Install Thinkware iVOLT BAB-50 Battery Pack For U1000 Dashcam Parking Mode

Buy Thinkware U1000 Front & Rear Dashcam (2 Channel)
US: bit.ly/Thinkwar...
CDN: bit.ly/Thinkwar...
** Use links to purchase BlackVue devices (5% Off Over $250 USD or $300 CAD Purchase).
Buy Thinkware U1000 Front Dashcam (1 Channel)
US: bit.ly/Thinkwar...
CDN: bit.ly/Thinkwar...
Buy Thinkware iVOLT BAB-50 Battery Pack
US: bit.ly/iVoltBAB...
CDN: bit.ly/iVoltBAB...
Buy Thinkware Radar Module (For U1000 Dashcam)
US: bit.ly/Thinkwar...
CDN: bit.ly/Thinkwar...
=========
Shop BlackBoxMyCar Website For All Dashcam Products
US: blackboxmycar.com?ref:dial2fast
CDN: blackboxmycar.ca?ref:dial2fast
=========
In this video, I will be reviewing and installing the Thnikware iVOLT BAB-50 Battery Pack used as backup power for the Thinkware U1000 parking mode. This battery will extend the parking mode to 16 hours. With this, it will also eliminate the strain of your car battery if you are to hardwire your dashcam direct to the car battery.
The BAB-50 uses LiFePo4 battery cells and can operate in extreme condition safely (-10C - 60C). Check out the link above to purchase this battery system.
=========
FUSE TAPS:
ATO/ATC Fuse Tap:
US: amzn.to/2NmH4fL
CDN: amzn.to/2nwqLS1
Mini Fuse Tap:
US: amzn.to/2wR0G24
CDN: amzn.to/2m6ins3
Low Profile Mini Fuse Tap:
US: amzn.to/2wUzkqQ
CDN: amzn.to/2ltHHrS
Micro2 Fuse Tap:
US: amzn.to/2MSBtOJ
CDN: amzn.to/2mWMG4P
FUSES:
ATO/ATC Fuses
US: amzn.to/36pxGgN
CDN: amzn.to/2RtqdZY
Mini Fuses:
US: amzn.to/2sWVpqZ
CDN: amzn.to/2RQKCqC
Low Profile Mini Fuses:
US: amzn.to/38PkmUH
CDN: amzn.to/37DlaLO
Micro2 Fuses:
US: amzn.to/2vo5Btt
CDN: amzn.to/2RrF9I3
=======
TOOLS:
Car Panel Removal Tools Kit 18pcs
US: amzn.to/2KO7688
CDN: amzn.to/2YLH3bz
Auto Ranging Digital Multimeter (Test: volt, ohm, amp, diode, etc)
US: amzn.to/2JSSHrB
CDN: amzn.to/2PKPCxI
Professional Wire Stripper
US: amzn.to/2REssbn
CDN: amzn.to/2lRA1jr
Klein Tools Single Pull Wire Stripper
US: amzn.to/2Rw63ga
CDN: amzn.to/2nBl7OI
Channellock 909 Wire Crimping Tool
US: amzn.to/2xzGDFa
CDN: amzn.to/2m7qAfN
200 PCS Insulated Wire Butt Splice Terminals
US: amzn.to/2NZ3MdK
CDN: amzn.to/2mXHCgq
Scotch Super33 Super 33+ Vinyl Electrical Tape
US: amzn.to/2RAk1Od
CDN: amzn.to/39qagdF
LED Work Light Rechargeable 20W 1600Lumen
US: amzn.to/31lGp0L
CDN: amzn.to/35HiL2n
=======
Shop Dial2Fast Store For List Of Tools & Parts
US: www.amazon.com...
CDN: www.amazon.ca/...
=======
Support Dial2Fast on Paypal
www.paypal.me/...
Support Dial2Fast on Patreon
www.ptreon.com...
Dial2Fast website
www.dial2fast.com
Like us on Facebook
/ dial2fastofficial
Shop Amazon
US: amzn.to/2LqTtuk
CDN: amzn.to/2L5QASt
Join Amazon Prime
US: amzn.to/31i05mP
CDN: amzn.to/3kG0D0R
Try Amazon Prime 30-Day Free Trial:
US: amzn.to/2S3GjHI
CDN: amzn.to/3kG0D0R
========
As an Amazon Associate, I earn commissions from qualifying purchases with the links provided here.

