10 dislikes?? I give you 10 likes. What a simple and safe sollution. 👍🏼👍🏼 Thanks for this tip!
@Phelycs226 жыл бұрын
Wow you just saved me 50$! I've just tried it and it works perfectly. I did offset the tape just a bit on the outside layers to be sure not to hit the inner lip. Thanks!
@MotorGuyzer4 жыл бұрын
I was pounding on the seal on my DR650 with some plastic pipe and wasn't getting anywhere. Tried your method and it went straight in. Thanks for the great tip 👍
@mattcc6603 Жыл бұрын
Cheap, safe, foolproof - love this. Thank you for sharing.
@aragos327273 жыл бұрын
Thanks for this. I was just about to thanks for this. I was just about to order the tool for it and you just saved me a week of downtime
@GoldbergPatriot7 жыл бұрын
Now this is what I like, creative solutions!
@dannyvaughn3665 жыл бұрын
Thanks! I was wondering what would be a simple solution and this is it. You Win a million points that don't matter. Awesome Job.
@robertgisthebest5 жыл бұрын
Thank you so much for sharing this knowledge. I did try the pvc pipe method, but it just wasn't applying enough pressure. With some luck this method will work.
@evanphi8 жыл бұрын
Never seen it done this way. Cool.
@greggbabbitt67942 жыл бұрын
Awesome damn idea!!! Thanx so much!!!
@ozankiraz682 жыл бұрын
I used this method today, and it just worked
@herwigvanhoof16807 жыл бұрын
Works great! Thanks mate! Very helpful video.
@sawboneiomc88093 жыл бұрын
Never would have thought of that
@edcones29484 жыл бұрын
Well! This is a new one. Have you tried to this with the old seal above the new one to avoid damaging the new one? I've used the old seal as a driver for years, but I have to find a way to whack on that. :)
@Alperider5 жыл бұрын
And finally a God!!! Thanks a lot
@Stein_NZ5 жыл бұрын
thank you... going to try this now....seal is tight..
@robans Жыл бұрын
You are the first t one that created a lip when rolling electrical tape, everyone just roll it straight. I think the lip is important not to damage that soft part of seal, at least thats what I think, I dont know I am not an expert. 😂
@roscoejones3743 жыл бұрын
you just saved me 50 bucks, thanks dude
@Skotm0013 жыл бұрын
Right on!
@losantonio9049 Жыл бұрын
Does your seal have a spring ring around it. Shall I remove it to fit the sloped ring? This method drives the seal with solid hits but the seal still won't squeeze into the sloped ring
@heydenlabelle5137 жыл бұрын
Quality info. Thank you.
@grundell29304 жыл бұрын
Farkin legend!
@Skotm0014 жыл бұрын
Sharing the Knowledge!
@obfuscated30906 жыл бұрын
Those objecting based on theory may note that if the method didn't work, the forks would leak immediately. What happens is the tape conforms to the seal while spreading the load as it expands slightly over the seal lip. Any assertion is testable. If it works, it works.
@JohnDoe-yj9tj6 жыл бұрын
Does the tape method work for driving the fork bushings into place as well?
@williamfunes27405 жыл бұрын
Yes. I did the bushing with tape as well.
@Eve....7474 жыл бұрын
Like to see that 1, lol 😂
@Isalys5555 жыл бұрын
awesome ! thanks for the tip.
@209golightly7 жыл бұрын
how about any little marks on tue tube, could they be cleaned?
@NeverSquid7 жыл бұрын
Good stuff!
@slowflnger8 жыл бұрын
smart man
@talraskin99784 жыл бұрын
but how do you put the bushing in? because i saw people using the driver tool to push the bushing with the washer and then push the seal
@intelin1237 жыл бұрын
nice work. thanks
@klacow3 жыл бұрын
what did you use to drive the large bushing in right before the seal?
@Skotm0013 жыл бұрын
Hmm.. I never needed a driver for that bushing, just slide it in and it snaps in place.
@klacow3 жыл бұрын
@@Skotm001 ok, thanks, never did it before, just double checking, lots of vids show them using the driver for both bushing and seal, thanks for vid
@Skotm0013 жыл бұрын
@@klacow cool, good luck!
@oxygenfiend57503 жыл бұрын
Best and cheapest way to do this
@erginyilmaztenor7 жыл бұрын
really smart
@gibronnaqeelandries34068 жыл бұрын
will it work if u cut the old seal in half and use to drive in the new?
@KurumaDesigns7 жыл бұрын
GIBRONN AQEEL Andries Yes but dont cut in half, cut just a little portion out of it
@YTjndallas4 жыл бұрын
Dude. That trick is the tits!! 😃👍🏻
@SANDS785 жыл бұрын
Wish it was that easy for me. Been trying everything I can think of, they will not seat.
@TheFrog7673 жыл бұрын
Another method in the head for later use if needed.
@MrRetread4 жыл бұрын
Dude!!!
@wacekplacek64667 жыл бұрын
And now check your fork seal spring, you are putting force directly at seal point where the seal spring is located. Never do this again. Use composite tube to do this next time.
@Skotm0017 жыл бұрын
Wacek Placek My fork seals are all in great condition with zero issues. But thank you for your opinion.
@shoeik52768 жыл бұрын
No way. You can not do that, You are just making damaged on the lip of the oil seal. You have to push in out side of the seal ,not inside. I hope you are not making money fixing them.
@Skotm0018 жыл бұрын
I build up the tape to the same thickness of the seal, it's exactly the same as using a specialized seal driver. I've done it this way for years with no issues.
@gibronnaqeelandries34068 жыл бұрын
SKOTlikesBIKES true does work and by the way to spend so much money on a seal driver tool is a joke u don't use it often
@wacekplacek64667 жыл бұрын
You are right, but the thinking is the problem for him.