2011-2016 Ford F250 Super Duty Factory Remote Start Installation No Dealer Required

[@tonyking3742]

Excellent video! Well done!! One tip for those with a 2016 Super Duty, the TPMS module is in the headliner behind the overhead console, not behind the glove box. You'll need to remove the drivers side visor, overhead console and grab handle to pull the liner down enough to access it. The antenna then gets 2 side taped to the headliner. Everything else in the video worked the same and same parts. Thanks!

[@JUSTINROLLER]

I don't have an overhead console.

[@chipjumper]

Those with the antenna mounted by the glove box can consider adding FL3Z-15K602-A which is merely just and extension cable to move the active antenna assembly to the headliner. The price just went up from $30 to $47 on TascaParts :(

[@jahillia]

any pictures or videos by chance? I have a 2016. Do I have to remove the entire overhead console in the middle?

[@michaelbaucom8220]

I have a 2016. 6.7 Superduty. Tpms is in headliner. I accessed it. Connected antennae. Programmed key. Enabled remote start on cluster and through forscan. Programmed keys. When keys are pressed the mirror lights turn off as of its starting then come back on but truck does not start.. Any idea?

[@gregwhitfield3149]

Just finished this on my brother-in-law’s ‘12 6.7......quick and easy and JUST like OEM !

[@brettmclean3113]

Oh and I had already bought the non ford key kit before I found your video. I guess time will tell on the quality of internal guts of the key. Thanks again! took less than 5 minutes for whole process.

[@spczippo556]

Oh My god, you sir a re a god send. I have a 2015 F350 as my work truck and i live in ND, and morning were quite cold, So i got an after market kit to install on my truck and that did not work because I did not have a second key for the truck, So the key i had made for the truck had the remote start button on it, and after the aftermarket kit still did not work i found your video looking for a different kit, and it works like a charm! I am going to get the antenna kit and an actual Ford Factory key here soon! thank you so much for your video!

[@Superduty_59]

Thanks you for the videos! I just programmed my new keys last week and my remote start today using Forscan. 2015 F550 6.7L works just like yours did. And yes since mine is a diesel it cycles the wait to start and then starts.

[@rscrubc300]

Did you use the same Forscan settings for your diesel?

[@DavidBradyTSP]

Just finished mine up today! You did a great job with this video, and took some fear out of the FORScan procedures. Only glitch I ran into was the 2016 putting the TPM module above the headliner instead of behind the glovebox. Appreciate you taking the time to put these videos together! Off to my next project...the cluster swap.

[@JackofAllMasterofNone]

Thanks for the nice comment

[@BreakerBreaker1320]

I do believe there is a longer cable for the 2016’s but I just used 3m up there and maybe get better range.

[@lateatday9826]

Where did you get a new cluster from?

[@drewharris1297]

This guy knows his stuff! Worked perfectly on my 2012 F350 6.7! Thank you!!

[@JackofAllMasterofNone]

Thank you

[@terrycarter8929]

I called my dealership and they charge $75 to hook up to the vehicle. I just purchased the OBD2 adapter and paid for the Forscan license. I had to erase the old keys and re program the new ones. I only got 1 key with the truck. Everything worked as you said it would on my 2011 F250 XL 6.2 flex. Thank you very much! Ill use the Forscan in the future for my collection of Fords lol

[@chrissmith-oq5nq]

How much was the license?

[@terrycarter8929]

@@chrissmith-oq5nq I thought it was $50 for 3 years but I just looked and it's $12 for 1 year. I guess they changed it.

[@functionxy]

This works without power locks?

[@terrycarter8929]

@functionxy not sure. I haven't seen too many vehicles without power locks in a while.

[@bill2001]

I bought my 2016 F250 and it came with only one key. my local Ford dealer quoted me $300 for just a new programmed key. Thanks for the vid

[@JackofAllMasterofNone]

That is absolutely ridiculous.

[@hckingoofed1399]

Mine wanted $400 cut and programmed

[@davidmontanez9066]

Ha ha Sewell Ford in Odessa TX wants 230(1hr) labor and 200-400 for the keys (1 or 2)🤡

[@travis1995100]

Thanks man just did this to my 2015 Ford F-250 6.7 diesel XL and the forscan program worked perfect

[@functionxy]

Did you have power locks? I don't and was wondering if this will work.

