the door handle can be adjusted so you don't have to push on the door with your foot. Simply use a regular screw driver to bend the tab out causing the door handle not to latch until its pushed harder against the new weatherstriping. This will make it so you allign the dead bolt with its strike plate.

@jabadoo5307 Ай бұрын

Always glad to see another video drop from you. Aloha!

@LonestarHawaiian Ай бұрын

🤙🏽 thanks for watching!

@davidstjames_ Ай бұрын

Another great video, I learn something from all of them! By the way, Lowes does not own Craftsman Tools, Stanley Black & Decker does.

@juliannavarrete586 Ай бұрын

It’s always good to see people build there dreams, it’s going to look real nice! Badass trail boss too 👀👌

@LtSoulRipper 11 күн бұрын

You should always use tapping oil when drilling into steel. Less breaking of bits and taps

@rcrack2 Ай бұрын

Out swing would protect from bad weather. Wind would push on door which would push tighter on weather stripping. Also, harder to kick in an out swing door. Looks good though.

@ScarferBrad Ай бұрын

Out swing door is more secure in bad weather. Wind pushes it away from the weather stripping if it is in swinging

@r3kop Ай бұрын

I would recommend running a magnet tool along the grass to pick up all the metal shards from drilling holes so your dog, maui doesn't get splinters in his paws.

@daracummins6234 Ай бұрын

I love this series and watch out for new videos. I was a little nervous seeing you under the door lintel as it was sitting on the wooden 'ladder'. Stay safe ❤️

@MrRice99 Ай бұрын

Dude! Love your content. Take pride in knowing you are motivating a 48 year old, gear head to do things out here on my property. Proud owner of an AT4 GMC as well!

@JoshuaPanfile Ай бұрын

Been watching you build from the start, I'm impressed how much you have done! I will say that was a clever way to raise the steel, I would never have thought of doing it that way!

@carlunnerstall3226 26 күн бұрын

Love the kids laughing at the end

@Fullion-CA Ай бұрын

So from a machinists perspective. Drilling anything metal and thicker than sheet metal biggest thing is slow and steady win the race and keep the drill straight!

@Marcus_the_Humble Ай бұрын

I love your videos. Please don’t take this as any criticism. If I lived closer I would be over all the time helping. When drilling, pilot holes help. Use cutting oil, keep your drill straighter. Use thicker starter bits. I laugh when you say that new door is solid. They are known as hollow metal doors. When applying smoke gasket and weather stripping, place it on the jamb on the hinge side and on the stop at the header and latch side. It creates a better seal, compresses better and closes better. If you have to gently press the door shut to seal, that’s okay. If it’s too much you can file the middle of the strike plate a little to shift the latch point. If the door doesn’t shut well in the future, you can add a closer. A hydronic piston that assists the door closing. Last thing, you installed the door just fine. It’s easier to place the hinges on the door first. Then bring the door to the jamb and rest it on a 1/2” piece of conduit. With the door on the conduit you can easily roll/slide the door toward or away from the jamb. Tilt the hinges side of the door up or down. Then install one screw on the top hinge then force the door away from the jamb a little to place a second screw in a lower hinge and the rest is easy. When done, if the reveals are off. (1/16” hinge side, 1/8” header and latch side) you can throw the hinges and manipulate the gaps. You can google how to throw or shim hinges. Or Message me and I’ll help.

@MrMadeinthe80s 24 күн бұрын

Biggest salmon ladder ever lol. You should get a mag drill with annular bits. Makes drilling metal like butter.

@danielbednarczyk26 Ай бұрын

If you will be doing the bricks make sure you put flashing, weeps, and wall ties to help keep the bricks up and for the water escape behind the brick... depending your code its 16-24 inches above the ground where you put the weeps every 3rd head joint along the bottom walls, lentils, and doors. When drilling in them use oil and go slow or have tons of bits... it sucks to drill into lentils... Keep it up looks great so far...

@kennetheugene6402 Ай бұрын

If you add oil while drilling strong steel, you keep the drill bit cool and lessen the wear and drill out the holes better.

@reallunacy Ай бұрын

In the future look into an automatic door seal, I know Pemco makes one, they may work really well for the bottom of your exterior door. It mounts into a channel on the bottom of the door and has a button on the hinge face of the door that drops the sweep when it is closed.

@REAL-UNKNOWN-SHINOBI 18 күн бұрын

The one good thing I love about living outside of city limits, is that I'm able to do exactly the same thing as you except I'm not bogged down by inspections.