[@blackboxmycar]

Thanks dial2fast. Great video!

[@zeke1973]

I think the back up batteries are definitely worth it since my car sits for a few days (I have a work vehicle). I have the U1000 and I installed the Cellink Neo hardwired in my car. like that it fully charges in about 20-25 minutes. I'm going to buy the Radar module but i'll wait to see from dial2fast next video to see if it's worth it. Just wish the Cellink Neo had a USB port so I could connect a 4G mobile Hotspot to it so I can get alerts.

[@whatme1923]

i have cellink neo its great battery and gives you 24hr+ of parking mode for 2 channel dashcam i have thinkware q800 pro! and the u1000 radar module is for when you activate the powersaving mode its just give you 20second clip after impact but for radar module you will have the advantage of before and after the impact for powersaving mode similar to motion detection and goes back to sleep if no impact detected and it will go back to standby mode if there's motion is detected the goodthing with powersaving mode it will double the number of parking mode hours !

[@kirbyljack]

With you having a work vehicle, what happens if you let the car sit for a while and the external battery drains? Does it’ll the days cam still draw from the car battery, or does it just shut down from no power?

[@zeke1973]

Jack Kirby the cam will lose power once the External battery runs out of power. Cellink has the ability to add a second battery so you can double the runtime when the car sits for the week.

[@Steve-os9dg]

Great video! Do you have a video on how to install BAB-95 battery? The BAB-95 has more wiring but lasts longer.

[@swr1240]

Awesome explanation! Thanks so much! Really helped me do it on my own instead of paying someone to do it.

[@cayrick]

Good video. Perhaps I am a little slow but I was confused when you talked about your original installation of the hardwire kit prior to the addition of the ivolt battery. You showed the existing hardwire cable install connections to the fuse box but were not clear that you removed the fuse taps prior to connecting these wires to the output cable from the ivolt battery. It is clear to you, but somewhat confusing to the unskilled person doing this for the first time.

[@dial2fast]

The original hardwire kit I installed (which I showed the installation in my first U1000 review video) requires both an ignition 12V and constant 12V fuse tap into the fuse box. When I installed the iVolt battery pack, the input to the battery pack only requires one ignition 12V fuse tap 5:48. On the output side of the battery pack, I connected the 3 output wires to the 3 input wires of the power cable going into the dash camera 6:45.

[@AnonymousHippo5]

How does this compare to the Chanun Power battery pack? You can buy 2.5 Chanun Power battery packs compared to one of the Thinkware iVOLT BAB-50. The Thinkware needs to last 2.5 times longer to make it worth buying. (This is referring to years operating trouble free in your vehicle)

[@OutletFlow]

Thank you so much! i wonder if the car heater will affect the battery at all or if the Florida sun bake the battery pack.

[@seanvan6377]

So you removed the fuse taps from the original installation ?, then cut those taps from the 3 wire harness where you had spliced them together ? I didn't see that part anywhere or did i miss something ? Did the butt connectors come with the camera, 3 wire hardwire kit or the battery ? Thanks

[@richeyrich6855]

Great question Sean! I just watched this video and I was wondering the same? Do you remove the original hardwired fuse cables now that you are installing the Ivolt battery pack which is designed specifically to work in parking mode. Sean I don't see that this gentleman responded to your question. If you have the answer it would be greatly appreciated. Thank you in advance!

[@riotfiftyk5508]

If they release a 3 Channel Dash Cam, I hope they make the third Channel able to rotate into whatever direction you want.

[@just4therecord]

There is one from viofo just like that called T130

[@Futureisbright123]

Your video is very much clear, to the point and very useful

[@dial2fast]

Glad it was helpful!

