John Deere 318 420/430 Differential Series Part I

[@philhicks2167]

Thank you very much for this series. I have a 1990 420.

[@russellpsmies43]

Looking forward to watching the rest of this series. I just finished installing a 420 rear end in my 332 and am wondering how your project will unfold here. Thanks for sharing this!

[@mmrbeef]

Once I get ahead on organizing some parts I recently purchased I will get back to this project.

[@bobnoxious8794]

Thanks for all of your videos, you've already helped me several times. I just bought a really nice 430 garden tractor, but the middle freeze plug behind the injector pump needs replacing. Do you have any advice to remove/reinstall injector pump to access this area? I have another 430, and got the new one for a parts tractor, but it's really in very good condition, and I want to keep her going. Thanks

[@marshaldeadwood7359]

hey I do not know if you could help me out on my John Deere 300 the issue it has when we are in neutral the hydro pump transmission loads up so the engine cannot crank over

[@johnpyle8027]

Pretty stoked to watch this unfold. I bought a 430 last fall and it's stripped down and fixed a handful of things. The sheet metal and fiberglass hood are ready for paint. Since I got it I have been looking for a rear PTO set up and either just missed them or the ones I found were for parts. I found and bought a really nice one a fee weeks ago that was only online for 20 minutes complete with the drive shaft, clutch, gear reduction and the two brackets, bolts and even the wiring harness. Saturday Deere called me and the spring that goes in the drive shaft came in. I will start going back together this weekend. do you have any recommendations on a manual? I have been making my way through. but a comprehensive manual would be nice. A guy once told ne Deere quit making the 430 because they wouldn't break! lol

[@mmrbeef]

Congrats on the 430 and the Rear PTO find. There should be a couple videos this week that will be what you are looking for.

[@corbman9049]

My 430 is sluggish. Mostly in reverse. Before I acquired the lawn tractor it would fly. New fluid and filter is what I am fixin to do.

[@mmrbeef]

Sometimes a filter and fluid change can help if the system is plugged up. You may also want to investigate the linkages. Previously was it in high range and now it is in low range?

[@corbman9049]

Yes is in high range. The hydrostatic lever does not go all the way up or in reverse. Yup probably linkage up in the dash maybe. I will change the transmission fluid and filter as it has 2,300 hrs on it.

[@Formulabruce]

Excellent Video !

[@frwilburn870]

How do I receive your response to my questions?

[@michaelnagy4603]

Is the 400 different?

[@dandavis2110]

The shaft in my pump is bad. M90161. Need help. I'm a veteran money's really tight. Would it be cheaper to find a pump

[@sammyboyde6489]

Do you know where I can get a seal for the front and rear shafts of the transmission pump? Thank You for any help!

[@mmrbeef]

You should be able to order them from Deere. I don’t have the part numbers or the cross listed numbers off the top of my head.

[@sammyboyde6489]

@@mmrbeef No love there, Deere doesnt even list the pump in any of their diags, parts guys are lost. I did find the number for the rear one, cr7443.

[@samuellemaster4360]

Will this fit a 318 John Deere mower

[@timstocker5617]

I have a 430 lawn tractor and I can't get it out of neutral. Any suggestions?

[@mmrbeef]

A lot of times if you rock it back and forth you can shift it. The detent can also be a bear at times. If you can shift with your hand, trace the rod back to the differential and see if you can use a screwdriver next to the frame or a pair of pliers to move the shift forks.

[@CarlJohnson-ry3gc]

DO you know the ohm resistance for pto solenoid on J D 455? I have 8.5 ohm I think this is to much.

[@Hillside-Hotrods]

Or switch a 400 into a 300 as a upgrade?

[@timbronson166]

I have a question so the rear speed lever has a in and an out

[@mmrbeef]

Correct, there is an in, middle, and out. Middle is neutral.

[@2deetwo]

What kind of transaxle assy is in a John Deere F935?

[@mmrbeef]

The F935 have a peerless differential hooked to a Sunstrand 15U pump. It’s basically a reversed set up to a 420/430.

[@byronmill]

@@mmrbeef will the axle shaft from an F9xx transaxle work in a 430/420 transaxle? The parts manual show a different part number but a person in one of the John Deere groups claims they are interchangeable.

[@jamiejankord4697]

Will the rear axle from a 400 series fit in a 318

[@mmrbeef]

The rear axles themselves are slightly longer but the differential will mount right up to a 318. If you do not change the axles the tires will stick out a good bit wider.

[@joellefalhon459]

Hello I am looking for a new deck for my old JD 415, my dealer tells me that it is no longer possible to order a complete new one, do you think that a used 50 C would fit it ? Or have you an other idear ; Jacques from France

[@mmrbeef]

I am not familiar with a 50 C deck. Do you have a model number.

[@joellefalhon459]

@@mmrbeef Thank you for tanking care whit my question mmrbeef i got this serial number 1M054CBEECM03483 , 54C Mower deck . I dont know how to pick up a photo of it for you. Thank you very much for your help.Jacques

[@joellefalhon459]

@@mmrbeef on my old deck 38 hd i think the references are deleted

[@joellefalhon459]

My 415 is 1998 year

[@66Oliver]

I have a good 420 rear axle like this for sale if anybody wants one. Thanks for the video!

[@PieManGood1]

How much?

[@66Oliver]

Matthew Buck $400 with all linkages.

[@johnHill-w4o]

I have a 420 the rear end has play like a car with a worn ring and pinion

[@williamriley2528]

Metric vs SAE Dude...!

[@mmrbeef]

What about it? There are both metric and SAE fasteners on these machines.