2007-2018 CHEVY SILVERADO & SIERRA MOTORFAB 3" LEVELING KIT 3" FRONT & 2" REAR LEVELING MOTORFAB KIT

[@michaelprestigomo7332]

I was crying trying to figure out my angle of the lower shock mounts. Same issue so on to KZbin. I’m going to try your way in the am. Fingers crossed and thanks. Great video.

[@albertocortes155]

The best way to line up the hole is, having the upper strut bolts unbolted and line up the bottom of the strut holes , remove the clips and insert a bolt on each hole, and bottom control arm jack it up as you can see the angle of the bottom strut is getting lined up, try to push down the bolts all the way in the holes, and keep lifting the jack until you see bottom strut is lined up, remove one bolt put clip back on put bolt from bottom until tight, and do the same with the other bolt, it works that how i did mine, it's easy.

[@StellsBellz]

I’d like this kit as well for my 18’ but I feel like possibly you could use diff spacer drops as well.

[@Mistah_J_786]

How are the bushing on the motofab upper o trip arms holding up? people are saying that after 10,000 miles the bushing tend to fail.

[@TurnThemWheels]

I have the Motofab upper control arms with only 9000 miles and the upper bushings already went bad and squeak. No grease fitting also

[@xSKYCLOPZ]

Do you remember what size and thread pattern nylock nuts you put on the lower strut?

[@joshbelcher2996]

Don’t do this JUNK

[@rafaelsanchez-yq8pj]

?

[@predwin87]

I did this same lift on my silverado but i felt with 2” rear block on rear the truck still had a rake on rear,so i did 3” block on rear to level the truck

[@Ttow49]

Is it possible to put left side back on right side instead of rotating strut 180 degrees? my vice is not set up at the moment

[@andrewdensmore286]

Why do ya not recommend dropping the rear axle evenly and installing both blocks then tightening it all up square?

[@KongRey]

I’m glad the algorithm brought me here. You think this lift would work with my 2013 Tahoe ?

[@predwin87]

Wait you say you installed 3” in front and 1” in rear, but on your caption it says 3” front and 2” in rear which is in the back 1” or 2” ?

[@ysfvoltz4686]

in the end the end of the video it shows him replacing the 1 inch with a 2 inch bc it was sagging lmao

[@bassstudiosx9780]

Can I do this same thing without replacing the upper control arm?

[@derekjohnson7574]

only if you dont enjoy having ball joints lol

[@gabrielschultz9987]

How long did it take you to put it in

[@stepdaddy21_10]

I’m going to add this level into my 5’ lift kit . I have the lifted strut

[@Bradofmaccly]

I bought 3” front and rear… is that not going to come out level?

[@EBKABK773]

how was it bro? i did the same like you did

[@gaviin1033]

Hey man i recently purchased this same kit but with larger rear blocks, i also have the 2 inch bottom spacer. Would it be okay to stack the upper 3' spacer with the lower 2'? I do have aftermarkey upper control arms, also purchased a differential drop kit just in case the cv axles are at an angle

[@plutovloggin]

never stack

[@robinadduru5377]

How's the cv axles and tie rods holding up so far? Thanks in advance

[@JJBanuelos]

Not sure don’t own it anymore

[@Donnythelatemodeltech]

Great tutorial 👍🥠

[@TheBlackdoom91]

Niceeeee video my friend

[@JJBanuelos]

👊🏼

[@agustintorres3635]

So 35s M/T will fit?

[@JJBanuelos]

Should with the right offset & backspacing

[@Cmanana1]

Did he farted 😂😂😂😂

[@jasonmccawley]

why didnt he do 35's