[@bassproable]

Thanks, just ordered the kit for my 16 F350.

[@ThatIsVicious]

How much was it?

[@BernieLehman-h4n]

This worked great, my 2016 F-250 had the TPMS moved up above the headliner so I didn't need the antenna.

[@rockwellb2]

Thanks! Bought a Ford Key and an antenna on eBay, had it programmed at the dealer for a cheap OEM remote starter for my 2011 6.7 F250 ! Works Great! 👌👍

[@haynlaskan9668]

Is there a delay to start for the diesel ?

[@Superduty_59]

@@haynlaskan9668 yes

[@grantmoening]

Need help! I have a 2012 Ford F-250 6.7 Powerstroke XLT. My truck already has the antenna (behind glove box like yours), the hood sensor, and the remote start is turned on in ForScan. Instead of buying Ford keys i bought the amazon special keys that had the best reviews (many reviews say their remote start works). Using ForScan, I programmed the keys, and all the buttons work great, except for the remote start button. My truck already has aftermarket remote start, but in order for it to work I have to carry around an extra smaller fob (it has ford logo on it, seems like it could be dealer installed, it also has an antenna mounted at the top if the windshield near the headliner inside the truck). The fob is annoying to carry around, so I'm trying to slim up my keys by adding remote start this way. I can't get the button to work! Need any advice you can give

[@mattearly1133]

I did this about three years ago on my 2016 F250. Had to hunt down the TPMS. Mine was in the headliner over the drivers side towards the front of the truck. A little more work but still a pretty easy "plug and play" install.

[@videom]

could you show a pic? I have an 2016 XL base model...not sure what I'm looking for.

[@OhYeahAboutThat]

Even though I don’t have a Super Duty ( I have a Ranger) I have really enjoyed this series.

[@rdatkins1]

This worked great for me. OEM remote start for less than an aftermarket one.

[@rscrubc300]

THANK YOU! I ordered from the link and everything was set up exactly like you said. Works perfect!! Thank you again

[@BreakerBreaker1320]

Perfect. This saved me from having to go to the dealer. What else can be activated in the dash that a 2016 XLT may have hiding in there? Got my key cut at Ace for $3.50 and had the kids scared because it was “one of those expensive chip keys” but it was fine.

[@thegmkiller1967]

If i have one oem key and one aftermarket key, both programed, can i still program 2 more oem keys?

[@willblackerby9055]

Worked on my 2015 F350 diesel XL Thanks for sharing this.

[@JackofAllMasterofNone]

Great to hear!

[@functionxy]

Do you have power locks? Was wondering if this worked without power locks.

[@Merescat]

Sweet another option to add to my 2015 F-250! and subbed! EDIT: used the part number to find a good deal on Ebay from a Ford parts house

[@michaelburtin3457]

Great video can you bypass the hood switch by unplugging it and will the remote starter still work

[@JackofAllMasterofNone]

I think the bcm has to have a grounded signal on the hood pin switch. So disconnecting it will not work.

[@star601]

dude, I just did this to my 2014 F250 and it worked perfectly. My buttons didn't work at first, but I did the 8 turning key procedure before doing the Forscan stuff. 1.Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition. 2.Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.) 3.Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5. 4.Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes. 5.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode. and it worked perfectly. Thank you!

[@jakehedberg4759]

This saved me big time. Programmed two new keys and the seconed one with remote start button was only starting the truck, wouldn’t lock/unlock. Did this procedure and it worked perfectly. Thank you for commenting this!

[@91prostreetstang]

I was going to out smart ford and buy a knock off key..... what a nightmare... long & short I bought strattech key and blammo remote start 79.00 including antenna... forscan is the best

[@Jeffreyrallen39]

In reading some of your replies, you mentioned that, not all the things you need to do with the Forscan can be done from a phone and need a laptop to do them. If using a laptop do you have to use a wired adapter or will a wifi/bluetooth one work? Great video, and seems easy enough to do to a 2016 f350

[@JackofAllMasterofNone]

I would only use a usb wired connection. Bluetooth has a risk of disconnecting and corrupting your vehicle computer.