[@cayrick]

In my case (2022 Honda CRV) there were no switched 20A ( Thinkware suggested) circuits that were switched. In your case I beileve you found the same. I see you put a 20A fuse in the tap with a 10A. Would this mean that if the circuit draws more than 10A while charging the battery you would blow the 10A fuse? In my case I see no other option that doing what you have done.

[@Notthatguypal40]

After the battery is installed how do you know that it’s working during parking mode? Is the light supposed to stay on?

[@envyexploud]

The "200 PCS Insulated Wire Butt Splice Terminals" you linked do not work well. The hardwiring kit wires are way too thin, even with a proper crimping tool...

[@hollywood5163]

The wires that go into the fuse box in the car are pretty tiny for the voltage.

[@derekdukhu2825]

Hey great install video. I was wondering which fuse slot you went with on your install (ex. Accessory or Option)? Thinkware says to go with a 20a fuse slot and use an equivalent 20a fuse in the fuse tap, but on my Acura RDX, all the 20a slots are constant power, even when the car is off. Your help is greatly appreciated.

[@dial2fast]

On my 2019 Odyssey, I tapped into the igntion 12V fuse labeled Option. On the battery pack, the charging switch Low is 5A, and High is 7A. So tapping into a 10A fuse slot will work fine.

[@A42yearoldARAB]

Be aware that a car sitting in the sun for hours can still exceed that temperature. Better to just add a second actual car battery and hook that along with your radio equipment up to it.

[@BrayoFitnessTrainer]

A42yearoldARAB what will happen if the temperature is exceeded?

[@7arkhwf]

Thanks for the tip, could you please explain how, & which devices hook to that second battery? Thanks

[@richeyrich6855]

Actually these types of batteries are Lithium Iron Phosphate and designed to work in high interior cab temps.

[@fawazmohammed914]

Thank you, how to know that you make a right connection to the fuse box , is there any indicator?

[@KamiYamabushi]

If you get this battery, is it still worth using the battery protection cut off to protect the battery pack itself? And what would be the recommended voltage cut off for the BAB-50?

[@dial2fast]

There is no published info stating what shutoff voltage you should set the dascam to. But I am pretty certain there is a protection circuit inside the backup battery that will cutoff the output when it drops to a certain voltage. This will prevent any damage to the battery. If you want, you can set the cutoff voltage on the dashcam as low as you want and this is fine because the backup battery is not used for starting the vehicle, so doesn't matter.

[@nasaspacemanwho6711]

thanks for the vid, it's exactly what I'm looking for. can you double up the thinkware ivolts, so you have more capacity?

[@dial2fast]

I don't believe you can do that with this battery pack. It doesn't have a port for daisy chain connection.

[@dianaromero5706]

not connecting it to the car battery.....is there a video showing just the cigarette connection....seems there is no wire for that

[@NJNino82]

Why is my camera shutting off over night with the same setup as in the video? My battery cutoff settings are disabled

[@roddyfo4rthseal207]

How is the battery still performing? Online about to order. Would you still suggest Ivolt or a different battery for thinkware U1000 4k dash cam?

[@noorielaboab1032]

My car fuse box is inside of engine; (Toyota PLIUS) because that I used my cigaret power supply - CAN YOU SHOWING HOW TO REWIRE WITH THE CIGARET PLUG? My car was already hit in the parking lot and my camera is installed only to work when I start the engine, Thank you.

[@ED-gz8vr]

how do you install this battery with A Multiplexer Box and 5 channels Dash cam?

[@thanhhungrestaurant8348]

Hi, can you please tell me what your 'Battery Setting' in the THINKWARE CLOUD app? Thank you.

[@gordoneaton564]

Looks great idea and battery pack.

[@TINGSTARR]

Great instructions. Thanks.

