HEMI RAM 1500 CAM INSTALL and START UP!!!

Installing Greene Racing camshaft and hearing how it sounds (note) I did not ask for a choppy idle because it's my daily and I leave for work very early in the morning

[@gabrielgomar5282]

Holy crap I had to watch that on mute

[@venom762]

In most shops that I worked for we would have been fired for using abrasive discs on a head surface.

[@JK-co6wk]

Aluminum heads too. I saw several things in that video that normally would not fly. Like installing the cam bone dry. Assembly Lube is your friend.

[@venom762]

JK yes sir, there's always time for lube!!

[@venom762]

JK I don't get me wrong I'm not one to criticize another techs work but that is hackish.

[@hoost3056]

The fact that the truck is running great and hasn't had any issues despite IH beating it mercilessly shows his guy did a good job.

[@Eatmydick666]

Did he cut out the part where he couldn’t get the cam fully installed because he took a sledge to it?

[@indridcold8433]

Should there be a concern that the camshaft was not greased before being put into the engine?

[@devinfraser9795]

I would say yes lmao

[@themanthemyththelegend7671]

I'm sincerely hoping he knew to wash the pre film off and relube it but the way he was smashing that thing in there those poor cam bearings😄😄😅

[@graysgarage2142]

Yeah I noticed that and it looked like it got stuck until he cut the video. Made me cringe, that boy needed some assembly lube or some molly.

[@melissamollohan5992]

Yes a cam should be greased before installing it shows what they know isn't much

[@williamdavis3509]

Cam lube anyone ❓😬😱

[@RTLife]

This is getting me pumped... all the pieces are coming in for this.

[@IncredibleHemi1111]

Awesome man it's very exciting time when a cam is ready to be installed

[@RTLife]

Sounds like we should be good for weekend of Oct 6th - all the parts will def be in. The Cam is the only thing that needs to be plugged in - going to do an intake upgrade down the road. Would he let me film it like this?

[@blackmambaram7034]

Hell yeah, sleeper mode. Exhaust sounds great. Glad your happy with it. Now to get those new track times. Congrats brother!

[@IncredibleHemi1111]

BlackMamba Ram yea sir... Definitely sleeper Jay asked if I wanted a lope tune but I really like sleeper mode and track times are whats most important to me

[@blackmambaram7034]

Incredible Hemi yeah, it will run much better without the lope tune. Timing is pulled on the lope tunes. So slows you down a bit N/A.

[@IncredibleHemi1111]

BlackMamba Ram Really did not know that thanx no lope at all then... There is lil chop but thats what I wanted more sounding like the way it was b4 cam

[@blackmambaram7034]

Incredible Hemi yeah, your good the way you are. Will definitely be in your favor if you like to grudge race. I wanted lope so I chose a more aggressive cam, sacrificed a little torque to get it and just went higher on my stall to compensate the low end loss to get me moving. Lope tunes are just for sound, not at all worth it for a sacrifice in performance. I had a lope tune on the baby cam I had before and it killed my bottom end, went from 1.76 to 1.8s 60' with a dead bite and top end mph didn't pick up any. I only picked up midrange with faster 1/8 mile but same 1/4 in similar weather conditions. Kinda defeats the purpose of the cam install.

[@IncredibleHemi1111]

BlackMamba Ram Yea id be pissed if I didn't pick up any with a cam install

[@HammerK99]

I'm jealous of that cordless wrench the mechanic has!

[@IncredibleHemi1111]

HammerK99 yea he had some very nice cordless snap-on tools

[@doggieluv78]

Yeah it's nice. But $500 dollars is a bit much. I have a Milwaukee m12 3\8 cordless wrench it cost $150 dollars.

[@ryanpark2049]

@@doggieluv78 You can pay them off bro

[@347mav3]

The 60' slowed down because the larger cam moves up the peak torque rpm. Needs a converter to make the most of it.