[@AronCooperman]

Awesome video and links, super helpful in adding this to my 2013 f-250

[@ryanchristensen4291]

Awesome info I did not even know now!!! I have to do this to my 2012 F-350 power stroke

[@bam-bam-boom1726]

I just watched another video and the poster said to change the FORScan code from 0047 to 0148 ... but you said from 0047 to 0147 just curious why the difference and yet BOTH appear to work ( at least in the video )

[@nigelio3]

I only have 1 factory key. If I have a 2nd key made for me and programmed by a locksmith that has the remote start button on it, will that be all I need? Or do I need a 3rd key?

[@TMCityCenturion]

I got an antenna + 2 key kit off of Amazon similar to what you've got in the video. Got the keys cut at a locksmith for $5/key, and got them programmed via FORScan. I only had 1 working key from the dealership, so I programmed both new keys using FORScan. Both keys will now manually lock/unlock the driver's door and crank the engine BUT none of the 4 buttons on either key work (can't remotely lock/unlock doors, can't turn the alarm on/off, and can't remotely start the vehicle). I tried changing out the CR2032 batteries in them, but no luck getting any of the buttons to work after that either. They're working PHYSICAL backup keys...but I really got this kit to have the remote start feature. These were not Ford OEM keys. Does this seem like a problem with the electronics of the key, or did I do something wrong programming them?? Really helpful video as far as the FORScan stuff too.

[@JackofAllMasterofNone]

Non Ford keys must be programmed like a key fob. Look up the instructions for a regular key fob. They don't program automatically with the key like an OEM Ford key does.

[@pbr549]

Great video. I have parts on order. Can you tell us what address spaces mean what? I got the 0 to 1 to make it start, but what display choices do they have. Thanks. Oil life remaining.

[@joeg.1119]

Go to Amazon it's cheaper getting the antenna and the key fobs also..

[@rodf.61]

Got up to the point of programming the new key however it only starts the truck but doesn't lock/unlock doors. Any help what could be wrong and how to fix?

[@lennie76]

Excellent info. Thanks!!!

[@kennyguardado7795]

I have a 2012 Ford F-250 that came with only one key and I got the same kit that you have that comes with one remote start key. How do I program that one key with the only one I have that came with the truck. Thanks

[@JackofAllMasterofNone]

Using Forscan you can go through the add a key service procedure. You will have to go through the timer process to gain security access but it is easy. Just Google "Forscan add a key". There are many posts on the topic.

[@kennyguardado7795]

@@JackofAllMasterofNone ok I’ll definitely look into that and another question for the obd2 USB adapter can it be any one or is it supposed to be a specific one

[@briandowd7842]

Thank you for taking the time in doing this video! I just did the installation and the remote start feature worked great on my 2012 f250 xl. I have the non color basic display. If I change the coding for that, can I adjust the remote start time? Or do I need the fancy display? Thank you

[@JackofAllMasterofNone]

I believe you can change the run times inside of forscan no matter what instrument cluster you have.

[@jew0182]

Jack of All Master of None but the instrument cluster display can’t be changed ?

[@functionxy]

This worked even without power locks? I have an xl without power locks and was wondering if this would work for me.

[@edtooltime1957]

👍NICE Job Thank you for the installation great job on the video good info

[@JackofAllMasterofNone]

Thank you

[@danger1138]

Hi thanks for the awesome video can you please send me a link for the remote start key and how I know which the correct key for my truck ? I have 2012 Ford F-350 Do u think I should buy the kit from the dealership or online?

[@my101209]

It seems pretty easy but I don't have a computer that I could plug up into the system on the truck. My question is will it work for a 2010 Ford Expedition XLT? I've tried to turn the key to get it to recognize I've done both keys but no can do. Could you tell me how I can do that before it gets too cold for me to go outside and trying to start it because I'm in the midwest in Illinois and it will get freezing outside and I don't want to freeze trying to get outside to get to the vehicle to get it started to make sure it starts. I appreciate your help.

[@JackofAllMasterofNone]

The 2010 Expedition has no capability for a OEM remote start built in. You would have to have a traditional one added or if you want an OEM Ford remote start system you can get one but it still has to be installed the hard way, wire by wire.

[@alpaca4463]

Will this work for the XL trim for a 6.2 gasser? No power locks, windows, or anything.