@omarnunez2402 Ай бұрын

A lighter gauge metal can typically be used for windows and doors. Also they don’t need to be bolted

@scottmcgeorge7182 Ай бұрын

Love the shop so far. Cobalt bit, slow speed and tapping oil or lube. Looking great

@rixtrix11 Ай бұрын

When they remodeled our shop office at work with similar doors, they drilled 1" holes near the top of the frame and pumped the hollow with high strength concrete grout. Code usually requires structural steel to be coated with red oxide primer, not black spray paint. Have to wait til the end to see you pass, lol!

@rixtrix11 Ай бұрын

Congrats on the pass!

@DavidB7474 Ай бұрын

This diy stuff is great! I looked up an LIF security door at Home Depot. $900 Ouch! They had some others are $600

@95dodgev10 Ай бұрын

Fyi those drill bits aren't made of titanium. The gold coating is titanium nitride and is applied to a high speed steel drill. The coating is super thin but helps the drills last longer. There is a huge variety of coatings from mild to wild for tooling and that's why those spyder drills are the interesting blue hue. They using a different type of coating that may or may not be better than the TIN coating.

@Grantski2007 Ай бұрын

Congrats on passing looking forward to the interior finishing 🔨🪚

@sparris3624 Ай бұрын

Hell yeah... 1 more inspection to go! Keep up the great work Chad! (p.s. I had NO idea ur name was Chad til a little bit ago lol)

@teddbobb4672 Ай бұрын

I always use cutting oil when drilling metal, keeps the drill bit cool, and sharp longer.

@401Impala Ай бұрын

With the storm winds you get around there, would've definitely kept it an out-swinging door. Ef the internet "professionals".

@allanstrawn9141 Ай бұрын

The hollow metal door you installed do not come with thresholds as they typically are ment to install a vinyl or aluminum u shape sweep you adjust to drag across the floor or across a handicap thresh hold you slide over the "stop" of the frame and anchor into the concrete. You can also get magnetic weather striping for those doors as well.

@MikeSTGL Ай бұрын

Greatvidea with the stairs stepping up by your self !!

@theANGRIERone Ай бұрын

Congrats, dude. If you're not failing, you're not trying. Way to go!

@vanbigwhiteshed Ай бұрын

Time for a drill press, and some oil. Drill pressing is incredibly therapeutic. A small grinder is great for sharpening the drill bits

@bdpgarage Ай бұрын

Drill a very small pilot hole before drilling them to the larger size. It will got faster and burn fewer drill bits.

@Z-Bart Ай бұрын

Maui's head tilts are epic.

@markw365 Ай бұрын

You need a set of rotabroaches for drilling holes like that, zero broken bits, and < 10 seconds per hole on 1/4" steel.

@texZR2 Ай бұрын

My weekend just got better by watching this video.

@petervento5412 Ай бұрын

Steel door is fire rated so therefore no weather stripping should be on it. Could melt in a fire and not allow for the door to open. So many crazy rubles for building components

@xXKisskerXx 27 күн бұрын

You should get your hands like plaster/cement casted, and then put the gloves on them and display them inside as part of the dream shop. Your "Helping Hands" (also maybe some photos and of course the other helpers like your wife and such) Bonus if you manage to pose them to like hold a hammer or something for extra effect. as for the inspector, as the changes could be seen from your fence, he probably just did the 'yup I see 'em, they fixed it' and moved on.

@tomfritz1391 Ай бұрын

Get some 3-in-1 oil to use on the drill point when you drill iron. You’ll save a lot of bits, they’ll stay sharper, and they’ll drill faster.

@mytubebobbie06h Ай бұрын

I would recommend using cutting oil when drilling that many holes. It will go easy on the bit and the drill gun.

@Laterdays2 Ай бұрын

Now the real fun begins. Just make you corners look and perfect as want. It lames a great place to leave your mark. The corner stone.

@christopher-ricks Ай бұрын

A little oil will help reduce heat and preserve the drill sharpness a bit longer.

@roberthager7438 9 күн бұрын

Maybe they dont sell Dormer in US? Lower the speed and add pressure! Dont drill in too ground, dull's the bit quite fast! Nice work and greetings from Sweden! 👍🍻

@larsmanson9577 Ай бұрын

I use tap magic when I'm drilling holes it works great on saving drill bits and it works great for tapping in some threads

@levik11 Ай бұрын

quality was better on craftsman sockets when it was sold at sears, once they were bought of by Stanley Black & Decker, quality has gone down. Try using Pittsburgh impact sockets from harbor freight with an impact wrench!

@IM808HI Ай бұрын

Nooooo out swinging is better for tornado and hurricane. Because the wind pushes the door to lock if you have an in door swinging once it pops that door your roof goes. Learned this from typhoons on Guam.

