iPhone SE 1st Gen screen replacement/digitizer glass and LCD re-installation instructions

Рет қаралды 4,231

3 жыл бұрын

www.LaptopScreen.com
www.laptopscreen.com/English/...
step by step detailed guide on iPhone SE 1st Generation disassembly and reassembly and screen replacement (front assembly: LCD, Glass Digitizer, Frame)
This is a guide on reinstalling the front assembly on the Apple iPhone SE 1st gen.
For the reinstallation process we will need the following tools:
- Pentalobe Screwdriver
- Suction cup
- Plastic pick
- Phillips Screwdriver
The front assembly contains the frame, the glass digitizer and the LCD screen. You will need to replace the entire front assembly if any of these components are broken.
Turn the phone off by holding the power button and confirming the shut down on screen.
Remove two screws on the bottom of the phone with a pentalobe screwdriver. Set the screws aside.
Place a suction cup just above the home button. Pull on the suction cup and insert a plastic pick between the front assembly and the main body.
Gently move the plastic pick along the bottom edge, separating the front assembly off the main body. Once separation is achieved
open the screen to about 30 degrees.
The home button fingerprint sensor connector needs to be undone before the phone can be opened fully. Using a plastic pick open the securing bracket over the connector and disconnect the fingerprint sensor.
For a safe reinstallation process we need to disconnect the battery. The battery connector is located under a small metal shield. Hold the front assembly vertically and remove the two phillips screws holding the shield in place. Remove the metal shield. Disconnect the battery.
In order to separate the front assembly from the main body we need to gain access to its connectors under an EM shield. Remove the four phillips screws while holding the front assembly at a right angle to the main body. Remove the EM shield. Set the shield aside. Next step is to open the threesmall connectors. Use a plastic pick and gently open the connectors one by one.
Separate the front assembly and place it on the desk. Some components need to be transferred from the original part onto the new assembly. Namely: The big metal shield, home button, front camera with light sensor and speaker.
We will start with the home button. Remove three phillips screws, one on the home button cable and two more on the home button bracket. Set the bracket aside.
Using a plastic pick carefully separate the home button cable off its adhesive pad. Pick up the assembly and apply some pressure to the home button from the front. Use a plastic to help separate the rubber gasket, set the home button aside.
Remove three phillips screws holding the speaker bracket at the top. Pick open the bracket together with the speaker and set it aside.
Proceed on removing the big metal shield. Remove two phillips screws on the right side, then two more on the left side.
Pick up the metal shield from the bottom and carefully lift it up. The sensors are grounded to the metal shield with conductive tape. Pick off the sensors from the adhesive pad near the speaker contacts and carefully lift the metal shield together with the sensors, set them aside.
Place the new screen on the desk and replace the big metal shield. Carefully guide all the sensors in their appropriate positions. Secure the metal shield with two phillips screws on one side and two mor eont he other side. Replace the speaker. Clip in the speaker bracket on the left side then push down on the right side. Replace three phillips screws, the longest one goes at the top of the speaker.
Replace the home button onto the new display assembly. Cover the home button with the metal shield and secure it with two phillips screws.
Theres a tiny contact pad that is mounted on the third phillips screw that was left on the home button cable. It need to be positioned underneath the cable on reassembly and secured with a phillips screw.
Now we can connect the front assembly to the main body. Position the front assembly at a right angle to the main body aligning it to the top edge of the phone.
Hold the assembly vertically and gently snap in all three connectors.
CAUTION! It is very important not to force any of the connectors. All connectors are very fragile.
At this point we can test the device. Reconnect the battery, and turn the phone on, if the start up graphics appears the replacement part is installed correctly.
Hold the power button to turn the phone off, and confirm the shut down on screen. Replace the metal shield and secure it with four phillips screws.
Replace another small metal shield covering the battery connector; secure it with two phillips screws.
Reconnect the fingerprint sensor. Replace the small connector bracket over top.
Close the phone starting at the top and gently squeeze around the perimeter until the front assembly snaps in place. Replace two pentalobe screws at the bottom.
and we are done!

Пікірлер: 13

@rodneystauffer18 3 жыл бұрын

I would love to have the iPhone to give it away to a family member

@Laptopscreen 3 жыл бұрын

Hi Rodney, thank you for being a subscriber! Your comment has been picked for the give away!!! Please get in-touch with us at www.LaptopScreen.com/support/ with-in 10 days to claim your prize :) You will need to register an account and provide your shipping address there. Kelvinxj is the second pick, in-case Rodney doesn't contact us by Dec 12, 2020.

@rodneystauffer18 3 жыл бұрын

@@Laptopscreen I sent you a message

@rodneystauffer18 3 жыл бұрын

This is awesome that I won! I will put the phone to good use

@cubegaming1941 3 жыл бұрын

Nice video, I plan on giving it away, to one of my siblings, I they don’t want it ima give it to a friend

@krystalb2205 3 жыл бұрын

Have been a fan of you guys for a lot of years now. Many people come into my shop in different situations, many are need but do not have the funds to repair or purchase a device. I would choose someone who is really in need to receive this phone and give it away.

@filipevieira5971 3 жыл бұрын

Nice video, thanks! As for the iPhone SE 1st Gen, I would give it to my mom because she needs a new phone, and this would be a wonderful Christmas gift for her! She would be really happy with it! Thank you!