[@JackofAllMasterofNone]

I think you have to have power locks, but don't quote me on that.

[@towtruckdee3959]

So i have 2 original keys & the Lock / Unlock / Remote Start does not work on those. Which is why i purchased a new key & had cut & programmed. But how can i program the FOB to work Doors. Please help. None of these work.

[@0519cubita]

hey man great video can u send me a link to the ford programmer i have a2016 ford f250 xl super duty gas 6.2 thanks

[@skeppley]

When you enable remote start and suggest changing the "1" in 0047, why is the new number 0148?? Did you change the "7" to an 8 also? Thanks so much for this, just got a new to me 2015 F250 and love this video!

[@JackofAllMasterofNone]

No I did not change it to an 8. You only add the 1 in the 2nd position. The program changed it to an 8 after I wrote it to the computer.

[@my101209]

Question: Does the same way to open a 2010 XLT 4×4 Ford Expedition work to start as a 2011 Truck?

[@JackofAllMasterofNone]

No it is not.

[@my101209]

Wow, I just saw your reply. Thank you.

[@delsloat9130]

I have always set head lights on highbeam level and straight.i like the look of the day time runnig lights.

[@confitz6]

I enabled the remote start with forescan in my 2016 f250 xlt. I don’t see the political or the tpm in my truck.

[@drewhaws4256]

is there a limit to how many keys can be added? the first one coded and works fine but the second one seems to take but doesn't work the locks or remote start. Also, your instructions are great! One issue I am having (not sure you can help), after I activate the remote start with FORscan, I cycle the key, step out as you do and test. It works but when I un hook the OBD and try it doesn't work. Any clues???

[@drewhaws4256]

Update, seems there is a safety feature that I must hit the "lock" prior to pushing the start(even if truck is already locked) on the key faub. Still curious is I have a defective second key or if there is a limitation to how many keys can be codded at the same time?

[@JackofAllMasterofNone]

If you have an aftermarket key (not oem Ford) you may have to program the keyfob part of it separately using conventional remote programming. Its usually something like this. You do not have to do this with an oem key. If you bought the key on ebay or amazon,.its probably not a ford key. How to Program a Ford Key Fob Enter your Ford vehicle and close the door. Slide the ignition key attached to the Ford key fob into the ignition. Turn the key on and off eight times (do not start the car), leaving the key in the "On" position after the eighth turn. ... Press one of the key fob buttons within 20 seconds to program the key fob.

[@andreik1775]

2015 explorer has the same TPMS module. It is located in the back of the center console. I used forscan to activate the remote start. All works but the range is not great. Do you think the same antenna can be used? That antenna wire in the kit seems too short to be able to drag it from the bottom of the console. That antenna part number BC3Z19G364A doesn’t mention explorer.

[@JackofAllMasterofNone]

The explorer probably has a different antenna part number due to having a longer wire. I don't know that for a fact though. The reason you have poor range is because there is no antenna so you need to address that in some way. I'm sure the one for the f250 wood plug in and work but like you said the wire would probably not be long enough to go very high

[@andreik1775]

@@JackofAllMasterofNone thank you for the quick reply. I searched for the explorer antenna, couldn’t find anything except this part: JS7Z-15603-A. It is for 2020 and newer Explorer, so I have doubts whether the connector is the same. I decided first to try something else - ordered a cheap antenna suitable for frequency 315mHz. It comes with the RCA wire. I have a f2f coupler and another RCA cable that I cut off and attached the square antenna connector for TPMS module. If it doesn’t help, I will buy the mentioned part. It is $30 or so. I will report back.

[@andreik1775]

The generic antenna with RCA did not seem to increase the range as much as I hoped. I ended up obtaining an OEM DA8Z-15603-A off a 2011 Edge. The part fits these Fords: Ford Edge 2011-2015 Ford F-150 2011-2014 Ford Flex 2013-2017 Ford Super Duty 2011-2016 Interestingly, Explorer is not listed. Anyhow, I used it on mine. I had to extend the wire, removed antenna from the plastic box, wrapped it in soft foam, and tucked it in the headliner. The remote start range seems to improve. But, maybe it’s just wishful thinking. Anyhow, done with that.

[@slapnpop80]

So, apparently FORscan requires you to buy the extended version to enter the as built bodyCM page. Every time I try to enter it, it pops up that message that extended version is required.

