JOHN DEERE X300 / FAILED TUFF TORQ TRANSMISSION / USED COMMERCIALLY / REPAIR OR REPLACE? / LOW HOUR

MOTIVE X OIL FILTER WRENCH
amzn.to/40MjD1u
Copper spray a gasket
amzn.to/3Z9lonY
Help support my Channel by checking out my extensive parts store here on amazon
➡️ Check out this page from THEMOWERMEDIC1
www.amazon.com...
TOOLS I USE DAILY
MILWAUKEE 3/8 socket set
➡️ amzn.to/3N3ulda
1/4” socket set
➡️ amzn.to/3MTyQaf
Oil evacuator
➡️ amzn.to/3MQM33P
Lawn mower lift
➡️ amzn.to/38lKhsr
Fuel line clamps
➡️ amzn.to/3E0RI5u
#SMALLENGINE #BriggsAndStratton #Kohler #Kawasaki #Spartan #XMark #ToroHashtagClubCar #GolfCart #FuelLines #SmallEngineRepair #SmallEngineMechanic #SmallEngineRepairVideo #KZbin #Repair #Video #DonnyBoy73 #EricTheCarGuy#Mechanic #MechanicVideo #HowTo

[@danieldominguez7146]

I’m always willing to widen my knowledge with more experienced mechanics. I’d like to watch a tear down thanks Mower Medic

[@bizboomer]

Yes, do the autopsy on the trans.

[@davidfoulk3078]

I had an X-300 for two years and I always blew compressed air in and around the cooling fan cuz it doesn’t take very many grass clippings to clog up and prevent the very important cooling of transmission. Parts counter guy at the local JD Stealership told me that and it seemed to work cuz I never had a transmission failure issue.

[@bobmcdoggish9659]

Just this morning I helped my neighbor pick up his similar John Deere riding mower from the JD dealership, and the problem, which was very difficult (3 trips) for the "professionals" to diagnose, was the pulley on top of the transmission. Before all was said and done, my neighbor spent around $1,000 for the repair. That said, any new riding mower will set you back a minimum of $2,000, so repairing an old mower is a tough call to make when the motor is running strong.

[@THEMOWERMEDIC1]

Yes pulley splines can strip

[@waynestefinashen239]

Jeremy here at EP we have had a few of the residential John Deere riders with transmission failures and have sold them for our customers for $550 since they did not want to spend the money on a repair or transmission replacement. Funny that 725 was written on the dash wondering if those are the hours since a dealer told us these John Deere residential mowers fail at 750 to 785 maximum hours and have seen many that only last 370 hours at the minimum end. If the customer allows i would love to see what exactly failed, it would make a great video follow up.

[@danieldominguez7146]

Hello Jeremy. Just wondering EP stands for El Paso, Tx

[@ericscottstevens]

My L118 Limited just started doing this but it is 20 years old. Only 144 hours, but hilly uneven terrain. Yes mowing a BB field with that tractor........they justly got their moneys worth. Great field whoever is tending to it.

[@Nonamebf1]

Yes, please do a tear down. My John deer tran popped and I opened up to find all kinds of broken parts.. cheaper to buy new trans than buy all components.😢

[@randalljones58]

I would like to see you go through it and rebuild if possible.

[@wadepauly7380]

Love to see a tear down!!!

[@mistersnapon]

YES...lets see a teardown!!!

[@robertshatto2995]

Hell yea rip it apart,I have the x350,,4 years now,,might be something I'll be looking at in a few years

[@joesfamilyfarm]

Yes! Let's see the teardown.

[@vernonviper]

i am curous to know if its low on hydrostatic fluid

[@almarble1]

Mine with a K46 did the same thing after 240hrs. Pretty uneven 1.25 acre terrain with a few short, steep slopes. I was surprised how many people wanted it when I posted on FB Marketplace and who knew about the issue. People try to replace the fluid or change to another transaxle all the time for fun. Not my cup of tea. Sold, and then bought the lowest price model with a K58 and we'll see how that does. So far, so good. Fast as a race car.