[@hellcatredeye-g6582]

Sounds pretty damn good I did mine before I installed my new engine😊Thanks for the video..A lot of people don’t get to see what us mechanics have to do😏

[@IncredibleHemi1111]

Ken Cook thanx man.. Yea cam install is very intailed

[@ronleroy6416]

Ken Cook i

[@18spd4Life]

Would’ve been cool if you left in the parts where he struggled with the cam to see how he got it without damaging the cam, I know they can be tricky sometimes so sharing some tips or tricks could be quite helpful

[@thebigchungus3222]

Did you even watch the video

[@18spd4Life]

Nah I just like to comment based on the title and thumbnail

[@davidgiles4099]

You put the stock one back in,, grabbed it on accident lol

[@bigaceboogiewoogie1928]

🤣🤣🤣🤣

[@newbornlog2789]

You went that deep without going for the full Monty heads long tubes intake bro if ripped my 5.7 apart that much everything stock would go bye bye

[@gvgnstr2668]

damn no assembly lube on a new cam !

[@ChristianHeider1997]

I was thinking the same damn thing. Probably would've gone in easier

[@billwalker790]

Would liked a little instruction NO music

[@StangMode]

Nice 👍 I like that it’s stealth mode

[@IncredibleHemi1111]

EcoBeast thanx man

[@gvgnstr2668]

sounds stock , what a waste .. o wait New Jersey plates that explains the hack job mechanic

[@Hazmatt3446]

Nice growl… I was surprised it didn’t lope.

[@IncredibleHemi1111]

I asked for no lope with this cam my new cam lopes good , u can hear in updated videos

[@MeMe-ej5hu]

I have been waiting for this for 2 weeks

[@IncredibleHemi1111]

Me Me I've been waiting longer than that lol hoping to get some track times on Friday

[@MeMe-ej5hu]

Incredible Hemi I bet, glad it's finally in, can't wait to see your track runs.

[@XHikotheproX]

Get yourself some shielding and ducting for that intake! It's a hot air intake. The factory setup would be better than that.

[@shortbus794]

Patrick H 😂🤣 I call it the same thing. Your 110% right. Glad I’m not alone.

[@parkeranderson5074]

5:57 The viewers: 🙅‍♂️ 🤷🏼‍♂️🤦🏻‍♂️🙋🏼‍♂️ The installer: 😰😱

[@Ep1K0nE]

Sounds Clean. Can't wait to see your new #'s off the line

[@IncredibleHemi1111]

Ep1K0nE thanx man either can I hoping to get to track soon

[@petemedin9698]

Amazing video, amazing sounding cam.

[@dirrtymurph1591]

Damn at least spit on it!!

[@issort44]

🤣🤣

[@melplishka-se8bf]

Ya it did look dry ,maybe picked some scabs on her lol

[@WMills-mi7xy]

im dying

[@cad1995]

I'm liking the sound with cam. Cool video

[@IncredibleHemi1111]

Sixdux Thanx man appreciate it

[@tonyochs3018]

Dude, this sounds like my 5.7 Grand Cherokee with Muffler delete and that is it.

[@cowboyshotgun8066]

My hemi run amazing. No tune up needed, except i put a flowmaster outlaw exhaust in it. Omg sounds great

[@IncredibleHemi1111]

They don't need a tune unless u want a lil more power n if u decide to start modding but yes they run great

[@Eatmydick666]

Elevator music would of made this video 200X better

[@codyhowrey4688]

The really funny thing is that sound just like my truck and I just have a cat back with headers

[@Xxtucker51xX]

Nobody gonna talk about the dry camshaft going in?

[@mrtoddkable]

truck sounds amazing

[@IncredibleHemi1111]

Thank you

[@Emmanuelwithus]

Install was questionable. It sounds GREAT otherwise! Your kid in the candy shop smile says it all man! Here's to the soon-to-be fastest Ram in the nation! Great job and thanks again for the inspiration!

[@bblazeff1]

Sounds like my 5.7 Hemi. I bought it used with not alot of info but it sure seems like it's got an upgraded cam , I wish I knew for sure.

