Video helped me make my wife think I knew exactly what I was doing thank you
@MrOlskool882 жыл бұрын
lol
@stevecraven29563 жыл бұрын
I watched this video this morning and installed the doors this afternoon. Delta has good instructions but this is a great video and definitely worth the time to watch it! I recommend that anyone doing this job get a diamond-tipped bit if you are drilling porcelain tile, they are worth the extra cost. If you are not good with a diamond-tipped bit cut yourself a templated from a piece of plywood or watch a video on how to use one and practice on some scrap tile or you may damage your tile. Also, the Delta instructions that were in my package say drill a 3/16 hole in the tile but that is not correct it is 5/16, hopefully, they have corrected that in the instruction book.
@ubb4me Жыл бұрын
Do you have the Delta model number and where you bought it? I need to replace my old shower doors. Thanks.
@shebeme2000 Жыл бұрын
Great, easy to follow video. I had a very similar Delta door "professionally" installed last year but the doors are very wobbly when you slide them. It's very loud and annoying, I feel like I'm risking breaking the glass .
@amr254 Жыл бұрын
Do you know if it was attached to a stud?
@shebeme2000 Жыл бұрын
@@amr254 yes, so was the previous one.
@ValentineDayTwin4 жыл бұрын
For ones that are not really good on a neat caulking job, create a channel for the caulk to be applied with two strips of painters tape at desired width. Remove the tape after the caulk becomes fairly firm BUT HAS NOT CURED COMPLETELY. This will minimize any "ripping " of the caulk's edges and give a nice clean uniform appearance. Tape removal after the caulk has cured completely might result in a " jagged ripped " looking appearance.
@robrero Жыл бұрын
So, I keep on getting ridges when i pull the tape....are you saying that this is a symptom of pulling the tape too soon? I'm at the end stages of a bathroom renovation and caulking has been frustrating
@joaquinsuarez6090 Жыл бұрын
@@robrero After you put tape and applied silicon use your finger to push silicon, then remove the tape right away, clean your finger and use it again on silicon to make it smooth and remove lines of silicon left with tape. If you don't do that you will end up with 2 higher lines of silicon, one on each side.
@daviddetrick97063 жыл бұрын
Thank you very much my friend. Delta did not provide any instructions. Without your help I wouldn't have been able to install the doors
@davidmuniz8177 Жыл бұрын
Wow! Wonderfully made video on how to install sliding shower doors! You were very detailed and clear on how to install each component. After watching your video, which I thank you for taking the time to put together, I now feel confident about installing it myself. Thanks again for your informative video. I really appreciate it!
@Zidanemoggy2 жыл бұрын
Great video! Caulking tip for DIYers: buy an electric caulking tool. They are worth every penny.
@ericgaida98682 жыл бұрын
My door did not come with written instructions. You video was great, it worked perfect for me. Thank you for going slowly.
@christopherzimmer4 жыл бұрын
Phenomenal video editing! Thank you so much- very helpful-- detailed enough to provide added value, but not annoyingly slow!
@jonsollenbergerjr.57853 жыл бұрын
Wow I watch a lot of how to videos but this one just amazes me. Great work. I absolutely loved watching this and it put my mind to ease on the installation process.
@jungletension28352 жыл бұрын
I watched your video several times before installing my shower doors I added two screws at the top rail at either end though and I added a 3-inch screw into my sill beneath the door guides on the bottom rail
@kalpersaud91322 жыл бұрын
Great video, I will be using this to install the same shower in my bathroom this weekend, very detailed video great job.
@wessboucher84422 жыл бұрын
Very good layout, step by step, easy installation.
@jovantasevski51574 жыл бұрын
Thanks for the video. I am in the middle of the installation process and I am a little bit worried about the bottom track not being secured to the curb of the shower. The installation guide doesn't include any screw to fix the bottom track and I don't feel comfortable relying only on the silicon applied in the channel under it. In your video (9:47) one can also see that the bottom track is kind of wobbling up and down. It moves up and down as you press on it. Putting just silicon at the edges will keep the track steady and it won't be enough to stop water entering under the track. I believe that this is why a lot of customers in their reviews are complaining about water splashing out of the shower. Honestly, I am thinking of putting at least two screws through the track into the curb to make it stable and prevent any gaps between the track and the tiles of the curb. My curb is made out of concrete bricks so there shouldn't be any damage if moisture gets through the screws. Your opinion?
@kalpersaud91322 жыл бұрын
If you silicon the base track on both side it will be enough to hold it
@joaquinsuarez6090 Жыл бұрын
Good idea, you can fill holes with lots of silicon before putting the screws, that way water doesn't get inside bricks.
