After several months of searching for the droning sound coming from the rear of my wife's Grand Cherokee, I finally found the source: the rear wheel hub. So in this video I show how to replace a bad rear wheel hub.
Пікірлер: 62
@christopherhauser13764 жыл бұрын
Excellent humble approach both a very helpful and calming experience.
@kalabash724 жыл бұрын
The o ring your missing is for assembly purposes in the factory. They use it so the rotor doesn't fall off while going down the assembly line.
@imtired29832 жыл бұрын
I’m over here scared for his wife….. 😂
@mikekruty23835 жыл бұрын
“Time for a bandaid” 😂 thanks for making this video man really helpful
@danielhern30002 жыл бұрын
Great video, shows the job very well. Thank you
@edog65046 ай бұрын
Thank you for this video, I was worried about the axle coming out but this helped and I got it done and only lost a few drops of gear oil
@coskuarsiray5 жыл бұрын
very informative. thanks for sharing.
@mattbudek9692 жыл бұрын
Just a quick note, next time you do one or if someone else does one you should remove the ABS wheel speed sensor first so you don't damage it. It's only 1 10mm bolt.
@michaelperry3553 жыл бұрын
Where did you get those airbags in the springs from?
@1plotthound2 жыл бұрын
im in the midst of a rear brake job with new parking brake shoes.when i pull slack in the e-brake cable to hook it with the brake lever,the cable retracts.weird since it moves freely.what would cause this?
@larsandersson98574 жыл бұрын
Great video! It really helped me to prepare for the job. Btw, does anyone know the torque spec for the bolts? I just tightened as hard as I could (my Haynes manual doesn't say anything about the rear hub, only the front).
@rockinronww19627 ай бұрын
He ask you a guestion? what is the torque on the wheel bearing nuts??
@1crazynordlander5 жыл бұрын
That is a really different design. It makes sense. How many miles was on it before you had to replace it? My 2017 Suburban needed a new front wheel bearing and hub assembly at 25K. GM covered it on warranty. But that is way too soon to have to replace a wheel bearing.
@jsergio19715 жыл бұрын
What happen to the O ring you dos not lube?? Does it hold the diff oil? Does it leak??
@ukiahshorinryu22395 жыл бұрын
Thanks for the video. I was able to separate the backing plate and the hub with out removing the e-brake assembly or the backing plate from the vehicle. Just used a couple of screw drivers to separate the plate from the hub right there at the axle. Took about 25 minutes a side.
@eea999 Жыл бұрын
Is there a seal where the shaft goes through the axle? Or the oil could go straight out? I ask because I changed my hub due to leaking oil from axle and 10k km later is leaking again. Someone told could be the axle seal and not the hub..I wonder if there is a seal there..thanks
@kareemjones730119 күн бұрын
Question, the parking doesn’t seem connected to hun at all. Doesn’t seem as if it needs to be disassembled to change the hub?
@wolfsburggti44763 жыл бұрын
Is this the same for a 2013 grand Cherokee?
@seanmcintyre5148 Жыл бұрын
How long did it last? Detroit axle aren’t very reliable I ordered some for a old car I had lasted a couple months
@kylesyx84329 ай бұрын
Is it easier to replace the hub then just the bearings
@user-vd5jp1hw7n2 жыл бұрын
Hello. I wanted to ask you, do you send goods to Estonia?
@drivewaygarage15612 жыл бұрын
I'm looking at buying a Jeep Grand Cherokee with bad rear bearings so this helps me out
@michaelklick95663 жыл бұрын
thanks for the instructional
@bewiens5 жыл бұрын
Hey did your new hub come with an o-ring? It seems mine didn't and a lot of gear oil has leaked out now. Probably have to replace the e-brake shoes now. Luckily I still had my old hub so I can re-use the o-ring. How did your brake cable separate from the backing plate?
@benmendoza51943 жыл бұрын
Hey did you ever figure out the leaking mine also started to leak
@jeffwyman49685 жыл бұрын
look at the condition of the axle spline. it may need to be replaced also. If the hub is chewed up, you will be doing this again in two months.
@thebeddoctor4273 Жыл бұрын
How can you tell if its front or rear?
@Tstark-xi4vc2 жыл бұрын
Great video! I may try this myself. Is it necessary to remove the e-brake assembly, or did you just want to clean it up?