[@dubbjohnson]

Where do I buy the antenna that goes behind the glove box?? I have a 2011 diesel w 6.7

[@JackofAllMasterofNone]

eBay.

[@richardowens9609]

Is it normal after all this is done and the truck starts for nothing inside the truck to power up until you turn the key on? Reason I ask is I just did this to my 2012 F-350 XL and it doesn't power up anything inside, including the radio, instrument cluster, or HVAC controls. So I cannot set the heater on or the AC on in the summer to pre-heat or cool the vehicle. Kind of defeats the purpose of the remote start if you can't have the heater or AC working while in remote start mode. Just wondering if your truck does the same thing. Thanks for the video! Was very helpful for enabling the remote start.

[@JackofAllMasterofNone]

Yes it is normal but your AC and heater will work. Try setting the heater on and then remote start the truck. It automatically brings the temp up to 70 degrees I believe and then shuts off. Same in the summer. It should cool it down to 70 degrees if the AC is on. Thats how it works in my 2011 XL. All other accessories will be off.

[@bayseyobi247]

@@JackofAllMasterofNone first I want to say thank you. I did fallow instruction and everything work perfectly except heaters, my truck is f350 6.7lt 2011 XL. I have the non color basic display. They have any code for heater control etc. thank you again for wonderful video

[@JackofAllMasterofNone]

@@bayseyobi247 See my comment above. There is no way to control the heater manually. It is supposed to either cool down or warm up the truck depending on the outdoor temperature, but I usually leave the heat on defrost before I turn it off in the winter.

[@greggschena9716]

Worked like a charm thanks.

[@sgrasmick82]

Is this part number specific to diesel vs gas engines? I have a 2012 diesel. Thanks!

[@JackofAllMasterofNone]

Same thing for gas or diesel

[@adigggert]

So followed this exact for my 2011 xl 250 and upon using the key for the remote start I get nothing. When pushing button for the 3rd consecutive time the horn honks but the vehicle doesn’t start.

[@JackofAllMasterofNone]

Any check engine lights? Or missing hood switch? That horn honk is the truck telling you it can't start because of an error.

[@adigggert]

@@JackofAllMasterofNone after going through it some more found the under hood switch has gone bad. Thank you for the great video and all the help.

[@JackofAllMasterofNone]

Very good.

[@someguy4476]

Great video!!!

[@mobilemushrooms]

Has anyone done this on a 2014 F350? Same procedures as outlined in this video? Thanks!

[@bobert6754]

You said you need factory keyless entry but you don't even have that. Do you mean power locks with remote fob? I bought my kit and realized i don't have door keypad (keyless entry) but... you don't either. Please let me know!

[@JackofAllMasterofNone]

Keyless entry is the remote key fob. The door keypad is irrelevant. So I and you do have factory "remote" keyless entry.

[@abelardobuentello8033]

I have fast blinking on my turn signals I got led bulbs with no resistors I heard dealer could fix by computer don’t want to take to dealer can I fix with forscan?

[@randallmark1403]

Ok here we go. I have added the antenna to the TPMS. I have found line 726 19 01 in the BCM (as built). The line has been changed from 0047 0148. I have also found and made adjustments in my IPC module. I now have the feature for Remote Start ON/OFF in the cluster menu. Problem is I cant get my key to program. I have used the 2 key method in the Owners Manual (On/Off 1st key etc, etc.) I have also tried to program igniton key with Forscan in the PATS menu and it just tells me Key Not Read or Ignition Fault. Any Ideas? And for what its worth Im working on a 2011 F250 4x4 6.2L Super Duty...

[@JackofAllMasterofNone]

Is it an aftermarket or genuine Ford key? A lot of aftermarket cheap keys dont work correctly.

[@randallmark1403]

Problem solved. It was a cheap Chinese key. I have since found two OEM keys and both work great. Now on to my next adventure. I am trying to add Steering Wheel controls with a Steering Wheel that is plugged on the right side. I have the Air Bag off and see that I have to add not just the Audio button group but also the harness. Parts ordered. I am very carefully trying to work the plug out without cutting the steering wheel. Wish me luck.

[@beatkidblaze]

I have a 2014 explorer will this same method work? Where do I get the OBD plug?

