Is best solution? Fixing bubbles on Uconnect 8.4

Fixing the bubble problem in Uconnect 8.4 in the 2017 Dodge Challenger.
This is the cheapest solution but not the best, it is more correct to replace the screen with the current version without the bubble problem.
Part number actual version LSD with Touchscreen LA084X01 (SL) (03)
You will need:
Isopropyl alcohol
Double sided tape at least 1mm thick
Lots of tissues
And a lot of time
All this will cost you less than $20
What I don't like about this solution is that it leaves small marks on the touchscreen, which cannot be removed, they are visible at a certain angle when the screen is turned off.

[@LuxuryNation]

Just did this with my Chrysler screen. Took 45 minutes. Used double sided gorilla tape on the edge of the touch screen and my screen works brand new. Easy

[@_demon1k_]

You're welcome

[@LuxuryNation]

I did this before I seen ur video. But basically did it almost same way as you did. Good method

[@_demon1k_]

@@LuxuryNation I didn't like the matte look of the screen and the spots in certain light that can't be removed, so I decided to change the screen for a new one after all

[@talleyman8085]

Did this to my 2018 ram 2500. Unfortunately for me it didn’t last to long, maybe 3 weeks or so and it started ghost touching all over again. I didn’t want to buy a new screen but it got to that point. Found the newest model (SL03) and now back to normal. You would think a recall should have been done for this but I guess that makes to much sense.

[@_demon1k_]

Maybe the thickness of the tape you used was too thin

[@kennysdetroit]

Do you have the link of where you got the (SL03) replacement screen?

[@_demon1k_]

@@kennysdetroit check out this link www.ebay.com/itm/293468807390

[@killswitchh]

Agreed, it's also a safety hazard trying to get your audio to work while driving.

[@bobafittness1346]

How has the SL03 been holding up? Bought one of those for my challenger and wonder if it will last…

[@LOGICAL-JAY]

Is it necessary to remove the cars battery terminals before removing the radio to work on???

[@_demon1k_]

To remove the radio, either remove the battery terminal or remove the radio fuse in the trunk

[@MrPuroMichoacan13]

I just installed a new digitizer but the the touchscreen is not working? I double checked the ribbon connections, I used white double-sided Gorilla tape (didn't completely go around the screen just to make it easy in the future to remove). Any ideas/suggestions why it the touchscreen is not work?

[@_demon1k_]

If you replaced the original digitizer with a new one, the new digitizer might not be compatible with the device, but you shouldn't rule out a normal defective digitizer either.

[@MrPuroMichoacan13]

@@_demon1k_ Thank you...did you have to reset the stereo. I tried holding down the volume and tune button for 20-30 secs and nothing happened. BTW I have a 2018 Ram 1500 Ecodiesel.

[@_demon1k_]

@@MrPuroMichoacan13 No, I did not reset the system, I turned off the fuse before removing the uconnect

[@_demon1k_]

@@MrPuroMichoacan13 uconnect will pull the settings from bcm itself

[@HectorRivera-mf6ng]

Lol is it really taking this guy, that long to take off the Bezel😮

[@surgechicanos7591]

How long did it take to remove the screen

[@_demon1k_]

The hardest part is carefully removing the dashboard bezel. Cutting the touchscreen took about half an hour. The whole job took a few hours

[@christianmattia7740]

15 minute Job .

[@trewardon4167]

What tools do I need? Please respond fully brother!!!

[@_demon1k_]

Plastic spatulas, screwdriver, wire for glass separation cutting line, isopropyl alcohol, cotton rag and thick double-sided tape. And most importantly a lot of free time, the glue is a very long time to scrub

[@trewardon4167]

@@_demon1k_ thanks

[@trewardon4167]

@@_demon1k_ well I just fixed mines. Took me bout an hour an a half. I thank you so much once again!!! 🤚🏾high five lol

[@_demon1k_]

@@trewardon4167 Awesome, glad it worked out for you✋

[@robertoficarra6687]

Yesssssssssss

[@edwardestes4514]

How much do you charge for doing this

[@_demon1k_]

I don't do this commercially, it's a video for everyone to do it themselves, but I would recommend completely replacing the screen

[@jameskyle2238]

makes me wonder why they covered the whole screen with glue?

[@_demon1k_]

The screen and touchscreen are glued to improve image quality and reduce glare from light reflection, using an air layer between the screen and touchscreen appear additional glare, which for the radio in the car is not very good

[@jameskyle2238]

@@_demon1k_ ok, couldn't you put the tape all the way covering the screen? or would you not be able to see it then?

[@_demon1k_]

@@jameskyle2238 No, the glue between the screen and the touchscreen is special, it is in a semi-liquid state all the time and tape is not suitable for this purpose.

[@jameskyle2238]

@@_demon1k_ ok got ya on that. glad the dealer is replacing mine on the charger I just got.

[@christianmattia7740]

simple fix get the LG S2 the S1s are crap. just the screen. The old digitizer are crap and replacing it is a no go they are considered one part.

[@_demon1k_]

It is, but the price for a new screen is unreasonably high although it is a more correct solution to the problem.

[@christianmattia7740]

@@_demon1k_ I got a OEM S2 for almost 400$ but was worth it. The dealership will replace it for around 500 to 575$. The new screens updated have 5 yr warranty and are not made like the old ones where the glue between the digitizer and the screen have separated. The cost of a new radio is outrageous 750 to 1200 depending on who you go to. Its a rip off. Now if you haven't done anything to radio and it's delaminating you can always call up uniconnect and tell them that you have the old style radio that delaminating and they should open up a case where if you buy the part they will reimburse you. Remember uniconnect makes the radio not Dodge hope this helps. They should have done them recall on all the earlier version screens cuz they all delaminate it's common problem with Dodge Jeep and RAM products.

[@_demon1k_]

@@christianmattia7740 I agree, I also plan to replace

[@zmaninpgh]

@@christianmattia7740 I called U-connect today. I bought my 2018 jeep grand Cherokee four months ago in about a month ago. I started have errors asking if I want to change my clock time and it shows up all of the time and as soon as I press the X3 appears constantly. They told me since my vehicle has 86,000 miles on it even though it’s four years old, they will not replace it because of high miles. I told them it’s a safety hazard. It changes the radio stations while you’re driving and changes the heat temperatures and I said it’s a safety hazard. The guy said he will not replace it but he will put a note for further review, I said this should be a safety recall for these reasons, and I said other people are talking about class action lawsuits against, you guys and he told me they were for the information of the republican party to whoever may or may not give a damn

[@christianmattia7740]

@@zmaninpgh I agree it should have been recalled the old screens are crap I ended up getting a new radio because I had issues with the GPS card so if you're looking for a new screen let me know

[@alandln]

It look dirty!

[@_demon1k_]

It does, it takes a lot of time and wipes to clean off the glue between the touchscreen and the screen