[@SPCLPONY]

I've mowed a lot of acreage on our farm for many years. Started out with a new Craftsman LT1000 with a 42" deck and 18.5 B&S. For a $999 machine new from Sears, it lasted for years. I actually still have it in the pole barn as a back up. As years went by, I 'reclaimed' a lot more yard to mow. I started mowing around my pond, one pass inside and outside the fence line of our horse pasture. I soon found I was mowing for 4 to 5 hours a week! Time for a bigger mowing deck. The days of the new $999 special at Sears were long gone by now. I bought a Husqvarna LGT2654 new from a local dealer. It was my first 'hydrostatic' (K46 Tuff Torq) rider. I loved the time it saved me. I have too many banks and hills to warrant a Zero-Turn style mower. Well, after a few years, those banks and hills took their toll on that K46. I followed several video how too's and dropped the complete rear end, changed the fluid out. I had to order and wait for a new cap. Finally got it put back together and it really didn't drive any better. Still slow up any kind of hill. Gets worse as it gets warmed up. I used it once for the first mowing this year, and parked it half way through the job. I got on a 46" MTD/Yardman similar to my LT1000. Good ol' trusty belt driven rear! I think I'm done with these hydrostatic mowers. I've built up a collection of similar MTD riders with 38" 42" and 46" decks. I've got 6 of them that all run, 2 spare B&S engines and a spare 42" deck. My kids are old enough to tandem mow right behind me now!

[@481brighton]

Yes!! Would definitely love to see how you rebuild the trans.

[@maltedbarley1]

Go for it!!!❤

[@georgenovotny4421]

I have a tuff torque 400 in my Spartan, haven’t seen any videos on it yet. Hope it holds up.

[@user-ft6ee5sk9c]

Your video and instructions saved me a lot of time and money--Thanks!

[@TNbubba1]

Take it odd mower, do a evaluation, quote oner repair and replace estimates, and we will enjoy seeing either option they choose.

[@MikeJones-jr5hb]

Yea, tear it down that would be interesting!

[@desireebaehler4243]

Heck yeah!!! It would be very informative to see the innards of the trans.

[@davidmoran4471]

I would like to see the tear down and repair. I do know that Tuff Torq are good folks if you need to talk to them. I did my K66 oil change and was not able to get the same volume of oil back in that I had drained. They said to give it over night as there is a port between the gear and motor sections of the transmission.

[@AndrewDrapper]

I’d love to see a rebuild. We just stripped one to replace the shaft, but have not seen a recondition, or what can go wrong.

[@robertm5967]

Tear it down, replace filter and fluid. Might just work better. Just dis mine. Works like new. Btw there’s a new pleated filter design. Much better than screen.

[@JM-yx1lm]

That's not gonna fix it. It's only a temporary fix. The problem is the center section and the cylinder gets scored up and leaks fluid . New fluid is good fluid but will breakdown pretty quick and the problem will be back

[@robertm5967]

I agree that its only a short term fix. But my magnets were fairly clean and my screen filter was plugged with sludge. So my fingers are crossed that i may get a couple more years out of it. I used the tuff torque fluid as well.

[@marshmower]

​@@robertm5967 maybe it had those floaters growing in it. Like a slime or something nasty.

[@michaelmcguire8028]

How many hours are on it Jeramy?

[@AnonymousGameWarden]

Did you end up making a video of the rebuild?

[@tonyratliff1347]

Yes!

[@jkeefer034]

Yes, please do a tear down & rebuild

[@marshmower]

Why i chose a 6 speed peerless gear drive as my first machine. Also steep hills. Not really safe to be honest. Gotta be careful. But a hydro would already have been acting up.

[@billlovett4256]

I'd love to see it. You'll probably get lots of views.

[@seelye1221]

love to see a tear down.

[@georgestrickland9278]

its a k46 tough torque,just replace,they are only meant for level ground mowing,hills will kill them quickly

[@herschelhill6937]

Yes,Please rebuild transmission.

[@jjjuarez312]

Do a transmission tear down.. I'd like to see if it's the transmission

[@JungleBobRepair]

I would like to see it,but they need to upgrade to a commercial mower!

[@herkyhawk2003]

Yes please do a tear down!

[@HarryEllery]

Yes, I’d like to see that.

[@jimrerko3415]

Yes.... Please. Get your helper. I use a Turf Tiger, that's what they need.

[@somerandomguy3868]

Granted that's a good bit too cut twice a week but I would think it capable enough with proper maintenance

[@wldailey]

Definitely would like to see a rebuild

[@darrellhazelwood5647]

on my x300 it will go foward but wont go in reverse until I reach down and pull up on the forward pedal it will back up

[@mikeburke416]

That's probably because your linkage came loose....Happen to mine!

[@wtbm123]

Hilly here and seems many of them fail here . Tear it down

[@larryhankins3586]

I have a X350, I would really like to see what happened.

[@mimelio]

I would love to see a tear down !!!

