Delta PLC With Stepper Motor | Wiring | Programming | Pulse Calculation | English

[@mikefreedom5612]

Thanks!

[@ravichandranjothiraj6628]

Dear Sir, It is very interesting to learn from you...

[@marahat6865]

There was a very nice way of explaining the analysis. I saw it from Bangladesh. It looks like I am listening in Bengali

[@Kishore.96]

Nice nice explanation. watching from Andhra Pradesh state Vijayawada and your subscriber also ❤

[@mikefreedom5612]

Good , do you example of programming analog input, like pressure or temperature ?

[@gilbertdevera3339]

Very helpful thank you

[@mohammedsuphiyan6853]

thank you... keep sharing

[@silambuarasan5316]

Super👌

[@md.sharifulislam5407]

nice sir

[@ekambaramvenkatesan7609]

Hi sir good job

[@heshamzahra4836]

Great work but i have one question what about hardware configuration in delta WPLsoft please and thanks again

[@IndustrialAutomation]

Thanks..White creating new project you just need to select PLC Model no...no any additional configuration required..

[@heshamzahra4836]

@@IndustrialAutomation you mean no configuration of Y0 and Y1 because i see when you describe it write CH0

[@NeerajGupta-xs1lp]

@@IndustrialAutomation hi sir pls share your number

[@thepurposeofmyexistence2511]

Nice video sir , but can you make same video on schinder or simense plc

[@IndustrialAutomation]

Already having the videos on siemens..

[@رازموفقبودن]

Thanks

[@bhagyeshpatel2739]

You have experience with Click PLC and Gecko Servo drive. I need help

[@solomonndhlovu7672]

nice and best explaining no your plc program

[@dhanarajsuvarna7835]

Can you make video of flow rate calculation in delta plc.using pulse input.

[@ekambaramvenkatesan7609]

Sir Please explain for two stepper motor forward and reverse through joystick

[@upereye3423]

Sir if one servo graphtec vinyal plotter mother board is dead can it can run with another mother board motors pin by attaching double wierd with help of plc to run one board with 2 plotter?

[@rahimkhan-li6ei]

Can we measure the pulses by multimeter...

[@shadabdadkhan9238]

Sir hindi me video bnaiye plz

[@aditya21212121]

I have same drive and i was confused with the power supply required . i purchased 36v 15 amp power supply. however was bit skeptical whether it will work or not, as it is written Ac and Ac for vdc and gnd terminals respectively. you helped me by letting me know that it also accepts DC inputs, thanks

[@Shubham_848Vlog]

It work or not??

[@aditya21212121]

@@Shubham_848Vlog it works. Connect live to top AC and neutral to second AC.

[@tusharbansod2522]

Sir how to make stepper home condition in plc

[@ravichandranjothiraj6628]

Can you please also integrate delta hmi to delta plc

[@abinvbabu9972]

Sir can you do a programme about Modbus communication

[@Boss-dy4lw]

Great Infos, I kindly request your guidance in suggesting a Delta PLC model along with suitable expansion modules that would allow me to control around 24 to 30 stepper motors, sequentially and a few of them simultaneously. Ideal output pulse frequency would be upto 5 kHz (less might also work). Greetings from Germany :)

[@mikefreedom5612]

🎉🎉🎉

[@JohnGeremew]

instead of stopping when it finishes its signal pulse i wanted the servo to repeat itself. how can i do that? help me sir

[@vaibhav7496]

Thank you for sharing knowledge with us. Can you provide more details like how to choose Stepper Drive capacity as per application? Means any calculations somethimg so to correctly size drive.

[@thepurposeofmyexistence2511]

Dear sir how can a servo driver read g code of cnc ,,, is there any converter device we use to convert g code to signal 0 to 10 vdc so that servo driver can read it

[@neerajdhiman9589]

hello sir, i want to learn plc programming,

[@wigahd4171]

Sir bhut hi accha btaya aapne lakin aap sari vedio hindi mai bnaye english mai samej nahi aata

[@vigneshwarkarthik0194]

Kindly explain DDRVI INSTRUCTIONS and how to calculate motor speed in frequency

[@indianmaker1805]

Delta DVP14SS211R and DVP14SS211T me kiya difference h and good konsi pLC h

[@pratheeshlalpradeep2159]

Bro...how to increase the speed of stepper motor

[@IndustrialAutomation]

Hi..It's mentioned in video

[@dhanarajsuvarna7835]

How to count high speed pulse in delta plc

[@Wolfhunter666]

Hello, are you available for some freelance works for stepper motor programming?

[@IndustrialAutomation]

Yes..

[@ameysalvi5973]

Hello, can you help me in distance calculation. How we can calculate required pulse for 100mm distance

[@MrThebebin]

hai bro i have 5V signal stepper drive how to wire that with resistors? thank you.

[@IndustrialAutomation]

Connect resistance in series

[@MrThebebin]

@@IndustrialAutomation 24v dc to 5 v dc ..how many ohms ...smps is 4.5 Amps

[@SathishKumarVickyenterprises]

Hi bro can you send me this ladder. I eant practice

[@MrThebebin]

hi sir can I get a backup of this program, thank you.

[@IndustrialAutomation]

If you do it self, it would be more beneficial and understandable to you...

[@MrThebebin]

ok bro it is working thank you,

[@DilipKumar-uw3ly]

@@MrThebebin Can you share the program if possible

[@MrThebebin]

@@DilipKumar-uw3ly tried the program?

[@DilipKumar-uw3ly]

@@IndustrialAutomation New to the programming world, will be great if it is shared to understand easily

[@innvotechsolutions3576]

hello is it possible to run stepper motor will run with max speed 10000pps, creep speed 200pps and acceleration and deceleration 200ms and number pulses 50000 pulses with resolution of stepper drive 200 . with help of delta dvp 28SV plc

[@IndustrialAutomation]

Need to check ✅

[@innvotechsolutions3576]

@@IndustrialAutomation have you checked?

[@Aliproductionpk]

Plz give me this program

[@Shubham_848Vlog]

Dear sir please confirm SMPS selection for small LT panel Also confirm about high speed extension Do module (DVP08SN11T ). Can we select this for high speed application

[@kalpeshthakkar5818]

Hi sir ,have a good day, I need your help, I shall try to make 3 axis(X,Y,Z) PLC(delta dvp 10pm) operated plasma/oxy fuel cutting machine | In position control mode ,we will have to continuously sending pulses in servo drivers for distance and velocity as per target X,Y,Z coordinates and after will completing any commad we want feedback from ac servo drive(panasonic make) for comparison,and closeloop purpose | how resolve this issue please suggest me any hmi software or idea,

[@BalaMurugan-dk2zk]

That pulse dmov option doesn't move pulse input

[@IndustrialAutomation]

Please check your register...it shouldn't be used anywhere else in program at output

[@kdr-TheVoiceOfIndia]

Brdr, can you give your email for discussion....

[@Himanshu-ws3vl]

atleast could have shared the link for the code man

[@IndustrialAutomation]

Don't just copy paste buddy.. Understand the logic and try to write yourself...

[@Himanshu-ws3vl]

@@IndustrialAutomation ya started trying IPS says m1000 isn't available selected right version of plc still.

[@balvindermatharu922]

Zoom ladder diagram

[@harshdhansawale8838]

Please explain in hindi