[@Shempagne]

Hi, Question and apologies in advance. I have the thinkware u1000 and the Blackvue B124x. The B124x is being charged via the cigarette port and the thinkware is also connected to the B124x via the cigarette port. Does this prevent the parking mode from being engaged and if so, do I change out just the output cable to the 3 wire from the the cigarette wire for the dashcam to the battery, or do I also have to hardwire my battery to the car and also the dashcam to the battery?

[@dial2fast]

The U1000 need 3 wire connection for parking mode. The B124 can be charged with cigarette lighter.

[@EsenbekAliev_]

did the camera ever drain your main battery? I got a message on my 2020 Odyssey this morning that battery level is too low after running this camera for few days now, it did start as usual and voltmeter shows 14.3 when running, just curious. I'm getting the battery pack on black friday :) Any other recommendations for battery pack after you used it for so long? Something better but in the same price range maybe available from thinkware ? Also, how long is the battery pack wires, will it be enough to reach spare tire compartment? I have my amp, audiocontrol lc2i in there, so I might put battery pack there too

[@dial2fast]

Since you said you are getting your battery pack on black friday, then I am guessing your battery low issue is from the dashcam being hardwired to the fuse box for parking mode. If this is the setup you currently have, then yes it does drain the car battery every time you park. You need to set the voltage cutoff on the dashcam to protect the car battery. Once you install the battery pack, the dashcam will NEVER drain the car battery when parked. It will be running off the battery pack. As for installing it in the spare tire area, it should reach since the spare is located in the second row. But keep in mind the battery pack need ignition 12v, and not constant 12v source.

[@jattlifestyle]

battery pack can be installed by obd option

[@jro21]

Do I have to turn off battery protection?

[@user-vo7tj4bv1z]

Yes

[@user-jc3hx2sq9o]

Does the rear camera independently detect motion and start recording during motion detect parking mode? Your info is much appreciated. Trying to figure out if I need 2 front cameras or just a 2Ch unit.

[@dial2fast]

Yes the rear camera also detect motion.

[@user-jc3hx2sq9o]

​@@dial2fast Do you still made this unit to perform a test? Getting mixed answers and some say the rear will not detect motion and only start recording once the front unit does during motion parking mode. I'm usually head in first and the front camera is facing a wall, so it won't detect motion if someone walks by the rear to initiate the record.

[@Danger_Dingus]

Are the instructions for installation included with the product? Edit: Also did the product include all the wire crimps that I see you using?

[@stevencheung309]

What if you don’t want any recording to happen when you are parked in a secure garage versus parking in non secure public parking space. Is there a way to preference these recordings?

[@dial2fast]

There is no scheduler for when parking mode recording happens. If you don't want parking mode recording (with this system setup), then switch the battery to the off position.

[@stevencheung309]

@@dial2fast thanks for the reply. Very informative videos

[@just4therecord]

Can this power pack connect to a smartphone so I can read how much charge it has etc like on Blackvue power magic pack? If not then how can I tell how much charge it has?

[@annettejoseph4127]

It cannot as there is no app for it.

[@DuoMaxwell007]

What if your fuses are in the trunk?

[@paul132]

Hi I had a question... Do you just take the hardwire from the dash am and connect that to the battery hardwire kit? Do I just ignore what you did in the first video when you just installed the dash cam without the battery??

[@dial2fast]

Yes that is correct. If you buying the battery pack, then just connect the dashcam power wire directly to the battery pack.

[@paul132]

@@dial2fast thank you for the info, great video!!

[@richeyrich6855]

@@dial2fast Thank you, Sir! I was wondering the same thing. I'm doing a new install from the start so I now know to skip the hardwiring of the dashcam directly to the fuse box because I will be installing it directly to the battery pack which will give me the full function of the parking mode. Thanks again!

[@Califas2014]

Where is the socket cigarrete charger ?

[@ntsesyaj9996]

Why do you use the 10 volt from the fuse box? I notice the other guy in another video used the 20 volt from the fuse box.