@sikoor166 Жыл бұрын
not nessesairly
@stefaniveratti5 жыл бұрын
Hi! This was a great video, and we followed it to a T when doing our rear hub assembly replacement on our 2008 Jeep Grand Cherokee. However you did not show how you put back on the parking break lever, and we cannot for the life of us, get it back in. it will not hook on. it's just sitting in there unhooked. Can you describe how you but the e brake lever back on. thank you!
@BrianCoenen133 жыл бұрын
I would also love to know haha
@PPPLOVER-p4t10 ай бұрын
Excelente
@benmendoza51943 жыл бұрын
I did the hub assembly on my Jeep but now i realized it’s leaking differential oil from where the backplate meets the hub assembly. Any idea what it could be I know the bolts are on tight
@donors5553 жыл бұрын
Mine has the same problem. I think, maybe the o-ring is damaged while installation. Ir maybe the wheel hub is bad quality, and oil comes from seal.
@benmendoza51943 жыл бұрын
Hey I realized i didn’t put the o ring on problem fixed now
@VroomvroomNY5 жыл бұрын
FYI use a wire brush on the bolts before removing the nuts it will make a big difference
@mattbrouillard95712 жыл бұрын
and penetrating oil
@SEKERAK_est.19855 жыл бұрын
Hey I’m looking to do this on my 2008 Jeep Grand Cherokee. I have 175k and was wondering if this solved your problem and if they those Detroit axel hub assembly’s are holding up well? Great video!
@theprojecthomestead56235 жыл бұрын
Yes! A year later and it is still working great. I even tow up to (and sometimes exceed) the towing capacity and the wheel bearing is still holding up strong.
@SEKERAK_est.19855 жыл бұрын
@@theprojecthomestead5623 Thanks! Looks like I'll be ordering parts today!
@VroomvroomNY5 жыл бұрын
@@SEKERAK_est.1985 I have 45k miles on mine and still running good.
@shawncarnahan24863 жыл бұрын
After watching you tap the backing plate on i wondered if it would be easier to take the O-ring on the back off and reinstall it after I slipped the backing plate on. Easy Peasy and no hammering.
@Bukiet19865 жыл бұрын
What is this the red into coil spring?
@theprojecthomestead56235 жыл бұрын
Those are "Air Lift" airbags for towing.
@Bukiet19865 жыл бұрын
The Project Homestead Thx 🙂👍
@jozsefstricker39834 жыл бұрын
adjuster star you have to rotate...see hole on back plate 11:50 next time :)
@vassg56 ай бұрын
We want to know socket sizes before we start.
@donors5553 жыл бұрын
Hello, Can someone share experience - my WK have this problem too. I did changed rear wheel hub, because there was oil leak from seal. Now i drived more than 1.5 k kilometers, and oil leak is back now, from the same place. What could go wrong with new spare part?
@benmendoza51943 жыл бұрын
Hey did you figure out the leaking I just replaced mine a few days ago and it’s also leaking
@donors5553 жыл бұрын
@@benmendoza5194 no, i haven't. I think, maybe it is bad wheel hub. I will buy some new, and will install new one. Then will see.
@eea999 Жыл бұрын
Hi. Did you fix it? I have same issue. Changed the hub because o leaking oil than 10k km later is leaking againg. Someone told it could be axle seal not thw hub. Not sure. Thanks
@jonfoley30715 жыл бұрын
Did I miss the abs sensor
@theprojecthomestead56235 жыл бұрын
There is a hole at the top of the backing plate that the sensor slides into. You can see the sensor at 9:10. You don't have to remove it or anything.
@Landoniousiii Жыл бұрын
Great video! Wear gloves every time!
@81selfmade12 жыл бұрын
I know its 3 years late but you installed the brake shoe adjuster upside down also there's no need for a outer seal on the hub bearing
@ckproper5 жыл бұрын
How did you know it was a rear and not a front?
@theprojecthomestead56235 жыл бұрын
I could hear the sound coming from the rear.
@Sea2Skyward5 жыл бұрын
Great video awsome
@GSDead2 жыл бұрын
the o-ring also helps the rotor not fall off when your changing a tire..
@elconejocl2 жыл бұрын
No, the brake caliper keep the rotor in place when you change a tire.
@zacharykarna28103 жыл бұрын
In addition to the first aid kit, take your ring off. Trust me.
@willshafer4137 Жыл бұрын
Covered in gear oil 😂 not supposed to be need a axle seal