[@ls1powered240sx]

I was wondering, when you pulled your stock cam out did you notice any abnormal wear? I know it's fairly common issue from what I have been reading? How many miles do you have? Are you or did you upgrade the valve train, rocker, ect.?

[@Moteclint]

Sounds good. Install had some flags but it is what it is

[@brianmorg]

Would have been nice to see how he freed the stuck cam.

[@novaguy383]

Cool man, good luck at the track!

[@IncredibleHemi1111]

Novaguy383 thanx man hoping to get there as soon as tuning is complete

[@miguel_garza_official6863]

What’s the name of the song?

[@powerstrokecumminsworking2551]

Looked like a alot of work. Sweet! I'm sure you got some data logging to do for Jay. Lol you can hear me message you at the end of video lol 😂🤣

[@IncredibleHemi1111]

Cumminsworking17 lol yea that was you it was an insane amount of work

[@powerstrokecumminsworking2551]

Incredible Hemi lol, all in good fun tho! I'm glad it went well tho

[@LEGOCAMARO]

Sure would have loved some chop. But understand why can we see the Dino cart see where you pick up on power and torque

[@maldo72]

Love that there is some room in there to work lol

[@IncredibleHemi1111]

maldo72 Yea it was crazy seeing my man stand in front of the motor

[@maldo72]

Incredible Hemi yes lol what part of Jersey are you from I am also in nj

[@McDonalds_vesh]

Never use a rough discs on two smoothe mating surfaces. If I seen some one do that shit to my motor i would have slapped the back of his head off. All you need is a good scraper

[@ET_Don]

I wholeheartedly agree. I have a couple of carbide scrapers that work wonders.

[@joeseda8102]

98% of new gearheads OVER CAM their engines and then wonder why only 10 mpg and crummy idle! It's good you made wise decision to keep it "small"if it's your daily driver. What you need for the street is good idle, more torque and quicker acceleration.

[@speedwack]

Looks sick with no badges. Exactly what I'm going to do to mine

[@IncredibleHemi1111]

speedwack thanks man yea I love it debadged

[@littlebittathisnthatfirear8048]

@@IncredibleHemi1111 im doing mine now... It sucks

[@chefred112]

did you remove mds? I've done quite a few installs and have never removed the intake...just unbolt and hang from the hood, means i didn't have to remove fuel lines too... can't go wrong with a Greene cam..he spec'd a 230/238 cam for my Ram and it's killer..

[@oStirFryo]

Ahh.. The source of the powa! r/t life's video of him foolin in your truck sent me :) Sick truck doood

[@IncredibleHemi1111]

Thanx man... It was a great time hes a good guy

[@robertbryan7373]

All that work.!! No cam lube, or break in procedure..I am curious how many miles u got b4 failure..? 2000..? Sounds like my 2012 jeep grand cherokee with exhaust...dont hear any chop @ all....!! Anyways...just sayin...

[@overlandtate2426]

Man loved the video, thanks for sharing.

[@ryanv7195]

So how did he get the cam in when it got stuck? I think that would probably be the most informative part of the video. What techniques did he use. Did he pull it out a bit and adjust it? Would more lube prevent this?

[@750rocketman5]

He didnt use any lube and i assume he hammered it in.. dont 😂

[@John-vw4qz]

Great sound.

[@gordon3248]

I have 2011 dodge ram 1500 5.7l. Installed stage 2 cam no tune yet have an appointment on the 9th to get tune but can hardly drive getting a to rich code. My question did you have same problem also for the 545rfe tans do you know of a good stall to put in there thanks?

[@cjnthn]

I'm trying to learn as much as I can about the 5.7 hemi, but I had to turn this off.

[@Medix-hg3gi]

Can't wait to see it FSU down that strip!

[@IncredibleHemi1111]

Reynaldo Ruiz very soon you'll see it run

[@Medix-hg3gi]

Incredible Hemi Hell Yeah!

