how to create, transmitter and receiver control circuit , jlcpcb

[@FilamentFriday]

How did this work? Your momentary switches are soldered wrong. You are shorting the switch the way you positioned them on the board.

[@inventorkr1]

This mistake is intended to arouse the viewer's attention. I salute you for noticing and watching the video carefully

[@FilamentFriday]

I see you cut one of the leads on each switch later when operating it.

[@BadroHulagin]

Автору респект и уважение, все гениально и просто для тех у кого руки из нужных мест и голова не из сена

[@xminusone1]

I agree with you. There's so many things you can do yourself when you think and are not afraid of trying.

[@chideraagbasiere7868]

Beautiful video, this work is brilliantly simplified. Brother please, how can I make it 6 channels instead of 5?

[@MiguelDeMarchena]

ht12d and ht12e are only 4 channels and the ones you show here are 5 channels so why not combine to have 9 channels to control more complex remote control toy like a tank or a rc robot with cam and robotic arm

[@ASP29Tech]

On this video is not ht12d and 12e,but ic Tx dab RX2b,IC that is usually used by old rc toys

[@MiguelDeMarchena]

@@ASP29Tech combining ht-12 ics with rx and tx 2b and maybe (pt2272,pt2262) we can get up to 14 chnls,old rc toys or daily appliances no difference

[@gabrielevangelista7025]

instead of buttons I can for example put analog signal inputs to be transmitted to the receiver?

[@Icannedsoup]

I use a used PCB. And... HOLY SHIT MAN I SCRATCHED THE PCB AND MY CUTTER KEPT BROKING

[@venkatramanj8978]

This circuit is use for home lights switched off and on?

[@briantclydeaquino5157]

What voltage are you running it with?

[@xminusone1]

Are you using the toner transfer to make the pcb? You know with a lazer printer?

[@junaidtp9815]

i make an ht12d&ht12e rf circuite using 433 mhz module..My Circuit Is Working Fine(Wired Condition_Data Connected to data Pin) But when i connect RF(Transmitter And Receiver), Led Glowing Continuously (Even When I disconnect Transmitter) ...when i press swich on in transmitter led off in reciver why this?

[@inventorkr1]

Check the electronic components you used.

[@simpleprojects6364]

I was confused with the switches, a and b terminals were soldered in same line

[@chideraagbasiere7868]

brother the push button switches are soldered wrongly! How did this even work?

[@mecatx]

Great video. How about positing a simple bill of materials. for all parts Thanks.

[@gafurjabborov9524]

Радио предедачик игрушки машина спасибо большое красивые видио понравился ваш видио.,

[@kamleshchavan7451]

Can you make a video explaining the working and how the data is transmitted from transmitter to receiver , of the transmitter and receiver module you have used in your project

[@kamleshchavan7451]

Can you make a video

[@AleksandrMalinov666]

После запайки кнопок не той стороной уже желание смотреть дальше отпадает

[@venkatramanj8978]

How long this remote will work?

[@inventorkr1]

200m

[@VietNam.2024]

Video hay quá thích hợp cho người mê điện tử...

[@julesdelarosa5675]

can I use tx 2b 1120y in this diagram?

[@nazificin8014]

define alan tarama cihazına degerli metaller icin ikaz lambası veya ikaz verici takabilirmiyiz

[@inventorkr1]

you can

[@nazificin8014]

bu konuda yardımci olurmusunuz

[@IvanKnavI]

Автор, рекламируешь jlcpcb, даже в название вынес,а сам паяешь на самодельной плате третьесортного качества. НепОрядОк...

[@gualtierorossi4856]

can I ask you what is the name of the green card where you attach the two motors?

[@inventorkr1]

RF 433 mhz

[@SRelectric]

Super project 👍

[@tntomega]

i love this project i use ht12e and ht12d but i dont love the range its maximum 100 meter how i make it long range like 1 kilometer?

[@NotWhatButWho]

Hey, very cool video. Is there any way to set up sticks instead of buttons to this set up? Including the smooth input, rather than a on/off signal

[@soransorany4137]

That countrol for haw long meter?

[@esneyderlizarazo8622]

Does the transmitter use 12 volts?

[@John_Smile]

Thanks for the description. I want to build a buzzer/ring, "bing-bang" with a radius of 30-50 m. I will look for the products in the place indicated by you . Thanks !

[@jimmyzea8760]

how do you make those pcb;s?