[@mchl8]

I had a tuff torque 55 open a few yrs back junk

[@scott6052]

Love to see a teardown.

[@mohmedhosny6094]

I hear transmission pump sound i think issue is low oil level

[@aao8181]

Yea I’d like to see that video👍

[@timothylanders3189]

Crikey! Your pretty rough on the forward reverse action :o

[@rayburnett3066]

I would

[@Spencer1609751]

Yes Teardown!

[@barryray786]

It's the forks in the transmission are wore out. I fixed one about 25 years ago. I can draw a picture and show you what it looks like. It was only a $20.00 fix. Don't change the transmission.

[@johnayers8990]

Yes , do it

[@bryanhines34]

Want to see the teardown

[@watermanone7567]

Yes, tear it down, many thanks.

[@davidpawson7393]

One of my Cub Cadets has the opposite problem where once you push the go pedal it doesn't release. Pulley stack?

[@THEMOWERMEDIC1]

I don’t think your cub cadet is hydraulic drive is it?

[@jessramirez6696]

Yes

[@hickorystx]

Yes, disassemblw/

[@chrispeters4405]

need to change the fluid.

[@darrellhazelwood5647]

yes please

[@henrytacam4119]

Yes please

[@johnobiro5202]

Yeah. Do a tear down Jeremy.🔧👍🇬🇧

[@carlosg1165]

Do a rebuild ❤❤❤❤❤❤❤❤

[@kevinhaley6776]

One of my facilities thats fancy talk

[@THEMOWERMEDIC1]

Just stating facts

[@malfaro4]

Do it !! Let’s see

[@jjjuarez312]

Change the v drive belt and the upper belt and the main crankshaft pully I am 100 sure that's your problem..

[@THEMOWERMEDIC1]

I’m 100% sure it is not👍

[@williambrice2265]

Yes tear it down

[@BADD400]

Yes teardown

[@Efffshams]

Maybe cause sham sham Bigelow is too much for its weight capacity

[@beachbums2008]

Rebuild it! Let it live again with the heart transplant.

[@cdnsc]

Help Yeah 👍👍

[@brandonstclair6530]

People pay so much money for these x300 series tractors only for them to end up like this one, busted hood and broken transmissions. In this case you don’t get what you pay for.

[@hydrospeedex]

Rip it open doctor

[@berkeleycountysmallenginer3842]

Tell the customer that mower isn't made for cutting grass at ball diamonds. Tell him what mower to buy for ball diamonds.

[@burgerbirger2221]

Tear it down👍

[@jimrerko3415]

Where's the kid ? 😔 He's the star.

[@jonathanfierberg3807]

No don’t tear it down

[@philliphall5198]

New one

[@YamacrawJess]

Yes, we need to see the guts.

[@tombaker3289]

dirty oil filter.

[@andybecker2693]

It’s just worn slap a$$ out. They got their money’s worth. Looks like they need a 930 for that.

[@kanebenoit8987]

Yes please do a tear down!

[@rickchrist1949]

I would love to see it

[@gregfisher216]

yes!

[@mikeadler434]

Yes

[@dclawnmaintenanceandsnowre4099]

Yes

[@09hoseclamp]

How many hours on it? And is this typical before tranny starts letting go?

[@antoniomarc7174]

Yes would like to see what happened.

[@Jerrylance-ty1re]

Tear it down

[@motoman5023]

Tear it down!!

[@budhoward2528]

Yes

[@rockyholt4060]

Yes

[@newsnowriversidesgtrock]

Do the repair. We need to see the fix for this. I have an LA150 54" and it has exactly the same problem. It starts working fine and within 100 yards it stops dead. If I get off of the Machine and push the go pedal by hand the machine will still pull itself along with my pushing but will not pull with a rider. Fix it, good but, on the cheap parts and fluids.

[@jessramirez6696]

More medic what are you doing okay we haven't seen you lately on KZbin channel hope you're doing okay and God's love and blessings upon you videos okay

[@johnshoe5132]

Yes go ahead and tear it down. But tell the guys mowing the field they need a commercial mower, it will last longer and mow better

[@chrisgarland2272]

Just pulled one out and apart and springs failed in pump. Customer decided to scrap it.

[@astairs36]

You know we want to see you disect it... Lol

[@michaelmorse4357]

Yes. Please do the tear down video.

[@crazyhorseracing6130]

Yes I'd love to see a rebuild!! Thanks

[@jameslainio3752]

Autopsy might be needed.