[@JohnsAnythingMotorized]

I always loved the ram Mopar or no car

[@MeMe-ej5hu]

Sounds great, lots of work for the install. How much did he charge for the install?

[@IncredibleHemi1111]

Me Me he's a good friend of mine heconmy charged me 400

[@MeMe-ej5hu]

Incredible Hemi that's not bad at all.

[@FORCESN95S]

Damn, that’s cheap!

[@richardhier4681]

Not having my truck ripped apart.Fuck that !!!

[@AM-km2nt]

How much was this in total bro love the video and it sounds amazing. I’m looking into camming my 2016 ram pretty soon

[@IncredibleHemi1111]

It was about a lil over 2k with install

[@rustyshackelford5892]

@@IncredibleHemi1111 damn my 2013 ram just went out and I'm getting shafted down in Phoenix az I've been quoted 4k plus everywhere I go for stock parts 😢 time to take out the tool box

[@HammerK99]

So friggin awesome!

[@darrellsyrnyk6875]

Yo dude your truck sounds awesome. What cam did you use ? I plan on putting a Clay Smith Cam I'm my 2012 1500 with 5.7 Hemi.

[@rusgts]

Did he even put lube on the cam? Took the head off to install springs???? Who is this guys.....????.... btw love the instructions next to him!!!!!!!

[@mrweeby1961]

Haven't looked inside the Hemi to get my answer but why pull the heads for a cam swap? Were the lifters changed and they have to come out through the lifter/pushrod holes under the head?

[@jrobles1019]

Did this cam require a cam phaser kit? Also did you plug in the cylinder de-activate solenoids? I did a cam swap and left those 4 sensors in the valley but I didn’t plug the harness into them. Just wondering?

[@thevally6127]

I've tried camming my charger RT but no tuner really wanna mess with the Hemi.. that's a cool build tho man

[@IncredibleHemi1111]

Talk to greene racing hell tune any hemi

[@jmata4506]

Hey dude, what are your cam specs? Looking into a cam from a few companies right now. All three have great street cred and application experience.

[@fishermckinzie9688]

What is the cam and the top end set you bought sir mine just dropped on my 2012 in a bind did you have to delete the eco mode shit if so what parts did you get please need help

[@joshuas.4967]

Did you lap your valves when you did this install? My truck is getting Jay's 1.5 V2 Cam early next week, truck has 38,000 miles on it...not sure if the valves needed lapping yet. Thanks.

[@juliovillanueva9418]

Awesome video. I have to do one thanks

[@mikem4432]

for the cost of what? 8-9,000$ to have all that work done? could of put a down payment on a Tundra or another more reliable truck.

[@mrpaul6971]

Holy hell who uses a roloc on a head surface!!!! WOOOOOOF!

[@coocal911]

How much does whole process cost?? Super curious

[@snowcone75]

What was your cost for cam and tune and labor? Gonna do mine in January. What cam did you go with from Jay?

[@christiancordero4060]

Looks good , what cam and valve springs did you install ?

[@IncredibleHemi1111]

Installed Greene Racing .5 HL v2 n .625 lift springs

[@NTfoolhardy]

How did you match up the timing Mark's without dropping the oil pump! I am doing a OEM replacement now due to lifter failure. Trying to get out of dropping the oil pan due to I can not right now. The only thing I have left is to get the timing correct.

[@manowar5516]

Sounds great.👍

[@comfortairheatingcoolingllc]

Hey nice work. Need to get mine done. Was wondering what's the cost and where in jersey is that mechanic?

[@Punishment718]

Where did you get the Cam installed? I'm looking to get a Greene Racking cam kit installed also. I'm in the process of researching recommended shops in the NY, NJ area.

[@hastyhemi8737]

Very nice brother, She sounds great! Can’t wait to see the new track #’s what was her best et before the cam again?