[@davidmcclellan4621]

Old video I know, but do I need to upgrade the cluster to have the color screen for this to function?

[@smokingjc5327]

Worked perfectly!!! thanks

[@MrJanarli]

Have a f250 XL, is that duration menu still available on the more basic cluster?

[@singlsrvngfrnd]

No it's not, but you can swap in an 11 or 12 Lariat cluster and have it plus everything else they come with. Program the new cluster with forscan and watch a couple YT vids for tutorials.

[@MrJanarli]

@@singlsrvngfrnd can confirm the duration menu works on the more basic cluster on my 15 xl, I changed the same exact line of code you did and it added it to my setup list

[@Csf0206]

How do you program the key through forscan if you only have one factory key?

[@cecilbrown6905]

Will this work with only 1 key down twice? Only got 1 key from the dealer and i wanted to program the new key with auto start

[@JackofAllMasterofNone]

No that won't work

[@donvickers4464]

The first key you put in the egnition, is it one to be programmed or your original truck key?

[@JackofAllMasterofNone]

Original

[@craigbillay6315]

Since with FORscan you can enable the truck to accept the command to remote start. Is there a way to enable the truck to accept the same remote start command from the key while the truck is running, then remove the key and leave the truck running without it shutting off until whichever user selected timed duration it is set at runs out?

[@JackofAllMasterofNone]

I do not think so

[@dkuhn1807]

My Dealership just told me that they cannot activate remote start if they didnt sell me all the products. Also that the activation will void all old keys and I will only be able to use the remote key from here on out. Would have done it myself but I didnt have the usb connector for the computer/truck interface. gonna buy one now and not go back to that dealer.

[@JackofAllMasterofNone]

Yeah They fed you a line of sh&$

[@alexanderreyes6420]

How about the 2011 to 2015 explorer xlt can it be installed too. I heard it can

[@mikeshortsleeve4356]

I have 2012 F350. Came stock with the remote starter. I just want a new key. If I have a key Cut and program the new key with the two original keys. Will the remote start operate on the new key? Or would I still need the forscan?

[@JackofAllMasterofNone]

It should as long as it's a real Ford key. If its a generic one you will have to program the fob as well which is easy and doesn't require Forscan either.

[@travisgilbert7906]

Wanting to do this to my 16 but i only have one factory key can you still program a new remote key

[@JackofAllMasterofNone]

With forscan yes

[@brandonphillips106]

I have a 2015 XL but I don't have the hood switch. I don't have an issues getting one bit what is it for/do? Also do you know how difficult it would be to install factory fog lights and switch? Thanks and great video. I didn't even know this was an option. I was going to go for an after market remote start.

[@JackofAllMasterofNone]

I dont understand your question about "one bit what is it for/do?" As far as fog lights its as simple as getting a different switch and installing the lights. As long as the wiring is already there, which it most likely is.

[@brandonphillips106]

Jack of All Master of None sorry I was saying I didn't think I had a hood switch and was curious what it's for or what's it do?

[@JackofAllMasterofNone]

The hood switch comes on trucks with a factory alarm system. Its main purpose is to trigger the alarm. The remote start system requires it as a safety feature so that the truck can not be remote started if someone is working under the hood.

[@randallmark1403]

Brandon, you can get Factory Look Alike Fog Lamps on Ebay for about 60.00. The install and look just like factory. But they work independently with a switch and relay. Here is the URL www.ebay.com/itm/2011-2015-Ford-F250-F350-F450-XLT-Super-Duty-Clear-Bumper-Fog-Lights-Switch/121531111690?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

[@CallMeColtLLC]

Brandon, I just made a video on my channel about adding fog lights that may help you.

[@yonisalhov6387]

Can you help me remot start a 2022 king ranch?

[@rogerwhite9940]

When you have Factory Remote Start, What do you do with the key? Put it in the ignition or let it be?

[@JackofAllMasterofNone]

Have to put in ignition otherwise vehicle will turn off as soon as you press the brake pedal.

[@Bam.videos]

As far as changing the cluster menu. Is it the same if it’s the lower end cluster? Is it still a B?

[@JackofAllMasterofNone]

Yes. Same procedure for a base cluster.

