Injector Replacement On CUMMINS 6.7 RAM Trucks

Replacing a bad injector on 1000 ft/lbs 2020 Ram 3500 with 6.7L engine (same procedure and tools for 2012 and up model years). 2019 and up vehicles with Cummins engine are now equipped with hydraulic rocker arms so torque procedure is different.
Tools I used in this video:
Injector tube/connector removal - ebay.us/p9j3WQ
Injector removal - ebay.us/p9j3WQ
1/4'' torque wrench - amzn.to/37ZaHMn
3/8" torque wrench - amzn.to/3oNNYJJ
Fluid evacuator air and manual - amzn.to/3mbGE92
Hose clamp pliers with removal hooks - amzn.to/2KeBGvg
Oil filter socket set - amzn.to/2Lpu4Xb
You can never have enough 8mm sockets! - amzn.to/3oNtX6n
Clip removal (good for vacuum hoses too) - amzn.to/343PaRv
If you make a purchase through these links I may earn a small fee at no cost to you!

[@thetwins706]

This video has it all. Thank you so much. One way to get the feeder tube out without buying the special tool is once the feeder tube bolt is removed you can lightly reattach the fuel line onto the tube and it’ll give you more leverage to pop it out

[@glennbeadshaw727]

It's mind-boggling the amount of work to change an injector you would think somehow they would have the injectors on the outside if possible because I don't even comprehend wiring being on the inside of the cylinder head without just melting totally

[@dougc117777]

I could watch this all day. I have a 6.7 Cummins and I love watching maintenance videos. How in the hell would you ever remove the injector / tube in cylinder 6?

[@youjizz1991]

Im guessing cab off

[@randomrandywv1381]

Struggle a bit more. Just did it on mine. Offset wrench (3/4” or 19mm) is necessary. Torquing things is a bit more difficult due to space constraints

[@FireBosspilot]

I read that you should always replace the injector tubes when swapping injectors. The tip of the tube forms its own seat on the opening to each particular injector.If you re-use it on the new injector, you run the risk of leaks.

[@kingpeasant5099]

Thank you for the video. I'm about to replace all 6 of these plus the pump on my 2020.

[@totalarchertx11]

Did you change them yet? I’m on the verge of swapping to 60% overs but nervous of the difficulty lol

[@kingpeasant5099]

@@totalarchertx11 I did. It wasn't the easiest job I've done but it was pretty straight forward, overall.

[@dstich1164]

After done do you need a pc to reset the injectors values?

[@gilhopkins2465]

Thank you that helped

[@shauncollins2017]

Its actually cheaper to replace all 6 injectors on the 2019+ Cummins 6.7's. 1 injector by itself runs around $1800. A 6 pack of injectors runs $2700.

[@anggelomunoz6685]

Hola cambie un inyector en mi ram que estaba malo 2500 2012 6.7 Cummins y le coloque otro nuevo y sigue funcionando en 5 cilindros el motor o habra que codificar el inyector?

[@bashark9]

I just had my engine replaced, wanted to do the IQA program for the injectors, got the I ejectors out and non of them have codes 😭 What should I do??

[@TDRAuto]

Sorry for the late reply, Cummins 6.7L injectors don't need to be programmed, you only need to reset the injector values.

[@harleyhoracio1]

Would like to see how you tackle replacing #5 or #6.

[@youjizz1991]

I was asking myself the same question…cab lift maybe?

[@justinp6383]

@@youjizz1991 not needed, you can get to them with no issue its just more of a pain

[@bashark9]

Can you get the injectors code without getting the I ejectors out? I replaced a new engine and need to do the IQA program for the injectors

[@kenrunions223]

I don't see a final torque number on the injector hold down, you went straight to the rocker replacement after the the connector tube torque. 8 NM seems awfully light when every other 6.7 before it is recommended at 79" lbs.

[@simonhernandez3354]

So I took the exhaust side push rod out to clean it cuz some debris got on it well when I went back to put it back on it sits higher than the rest if I tight the Allen bolt it wants to bend what can I do to fix it?

[@ethanslaughterbeck3579]

Did you have to rotate the engine at all?

[@gb4807]

hello, on 2016 ram 2500 do I need to type in the code for the injector or is it only on the fifth chance?

[@zm5189]

2018 also need to be reprogrammed?

[@gb4807]

yes

[@multi-transportationsystem11]

Great video thx ? What makes an injector go bad is it bad fuel

[@TDRAuto]

Contamination is a big one, I had one where the pick up pump failed and sent metal debris through the filters to the high pressure pump and clogged up the injectors.

[@explorerscene]

Relly good video

[@DGDustysRoads]

THANKS YOUR VIDEO HELPED ME TOO MUCH I’m in Dallas Texas and I work on construction if you need any help just let me know I love to do all Maintenence on my trucks and I just got my first diesel truck it’s a 2019 2500 ram Laramie and is really hard to find any help with this new truck

[@randomrandywv1381]

Awesome video!!! What software are you using for the scan tool/computer?

[@pinktacotuesday4573]

can I reset/reprogram my injectors on a snap on scan tool? just got my injectors Flow tested and cleaned and need to reinstall.... Thanks!!!

[@TDRAuto]

Sure, as long as that function (offset reset) is supported by the scan tool.

[@estebanamador7601]

"How much does this work costs?" : Let's see: $200 for labor and $1000 for patience. 😂😂 I don't live in USA, how much does this cost there? (#6 is a nightmare)

[@ramonelizondo6996]

How would you change injector 5 and 6

[@n_rip8344]

So the rocker arms/valves/bridges don’t need to be timed/gabbed anymore on the 2020s?

[@TDRAuto]

There are no adjusting nuts anymore, it’s all hydraulic now. If for some reason removed there is that timed multistep tightening procedure to allow for proper oil bleeding of the hydraulic lifters.

[@brandoncarter8584]

Just replaced all six high output injectors in my 2019 Ram 3500. Now she won’t crank. Any suggestions from anyone?

[@penguinsgarage]

You locked it up with something

[@bpina2182]

2020 and already needs an new injector?

[@TDRAuto]

I haven't done another one since, I believe it was a rare occasion!

[@nicknetefor7116]

He said he thought someone was in there already because a couple bolts were too tight