@Mike-ls1tx3 жыл бұрын
I had mine installed by a contractor and it leaks, I love the shower but there is nothing that keeps it from running under to glass to the outside of frame what am i missing he said he caulked it
@Airam_Legnar Жыл бұрын
Great video, only one thing missing. Make sure the surface is leveled....
@artsoto54593 жыл бұрын
Excellent video, does the holes have ro hit the studs? Is the tile strong enough to hold the door
@stormbytes Жыл бұрын
Terrific job! Thank you for sharing this video!
@leec86774 жыл бұрын
Great video. That helped a lot. Thank you. I used a hack saw and miter box on mine. Cutting the top bar was a nightmare. Next time will definitely purchase an angle grinder and diamond blade.
@jachmoodyable Жыл бұрын
Excellent video !
@maheshpatel34954 жыл бұрын
That looks like a nice professional installation.
@DanOfMostTrades4 жыл бұрын
Great video! Thank you for all of the close-ups and explanations.
@Mike-ro3ql3 жыл бұрын
thanks buddy that was far better then using the paper instructions
@mayfernandez21153 жыл бұрын
Excellent, very simple video the way you explain it, thank you for the help.
@losmentadosderichmond689 Жыл бұрын
Thank you for this video help me a lot
@joaquinsuarez6090 Жыл бұрын
Great info, thanks. What model number is that door?
@lauracorratti91892 жыл бұрын
Thank you, did it just the way you did ,very helpful.
@gabogabrich2 жыл бұрын
Thank you very much, your video helped me a lot
@albertz39404 жыл бұрын
When showering does it matter if the outside door is closed towards the shower head or the other end in regards to water exiting the shower? Or does it not matter which way any door is closed during showering?
@milfordcollins88924 жыл бұрын
Yes it matters. The inside door needs to be towards the shower head. The water needs to run off one door and overlap onto the next door. If they are in the wrong order water will shoot between the two doors.
@bhappy88922 жыл бұрын
Just this installed by a ( handyman ). First the door had a gap on both sides when fully open, the gap gets wider towards the middle and even more at the bottom. He adjusted it, but now the door doesn't stay shut and slides open, leaving a gap at both ends. Any suggestions on what he did wrong!
@kelvinmurphy97042 жыл бұрын
Great instructional video! Where did you buy your drill bit? It seemed to drill through the tile effortless.
@ToolsReview2 жыл бұрын
Thank you! amzn.to/3LWleL7
@emmanuel78992 жыл бұрын
Thank you
@addys27003 жыл бұрын
Great .!!! Thank you so much .
@jasonandmichellec.50512 жыл бұрын
Is this the dude from "No country for old men"?
@davidrojas53053 жыл бұрын
thanks. with this video i installed the shower door
@andrewilks83152 жыл бұрын
Great video mate!!!
@marennyalarcon97512 жыл бұрын
Great video, can you please lest the laser level you used?
@ToolsReview2 жыл бұрын
Here is the link, not a sponsor and I paid full retail on the laser. It demands batteries but works well: Huepar 902CG Self-Leveling 360-Degree Cross Line Laser Level with Pulse Mode, Switchable Horizontal and Vertical Green Beam Laser Tool, Magnetic Pivoting Base Included www.amazon.com/dp/B074XX1DTC/ref=cm_sw_r_cp_api_glt_i_PTVCDTK9VV2K651KJ98C?_encoding=UTF8&psc=1
@marennyalarcon97512 жыл бұрын
Thaks.
@zdani252 жыл бұрын
Tks very helpful
@adanelicachavez84953 жыл бұрын
Nice job buddy
@delphinemcnielwilson2 жыл бұрын
how does the water get out of the bottom rail? this is the problem we are having with ours and the fact the builder did not put the doors on good either UGH!
@gregking43954 жыл бұрын
Thanks man this really home out a lot. 👍🏿👍🏿
@trueforum3784 жыл бұрын
Great video. Well done mahesh. I want add one important point: drilling tile is very difficult with normal drill. Please use high impact high RPM hammer drill and those holes become easy. Thank you!
@dablet2 жыл бұрын
wish you had shown how to mount the mirror onto the frame
@louieharo92403 жыл бұрын
I did everything the way the instructions that came with the shower doors and your video and the inside glass door is hitting at the bottom corner on the metal frame
@asessino234 жыл бұрын
Thank you you save my life today
@cashnaftzger6348 Жыл бұрын
My Handels hit each other while opening.. any advice
@A9K33 жыл бұрын
Tips on cutting off the top rail? I want to get the same cut off tool. Will a diamond wheel be best to cut? Surprised there were no sparks
@ToolsReview3 жыл бұрын
Good question, I used this cutting wheel - not a sponsor: 3 in. Metal Cut Off Wheel (3-Pack) www.homedepot.com/p/306599198
@ryantfinchum3 жыл бұрын
I used a 32TPI hack saw... Works just fine
@that_juan_sti50543 жыл бұрын
Very well detailed video 🙏👍
@tubernery4 жыл бұрын
Do these doors or top rack include rollers? This was the only piece I didn't see. Thank you.
