Jon Cutter 5800-372xp Carb Swap & Info!!!! Watch To The End!!!!

[@BuckYaSaws]

Great how to man! Thanks!

[@Tito_5859]

una pregunta amigo, gusto en saludarte, tengo una maquina igual pero tengo un problema no logro tenerla bien carburada a veces al cortar se ahoga, otras veces no enciende y aveces esta acelerada, el error fue mio que movi por error las agujas y aunque le ponga lo que indica el manual no consigo que este estable...

[@dubbssawshop]

@@Tito_5859 what machine is it? I would start by seating the L & H jet easily all the way in. Next turn them out 1 to 1-1/4 turns out. Get the machine warm, then hold the throttle open and turn the H jet in slowly until it revs a high rpm. Then back it out until it burbles a bit. Go to the L jet, turn it in or out until you find the highest idle speed without trying to cut off, then turn it it out until the rpm just starts to drop slowly and Stop. That should be very close on the jets. 👍🏻 hope this helps, and the translate works well for you.

[@Tito_5859]

Thanks friend, well I'm telling you it's identical to the one in your video, a Jon Cutter 5800 and well I'm going to try what you mentioned before, I hope it works for me because sometimes it doesn't gain power and it turned off, and other times it's working fine then it turns off and it's hard to turn it back on and so on but thanks I'll try.

[@johnarnettsways.8758]

Dubbs. Hello my friend. Just subscribed. Appreciate you my friend. Have a great day sr

[@dubbssawshop]

Mr John!!!!!! Glad to see you here bud. Appreciate it and hope you have a great day as well fine sir.

[@Brush_Cutter_Man]

Very nice to see...

[@dubbssawshop]

Thank you for checking out the video!!! 👍🏻

[@Brush_Cutter_Man]

@@dubbssawshop 👍

[@brennancass3747]

Have you checked the squish? The one zenoah clone I had awhile back had an enormous squish, like .060+.

[@dubbssawshop]

Yes, 😬. It’s setting at an astonishing .044” w/o a base gasket. Definitely has way more room for improvement. Can’t wait til my shop finally has power and I can use my lathe 👍

[@dubbssawshop]

Next I gotta figure out how to squeeze a stack in there. I really like the way Brisco done the echo stacks.

[@brennancass3747]

@@dubbssawshop yikes 😬 yep, power in the shop is essential. If you run out of patience, send it down and I'll buzz it off for you lol. A 2 series stack adapter would probably work. I have a standard 268/272 elbow and stack adapters on my poulan 475 I had up there Saturday. It looks like it would fit about anything.

[@dubbssawshop]

@@brennancass3747 thanks bud I appreciate the offer. Depending on how long I may take you up on that. I have a few red beard stacks but they are a bit to fat to squeeze in there.

[@brennancass3747]

@@dubbssawshop sounds good bud. Shoot me a message and I'll send you pics of my poulan setup.

[@brandanevans5626]

I have the same saw just like yours, but mine came with some problems far as a couple of dents, but that's besides the point I had sent my saw off to get fixed and nothing really was done to it carburetor had a crack to where gas was leaking out of it so I went ahead and bought a new carburetor which was the 372xp just like yours but I have 2 questions My first one is, would it hurt the motor if I ran a 22-inch bar on it, or would it be fine? My second question is if I left the parts that were in as far as the rubber boot and the cover that's on it or what would I need to do?

[@dubbssawshop]

It'll probably pull a 22" bar but I wouldn't max it out, it probably won't pull tongood in 20-22" wood, if your talking about the carb and intake boot, their is an adapter on ebay for these that let's you use the stock boot and stuff to adapt to the 372 carb. It's a black and white color 3D printed adapter.

[@dubbssawshop]

www.ebay.com/itm/255939725095?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=EILSHjj6RGS&sssrc=4429486&ssuid=gCgMQEEWTwC&var=&widget_ver=artemis&media=COPY

[@ScrewdriverTUNING]

Great work brother. DUBBS custom shop now. ❤️‍🔥❤️‍🔥🧬🦾. I love customizing stuff. Stay safe

[@dubbssawshop]

We slowly growing!!!!😁👍