[@k-dizz2520]

I run a mini max tuner plugged into the OBD port. Any chance the dealer will screw something up unplugging the tuner and reflashing the BCM? In theory it shouldn't effect the ECM at all, but I'm worried about some of these dealer techs

[@JackofAllMasterofNone]

Do you have an offroad setup? Like egr delete and offroad exhaust? Reason being they will try to automatically update the ecu when they plug in the IDS scantool. It usually prompts them to do it. This will destroy your custom tune and you wont be able to reflash it. I would either not let the Ford dealer do it or would return to a stock tune (not sure if truck will even run on stock tune) and then after they update re download your custom tune, if it even still works. Best bet is to find a small shop to do just what i said or tell your dealer not to touch the ecu programming at all and only update the bcm. Good luck with that though

[@jew0182]

Is your truck an XL or XLT? I just a 16’ 250 XL power windows and locks keyless entry. May add the remote start. But was curious how you have the different display in the center of your instrument cluster. Mine is more basic

[@JackofAllMasterofNone]

My truck is an XL. Search my other videos and you'll find how I did it. It's an upgrade

[@jew0182]

Jack of All Master of None thanks man I assume just computer programming on it? A dealer would never do it for ya I’m guessing

[@JackofAllMasterofNone]

Yeah I doubt a dealer would touch it. But luckily for us there are free programs that we can do it ourselves. Aka Forscan

[@cking22001]

So I have a 2016 f250 and I found that my tpms module is not there but thanks to a previous poster I found it above the headliner on the driver side. But I don't have an entry in bodycm for 126-19-01. I was able to enable the menu and it shows the remote start enabled. Anyone seen this? Is it different for 2016? BTW, thanks Ford for moving that. :)

[@cking22001]

Haha. I have a touch screen laptop and ForScan does not respond to swipes. Had to use scrollbar and sure enough there was lots more entries. I now have remote start!! Sweet.

[@aviyov]

How can i find an explanation regarding the code for ford 6.7 using foscan?

[@joebarragan2253]

Thanks for the video but for some reason, it will not work for me. Keys are programmed, I changed the code. I will check the hood sensor to make sure it works tomorrow. I have a 2012 F250 XL.

[@JackofAllMasterofNone]

You have to have the hood switch.

[@joebarragan2253]

@@JackofAllMasterofNone Yes, thank you I have a hood switch. I figured out the problem, I didn't realize that I had to hit the lock button before hitting the remote button twice. It works perfectly now. Once again thanks for posting the video. Do you know how I can get the Hex Codes for my truck?

[@JackofAllMasterofNone]

@@joebarragan2253 www.motorcraftservice.com/AsBuilt

[@joebarragan2253]

@@JackofAllMasterofNone Thanks.

[@otisrhw]

will this work on a 2012 explorer?

[@Chrisguidry1923]

Did u put that cluster in the truck or did it come with it

[@JackofAllMasterofNone]

It's a Lariat cluster. kzbin.info/www/bejne/oJTCYodvjtWFbqM

[@csned2674]

There are many sellers offering the OBDII interface (Elm327 USB Obd2 Modified for Ford HS Can Ms-can MAZDA Diagnostic Forscan), however, the buyers don't seem to be very positive on the ratings... Can you provide a link where you purchased your interface cable (we know yours works from the video). :) Appreciate it, thanks!

[@JackofAllMasterofNone]

Dont have the link but its from Amazon "bbfly" with the switch.

[@csned2674]

@@JackofAllMasterofNone Thank you!

[@yandysanchez9940]

What if I only have 1 original key? How could I program other keys

[@JackofAllMasterofNone]

Can be done in Forscan most likely, but have to do a key programming procedure.

[@tigerfanmike79]

Hey, , I have a question. I did everything you said and the key works but when I hit the remote start the Horn honks once. 2015 Ford F250

[@JackofAllMasterofNone]

Are you hitting the lock button and then the remote start button?

[@tigerfanmike79]

@@JackofAllMasterofNone yes. Something isn't right.. I am very familiar with the remote start because my two other vehicles have it. When I hit lock, start, start, the truck honks once and the lights flash twice.🤷‍♂️

[@JackofAllMasterofNone]

@@tigerfanmike79 check in your instrument cluster menu that the remote start option is not disabled.