[@inventorkr1]

You can remove the copper layer through a liquid substance called iron chloride

[@hmoobqaumteb7596]

ສະບາຍດີ ເຂົ້າສາມາດບອກຂ້ອຍໄດ້ວ່າໄຟໜ້າປັດຂອງລົດclick i 125 ຂອງຂ້ອຍບໍ່ເຫັນຮຸ່ງແມ່ນຍ້ອນສາເຫດຫຍັງ?

[@فرفشمعنا-ح3ق]

Please what is the number of the integrated circuit on the transmitter board?

[@inventorkr1]

All information and details can be found through the link below the video in the description box. 2B-TX

[@Spookieham]

Adds relay sound but there are no relays. Antennas on receive and transmit boards are not the same length.

[@ungkaphutasoit928]

hy ,thank you for great video,but i want ask you about the ic ,can it replace by another component?

[@Thamer03]

How many range transmitting

[@jfom1431]

2 meters

[@ramkrishnabal5445]

2mtrs range is very short, 1KM Range may applied for one floor to another!

[@inventorkr1]

200 _ 800 m

[@Thamer03]

@@inventorkr1 Wow amazing

[@islomjon_akramov2000]

Best,Clas,God,Perfect,Alo,Маладец

[@yakup2546]

where can we find these parts and board characters. could you send it to us?

[@inventorkr1]

inventor-kr-tools.com/

[@tnamen1307]

@@inventorkr1 please kindly look into my request. I'm your new subscriber.

[@neihsangapautu9096]

Can we transmit audio signal using that

[@inventorkr1]

yes

[@bagusbagus3083]

Button can use arduino joystick?

[@Ma_X64]

Это особый дар -- делать всё максимально всрато, но чтобы при этом получалась збс 😂

[@borisraskolnikov]

Бывает делаешь красиво, платки там заказываешь, отлаживаешь по пол года, потом напаял - не работает)

[@Ma_X64]

@@borisraskolnikov Вот! Именно!)

[@___Loki___018]

What for the range..?

[@skylai82]

is this possible transmit high frequency？

[@skylai82]

Around 10Mhz

[@inventorkr1]

Yes, you can transmit up to 27MHz

[@ParmarYashpal98]

GOOD WORK PCB CARQET

[@subarnachakraborty6960]

If i press all the key at a time, will all LED glow?

[@inventorkr1]

YES

[@Russkiy_medvejonok]

Я повторил схему и всё заработало, попытался подключить мотор через драйвер l293d , но мотор не заработал, решил повысить напряжение до 8 вольт, но приёмник отказался принимать сигнал, что я делаю не так?

[@ferrumignis]

Why are yoy surface mounting through hole components?

[@munnakumarsingh2334]

CRO operate krne k liye vidio bnaye sir .....how to operate CRO????

[@Mitreview86]

Can you make AM circuit?

[@VictorLarsen-fy9ls]

Это такие платы от JLCPCB ? 😆

[@j0nikus]

Я тоже об этом подумал))

[@ShekharParab]

Price kya hai

[@jean-lucjla2987]

Pourriez-vous nous donner la portée de votre montage ? Merci

[@xminusone1]

C'est écrit dans la description. Il opère a 433 MHZ et a une portée de 200 mètres dans de bonnes conditions. C'est pas très puissant mais il serait très facile de faire le PCB avec une imprimante lazer et la méthode de transfert de toner avec la chaleur. C'est très simple et facile. J'ai construit plusieurs projets avec cette méthode et c'est très efficace. J'espère que ma réponse est utile. Je n'ai jamais eu besoin d'utiliser le gadget pour brasser le pcb, juste utiliser un plat de plastique avec un bain marie pour que le chlorure de fer sois légèrement chaud et ça fonctionne très bien. Il y a plusieurs tutoriels en ligne.

[@elsayedhassen8603]

لازم قطعتين من هذة النوعيه للتردد

[@masbeben]

minta skema rangkaiannya bang

[@frankchang436]

How long can transmited?

[@inventorkr1]

200m

[@frankchang436]

@@inventorkr1 Thank you.

[@Alex-fh2th]

Какая микросхема применяется для щифратора и дешифратора сигналов...?

[@АлександрАнтонов-щ1в]

Такие стоят в китайских радиоуправляемых игрушках. Что-то типа RX-2 и TX-2.. Возможно есть а Али...