@ryantfinchum3 жыл бұрын
Yes they come with the glass doors
@ToolsReview4 жыл бұрын
Please subscribe to help me get to 1,000 subscriber. Thank YOU!
@BrianSmith-fn3rl3 жыл бұрын
Nice job!
@AlbertZoAlonso2 жыл бұрын
Thanks for the video, the bottom base rail should also have caulking which will help secure that rail a little more to the floor. Otherwise it will move on the one side like shown in the video. The glass also has a particular side which goes in and out, as well as that wheel slide attached to the glass.
@ShadowFireCoolDude3 жыл бұрын
Very good & handy man!
@justdissin73403 жыл бұрын
What kind of drill you got cause me takes me for ever to drill through tiles
@carolinacisneros2263 жыл бұрын
Thank you this really helped
@louisbrecheen72433 жыл бұрын
Thank you. This helped a lot.
@Nicetime-nc7zn Жыл бұрын
How to get it back on the delta if it comes off ?
@zemzem83234 жыл бұрын
Thank you, great video, helped me out big time!
@kevinsetchfield2019 Жыл бұрын
That invisible coating should be facing into the shower as it shows on the stickers, I see a lot of people not paying attention
@mariaareyna5374 жыл бұрын
Gracias . Roberto el paso tx.
@kmccb234 жыл бұрын
What laser is that? Thanks
@princediesel13 жыл бұрын
Which door do you use to come out of the shower ? 😳
@djsutton39902 жыл бұрын
Door Leaks @ the bottom near the by pass door base
@daciannwalker19372 жыл бұрын
Umm how much to buy it
@bartolomeoserrano93942 жыл бұрын
Hi if i have 55"W shower what size it have to be the door?
@dennismadigan2023 Жыл бұрын
Does any one know the difference between the Delta Simplicity and the Lyndall model?
@joeljacobs44683 жыл бұрын
Thanks very helpful
@marshmanmusings97894 жыл бұрын
Very nice video. Thank you!
@goneviral60374 жыл бұрын
Great video! Thanks
@jaszzy26 Жыл бұрын
Is it frameless shower door?
@ToolsReview Жыл бұрын
Not this model
@Mateo312794 жыл бұрын
Good tutorial video. Thanks
@jonn5192 жыл бұрын
Do we put silicone on the side rails?
@ToolsReview2 жыл бұрын
I did
@2013bayy4 жыл бұрын
This really helped me install my door! Thank you!
@linhvnguyen3 жыл бұрын
Please give me the link to the brand or kind of laser level you used
@ToolsReview3 жыл бұрын
Not sponsored. It consumes batteries faster than I expected but it worked well. Huepar 902CG Self-Leveling 360-Degree Cross Line Laser Level with Pulse Mode, Switchable Horizontal and Vertical Green Beam Laser Tool, Magnetic Pivoting Base Included www.amazon.com/dp/B074XX1DTC/ref=cm_sw_r_cp_api_glt_fabc_3D2YXN5A3G0QRX16RNJP?_encoding=UTF8&psc=1
@linhvnguyen3 жыл бұрын
@@ToolsReview thank you very much
@vacationtime-zp3rc2 жыл бұрын
Sir Tell me height measurement please
@FIRST-x4h2 жыл бұрын
Hello. What lazer level did you use?
@ToolsReview2 жыл бұрын
amzn.to/3tPD8Y6
@wekiyajunk41392 жыл бұрын
The video is not detailed enough. Some of the essential steps were overlooked.
@daveortwine26412 жыл бұрын
That sucks you had to drill the pilot holes through the frames. As much as they're charging for these, delta should be putting the holes in them. That's a joke. The one I did for my parents had them predrilled
@Gustamachio Жыл бұрын
The handles are so loose and floppy no matter how you adjust them :(
@blk19682 жыл бұрын
Whoever installed this in my building must have watched this video because he didn't use a level and is so far off changing roller position doesn't help.
@truett443 жыл бұрын
You did all this work and forgot the most important part is hanging the two doors without breaking them . ??
@Clarkcanepa3 жыл бұрын
Quite frustrating
@mikezieg802 жыл бұрын
Laser light. Give me a break.
@rwkrauss60542 жыл бұрын
Darn little to none instructions on attaching the bottom track to the shower pan. No screw holes are in the bottom track molding, so i'm guessing that you lay a bead calk to stick this track to the shower pan??? For this reason i give this video a minus rating!
@jeffyoung13612 жыл бұрын
crap job on that sill. spend the c-note and do that better