[@tigerfanmike79]

@@JackofAllMasterofNone it is enabled. I even switched back and forth between them to see if that helped.

[@JackofAllMasterofNone]

@@tigerfanmike79 My last advice on the subject. You do have the hood pin correct? And all doors are shut right? Also, if you have tried to remote start the vehicle more than 2 times it will lock out the system and honk the horn. First, go start the truck normally with the key and be sure to press the brake pedal a few times while it's running. Then turn it off and get out, shut the door and then hit the lock button 1 time immediately pressing remote start button twice. See if that helps. If not, there may be a programming issue somewhere in the BCM or ICM

[@donvickers4464]

Thanks

[@joeg.1119]

I have a new 2019 ford escape s an I have the same key fob...

[@craigats]

How did you program the up-graded speedo cluster ? I can't get mine to work without flashing on and off . I do have a ids programmer

[@JackofAllMasterofNone]

Do you have to correct part number for your year? 2011-2016 trucks arent all the same part number. 2011-2012 usually interchange and after that im not sure

[@tailaround]

So I lost my key and found it on the road and as I was gonna get it a vehicle drove over my damn keys and it smashed my only key. The fob itself is crushed and the chip in the fob is a complete lost. The truck will turn on but won’t start. What am I looking at money wise?

[@JackofAllMasterofNone]

I would call around to some local lock smiths. They should be able to get you going for under $100.

[@tailaround]

@@JackofAllMasterofNone thanks. Wish that was the case. Called a guy that cuts keys and he had told me that it would run about $395… he says he has too program the key and cut a new one.

[@JackofAllMasterofNone]

@@tailaround That's insane. Call around more. A dealer could do it for less. Assuming you are talking about a Ford chip key since that's what this video is about?

[@butchthompson745]

I installed the unit and ran into a couple of issues. First, the remote entry and panic alarm does not work on the new keys, and second when I went to my local Ford dealership they told me based on my VIN I needed to add a security system for the remote to work. What do you think regarding both issues? Just noticed an error message "INTKEY could not program".

[@JackofAllMasterofNone]

What year and model do you have? Aftermarket keys won't program like Ford OEM keys.

[@butchthompson381]

@@JackofAllMasterofNone Used OEM keys and after finding a dealership that would trust me in saying I've done everything required they got it programmed. Cost me $200 for the program but am extremely happy with your help.

[@butchthompson381]

The "INTKEY could not program" message was too many keys programmed. Security requirement was false, you were right.

[@JUSTINROLLER]

How is this done without the TPMS module? I have everything mentioned in video except for that.

[@JackofAllMasterofNone]

What year is your truck? You have to have the module. On later trucks it isnt in the same spot

[@JUSTINROLLER]

@@JackofAllMasterofNone It's a 2016 F350 I discovered they moved it.

[@Griff_n364]

Is the code that needs to be changed by Forscan going to be in the same places in a 2014 F150?

[@JackofAllMasterofNone]

I'm not sure. Luckily there is a lot of help for the F150 owners on the internet. Look for 2014 F150 forscan spreadsheet. I'm sure the info is out there for you

[@Griff_n364]

@@JackofAllMasterofNone So I got a new key and antennae, I updated the code in the trucks computer, and I added the key and the key starts the truck but everytime the truck is turned on with the new key the display says "INTKEY COULD NOT PROGRAM"

[@viewtube3310]

So if you don’t have power locks this won’t work at all ?

[@JackofAllMasterofNone]

No

[@kenneth1606]

Do you have to have keyless entry and will it work on the basic level xlt 6.7?

[@JackofAllMasterofNone]

Yes have to have keyless entry. Should work

[@thatguyrick52]

Will this work with a 2013 Mustang GT?

[@floridacracker4279]

How/When do you program the 2nd new key?

[@taylormarty5679]

What if I lost one of my factory keys??

[@scuba366]

How long did it take for Forscan to get back to you with the extended license? What is it another program or how did that work?

[@JackofAllMasterofNone]

Immediately online. Just gives you a code to enter

[@davesweany8650]

Can you set the remote start without the cluster and extended license? I've tried it with Forscan but it stops me with out a license

[@JackofAllMasterofNone]

You need the license. Its free and easy to get on the forscan website