[@dial2fast]

I believe you are asking about the 10A fuse (and not 10 volt). The fuse rating is in amperage which is the current draw. If you hardwire the charge cable to the fuse box, the maximum current draw to charge the Thinknware battery is 7 amps. This is why I tapped a 10 amp fuse because you want to use a fuse that is rated higher than the 7 amps. This also means a 20 amp fuse will also work. Having said that, you don't want to tap a 5 amp fuse to charge the battery because that circuit will not supply enough current.

[@ZNavy]

@@dial2fast Hi, just to clarify iVOLT BAB-50 Battery Pack comes with set of 20 amp fuses, please correct me if I'm wrong, but my understanding was that the fuse that you pull out of the fuse panel/box must be same or grater amps as accessory (external battery in this case). The reason I'm asking this because I'm not sure should I tap this battery to 15 amp fuse (in my car that would be a cigarette lighter circuit) 20 amp fuse (in my car that would be a heated seats)?

[@dial2fast]

@@ZNavy The fuse rating you are looking for in the car should always be higher than the device current draw rating. In this case the device being the BAB-50 draws 7amp max. So you can tap a 15A circuit or a 20A circuit. Even though the BAB-50 comes with a 20A fuse, that just happens to be the fuse they include. They could have included a 10A or 15A fuse and that will still work. The original fuse from your fuse box will go into the bottom slot of the fuse tap and therefore retain the original circuit in the vehicle. Since the BAB-50 comes with a 20A fuse, you will place that fuse in the top slot, and this 20A fuse will be the one to provide current to the BAB-50. Technically, you can put a 10A or a 15A fuse in the top slot of the fuse tap and that will still work fine. But you cannot put a 5A fuse in the top slot because the 7A will exceed the 5A and blow the fuse. In your example, you are perfectly fine to tap the 15A cigarette lighter fuse.

[@ZNavy]

@@dial2fast Thank you for your fast reply and your detail explanation. I wish they would use lower then 20 amp fuse in IMHO this would create less confusion.

[@richeyrich6855]

@@dial2fast Thank you!

[@craigweston5887]

It takes 45 mins of driving every day to full charge the battery pack, so for people like me who only live 5 mins from work it was a waste of money. They should have had the option of plugging it into the mains at home. I only got 5 hours on my 2 ch U1000 today.. tomorrow I will get less.

[@richiebennett161]

Hi can you tell me what happens when the iVOLT battery runs out will the system start using the car battery? Many thanks

[@dial2fast]

Once the iVolt drain to a very low level, it will stop outputting voltage to the dashcam and the dashcam will be powered off. It does not drain the car battery.

[@richiebennett161]

dial2fast thank you

[@lloydd7202]

Hi, is this compatible on a any brand of dashcam

[@dial2fast]

It will work with any dashcam where the power cable uses Ignition 12V and Constant 12V power.

[@lloydd7202]

@@dial2fast perfect, this is almost the same as the ivolt mini?

[@5abigabroo792]

How much?

[@suzytsaab388]

Can l use an OBD to install the battery?

[@dial2fast]

If you mean power with OBD, then the answer is no.

[@wanditisna]

👍👍nice bro

[@s4yfur123]

Can this charge via the obd

[@dial2fast]

No

[@faisalrkhawaja]

Boo! Thinkware should go USB, which would allow any third party power supply.

[@MrCrazy-R]

main fuse needto be atleast 10 amp?

[@dial2fast]

Yes you need 10A fuse to tap from. The High charging current of the battery is 7A.

[@MrCrazy-R]

@@dial2fast and the fuse from the ivolt always need to be on the top by the cable?

[@dial2fast]

@@MrCrazy-R Yes put the iVolt fuse on the top slot on the fuse tap.

[@MrCrazy-R]

@@dial2fast i have 1 last question, ash long you put the ivolt fuse on the top it dont matter what fush from the car go in i mean if u put it in a 5 amp slot or 7.5 it will never break the fush only u battery wont charge on max speed?

[@MrCrazy-R]

i have to know this because im running out extra fuses for now, and my car have only 2 fuses i can use in the dashboard the rest are in the engine bay, sorry for my not american english im from the nederlands 😂