[@IncredibleHemi1111]

Hasty Hemi Thanx man... The best she's gone b4 cam is 12.87

[@DFW116]

I have been doing a lot of research on my 5.7 hemi and really want to do a cam but nothing is giving me a straight answer about if I actually have to get my truck turned or not

[@dodgeram1500tn]

i would had put a mds delete kit on it too

[@dantheman3426]

I’m a little late here with this but I read somewhere that you had your cats removed before you put headers on. I’m in the same boat I have full bolt ons and tune in my 8spd. Just wanted to know if it made a noticeable difference or lowered your ET at all. Thank you

[@IncredibleHemi1111]

Daniel Rios I got a Catless ypipe and thd longtube headers done at the same time n yes that was a very big pick up

[@bri-manhunter2654]

I lost a good bit of torque deleting my cats, I added a high flow cat and that helped bring back the torque.

[@ashtonnuckols2663]

Dudes struggling putting the cam in. Next time put the phaser on for a easier install .

[@abelcp22]

Same into song as Creek Fishing Adventures

[@EliteStricker]

No lubrication on cam? Dry fit

[@billyhope2741]

Damn man, some voice instruction to go with it would have really helped me out. What in the shit is the point in having music over this when you should be explaining what’s going on the whole time?

[@davedavis1789]

Geez four dang bolts to remove the radiator support instead of crawling over and under it!

[@davidallancoe01]

Sounds like my old magnum

[@heathdespain7159]

Did incredible Hemi have Headers before he put the Cam in? Im asking because i have a Dodge Ram 1500 5.7 L Hemi Rumble Bee with Short Tube Headers and thinking about adding a Cam and kinda wanna get an idea what it might sound like.

[@michaelboisselle8590]

Hey I've just seen this video, after putting a ton of money into my vette I'm thinking to do a cam and exhaust for my 17 ram, it's nice to see that you're in nj, I'm in roselle park next to cranford, did your buddy do his ram to and would he do mine?

[@dudleydorite7678]

Need mine done, on my way

[@austinminton4509]

I was looking to do this on my 13. Adding performance lifters and a Greene cam. But I'm running 35 inch tires on my truck so how much more performance could I realistically get. I'm not looking for something that'll run quick times at a track I just want the added power for daily use. Is it still worth the money?

[@seraphimcombat4884]

Was looking to hear that choppy idle

[@IncredibleHemi1111]

seraphim combat sorry it's my daily n I leave for work at 4am

[@seraphimcombat4884]

Incredible Hemi I am going to be ordering a cam from him in a month I told him I want that choppy sound and hellcat pushrods we will see

[@ag5032]

Was curious to where you got the work done as I'm in Jersey and have a ram myself. Also what kind of exhaust are you running?

[@IncredibleHemi1111]

Angelo Golino my friend did it on the side at his local dealership n I have MBRP catback exhaust

[@coryoglesby2174]

How bad was the drone on the highway after you cammed it?

[@Live2die777]

what's needed to complete this?

[@frankhubbard344]

What did that cost to do, I needed done and don't want to be robbed blind .

[@watchwait7117]

What did you end up giving for the Greene custom grind cam man. How did it price up with a comp?

[@ramonpena3011]

A little bit of explanation would be great

[@mauriceware3429]

How much a job like that cost on a '04 Dodge ram?

[@BuilditRT]

Man can’t wait to do a cam for my Charger what did you end up going with? Custom grind from Jay?

[@IncredibleHemi1111]

Build it R/T I went Greene Racing stage .5 HL v2

[@BuilditRT]

Incredible Hemi awesome I may just have to go with Jay when I am ready for a cam

[@joerivas9847]

That new cam probably failed. No assembly lube?! And if it didnt lucky duck. Dont rely on luck hen working on engines.

[@fabianfonseca3781]

I own the same Ram 1500 brilliant black and was wondering what the link to purchase the camshaft kit ..?

[@Jeremiahheartly]

Lmao Ford tried hitting me with that shopping ram add in the beggining gtfo I'm here for a reason