@michaelwillis1440 Ай бұрын

Might have been a good time to invest in a mag drill. Drilling that would be so easy and is a amazing asset for a new shop

@maddog8911capt Ай бұрын

I can vouch for the Milwaukee metal drill bit set. those bits mean business! Like you I was breaking the dewalts.

@larryriffett918 Ай бұрын

You can call it a lentol when it's installed i guess that's the engineering name for it. All it is is an angle iron 3×3 or 3×5 or 4×4 plus thickness 1/4" up to 1" if necessary. When I was fabricating I used 1" on big jobs. Hell, I've cut 12" slabs with a track burner & #5 tip & a whole oxygen bank set on 120 pds. Per square inch. That's alot of fun building a dump station or a slag pot hauler.😂😂😂

@PremiumGCCo Ай бұрын

in swing on the side door probably wont be up to code.. high wind will push that door in.

@JoshYoung-u4f Ай бұрын

Love your videos man. Keep up the great work!

@johnnicholls9023 Ай бұрын

When drilling steel like that pain in the arse thing to do is work your way up through the drill bit start with a 6mm then 8mm if it’s a 10mm fixing then use 10mm and use cutting oil make life easier and save on your drill bits

@SilentProfessional. Ай бұрын

Cobalt Bits and a bit of oil is the best combo for metal I've found.

@MM-co9ds Ай бұрын

Use some cutting oil fot the drill bits and invest on a good bit sharpener.

@martinehrlich2748 Ай бұрын

You R doing an unbelievable excellent job. And you’re not even a contractor. Let alone a builder.

@michaelshallue1801 Ай бұрын

Way to go on the side door!!! Don't forget to feed and water the new trees!!!

@LonestarHawaiian Ай бұрын

It’s been raining all week fortunately! I’ll be watering again next week 🤙🏽

@corruptbanjo27 Ай бұрын

Protect puppy paws, get a roller magnetic and take it through the yard where ya drilled.

@jsclayton Ай бұрын

Nice job Ninja Warrior-ing that lentil up without hurting yourself. 🎉🤙🏼

@killacali4283 Ай бұрын

The dewalt cobalt drill bits are really good

@bmac8130 Ай бұрын

I would have made notches in the toungue box to lock up the ends of the safety chains in there as well

@ericproctor1640 Ай бұрын

Great job looking forward next week...👍👍👍👍

@GMCShazamataz Ай бұрын

bit of cutting fluid when your drilling would be nice to see. Love your work. Will look amazing when your done.

@michaelpatterson122 29 күн бұрын

Use cabide bits with oil.

@vinnypinatelli221 4 күн бұрын

So because there is no headers you have to do lintels? I've never heard of them till this video and I use to do construction for 5 years in Colorado! But I was just curious

@verystrange2465 Ай бұрын

Great job and wonderful videos!

@EspenMiland Ай бұрын

@LonestarHawaiian I wonder, shouldent doors open to the outside? Typical reqirement her in Scandinavian🤔

@ScarferBrad Ай бұрын

They should.

@Rune_TTV Ай бұрын

*whistles* Keep it up!

@Mrkdog8081 Ай бұрын

Congratulations Cheeeeee Hueeeee YESSSAH Blessah

@TheSaw410 Ай бұрын

Love my Spyder bits.

@RobertMehrer Ай бұрын

your metal door is missing the weather strip seal on the right side... thats why there is a gap

@adamosity7127 8 күн бұрын

Install electronic door strike on commercial door NOW!

@mullvaden83 3 күн бұрын

I never understood the inswing doors in the USA. Here in Sweden all our outer doors are outswinging. I think its for fire. If there is a fire and everyone runs to the door you just open and run out and noone can block it from opening in panic. And inswing doors you can easily bang in. Outswing is harder to bang in/out.

@thompwa1 Ай бұрын

Use a little wd-40 or some oil when you’re drilling into metal and you’ll save yourself bits as well

@anthonypeachey21 Ай бұрын

Sloe you drill down and use a drilling oil. Don't drill into soil either.

@NBJoeT Ай бұрын

Awesome Great Job!

@Anthony-stama Ай бұрын

Hey I building a skirt two stairs and fixing some shutters and gate opener

@Fossillarson Ай бұрын

Buy good black bits and use oil wd40 even works cut on #1 slow steady. I drill alot stainless steel 😢 green stuff is best lube for us

@Motorcyclefan17 Ай бұрын

Doing it and doing it well!

@EyeMWing 7 күн бұрын

I would have stuck with the outswing door - just install security pins in the hinges (they replace one screw on each hinge) and even if they cut the hinges off the door ain't coming out.