[@mohammadkaish6134]

Mosquito killer circuit ka video banaye plz

[@ZAFERYILDIZ52]

👉❤️

[@inventorkr1]

❤️

[@MINERBOY676]

Can you give Gerber file please

[@Garganella_g]

На какое расстояние работает установка?

[@electroniquepassion]

👍❤️❤️❤️👏👏👋

[@inventorkr1]

️❤️❤️

[@waustonsidnei7028]

Me manda o circuito eletrônico com as peças

[@ВладЧе-ю4х]

Как ОНО будет работать если все кнопки закорочены.?Смотри даташит на кнопки.

[@mitaibaka9655]

Bos puwe b ako mag pa assemble po sanyo

[@San_DIY]

Please make wireless microphone transmitter and receiver

[@tnamen1307]

Super genius 👍👍👍

[@cahyamega3333]

Pake ic apa yah?

[@tnamen1307]

Sir can I request one similar project. Say, a vibrator sensor which is installed in a car will send warning signals to the remote key. The remote key is to be modified to work as both transmitter and receiver. Upon receiving the signals from the car, there must be some vibration in the keys to warn the owner's from theft. Presently, any car keys works only one way as Transmitter. 😇😇😇

[@vighneshnyk1695]

Connect vibration sensor in place of switch

[@DorperSystems]

The pub is clearly hand drawn with a sharpie and etched with fecl why are you advertising a pcb fab?

[@Андрей-ф1ф4ы]

Что за паяльник, тоже хочу такой

[@cheatlauncher7208]

Evil morty moment :D

[@ahmadaslam7946]

Where are you from...?

[@СергейЧучалин-ъ5д]

Паяльник великоват для этого

[@atharvthakare2332]

PCB making tutorial video pls

[@LeonelAugusto-j6s]

Continuem assim.

[@ZoneChannel001]

Bang tolong bikinin tutorial membuat inverter mini dari DC/single suply jadi CT/Simetris 🙏🙏

[@Mr.liakatHossain-ct5dc]

I have need this transmitterr and reciver circuit component. I am bangladeshi. I dont know english.pelec trying give me. Total 4 pes.thanks.

[@viktorkarlsohn3705]

Cheap== inexpensive [low cost] & low quality; Use: high quality, low cost

[@Rajendrasingh-ce2er]

How much range

[@inventorkr1]

200m

[@user-iy7rj3jr8m]

дальность какая ?

[@inventorkr1]

200 m

[@LinhPham-jm1gj]

Sư phụ hàn độc quá chỉ đệ với

[@APPLEX10M67]

Sir. Make a project using phone PFO ic

[@MrDricooh]

How much if someone make this for me?

[@serg7486]

Как создать схему ретранслятора ТВ сигнала?

[@АлександрАнтонов-щ1в]

Ретранслятора ? Принять и перебросить ? Или имеется ввиду видео пустить в эфир ?

[@ValeriyDvoreckiy]

Ретранслятор это принять и передать!

[@San_DIY]

Amazing 🤘

[@ibadqori4909]

Luar biasa bos

[@alexsotnik5950]

Great job ! Amazing! Would be nice to have website with a full desciption of the project.

[@LeonelAugusto-j6s]

Altamente qualificados.

[@safakozer4687]

Devrede kullanılan entegre, ucuz uzaktan kumandalı arabalarda kullanılan entegre olup diğer entegrelerden etkilenir.

[@inventorkr1]

200m

[@AbdulRafay-gv5ev]

diagram please

[@inventorkr1]

You can find the link in the description

[@mithunsharma3497]

Operator pcb chahiye

[@Desiludido79]

Todas as microcheves estão erradas!!! Erro!!

[@hendarservice4944]

Koreksi aja,jika pasang tombol switch nya seperti itu tidak akan bekerja 🙏👍👍

[@inventorkr1]

yes

[@processing449]

good

[@jozefnovak7750]

Super! Thank you very much!

[@sumarnosumarno5982]

Mendingan beli jadi.. Ini sih cuma disuruh liat nih , saya lagi bikin..

[@ElectronicFanArm]

❤❤❤

[@youtubetv7000]

SUPER

[@pojokkampung99]

Sekema rangkaian tidak di publikasikan....

[@RayS-zh5we]

Great video 📹 👍 thanks for sharing 🙏😇😎

[@K-poplife701]

0:51

[@K-poplife701]

1:28