Jumper T16 Setup and Transfer Models From FrSky Taranis X9D

[@ernie5229]

Hi Joshua. I recently bought a Jumper T16. I see amazing potential. However, though I've been flying for 20 years I have NO experience with OpenTX or FrSky. Virtually all instruction for the T16 assumes you know OpenTX and/or FrSky. I'm a Spektrum guy. I would to do the legwork to help you create a video series for the Jumper T16 for the complete noob. I don't edit video, but I'd learn just about anything to learn this radio and help others to learn as well. Please respond if you are interested. Like I said, I'd do all the leg work I can. I am disabled and this type of hobby is so helpful to my life!

[@dbourdea]

i'm using the latest version of OpenTX companion (2.3.1) and trying to copy and paste my models from the Taranis X9D but running into a problem when I hit Read/Write and write to the Jumper T16. I've followed your video and created a new profile and before the copy paste read the models and settings from the radio. Nothing seems to happen when i Write the models and settings back to the radio. When I disconnect the USB I get an error stating "Storage Warning - Bad radio data - Press any key". Then it dispalys a message that it is going into a storage preparation mode. Finally it displays the calibration screen and has me calibrate. Help

[@dbourdea]

I downgraded OpenTX Companion to 2.3.0- after seeing that my radio's firmware version was 2.3.0. I went through the same process as above and got the same error message as above.

[@cappy0815kanal]

Hi Josh, great video, thanks for that. Do you know which model to choose for Jumper T18pro (which comes in soon hopefully) like at 8:00 ?

[@XZLR8N]

I'll wait for the pro, plus or V2 when the Hall effect gimbals are standard.

[@Bionic24]

I think the Hall gimbals main advantage is that they don't wear out after long term extensive usage. The M7 and M9 gimbals however will wear out from dirt due to their open design long before that unfortunately. The standard gimbals on the T16 feel great and the values in the channel monitor are rock solid.

[@scharlatanski5039]

Surprise ! Jumper T16 HALL is on the official Jumper Homepage since 18.07.2019. Would love to see a comparison soon ;)

[@Burn377]

Guess you no longer have to wait..

[@awwtergirl7040]

There are issues with ribbon cables on the T-16 Pro. I'm having all kinds of issues that require re-seating the stupid cables. I'm not a happy camper with the T-16 Pro right now.

[@Dad_K]

@@awwtergirl7040 I had the same issue literally out of the box. I had to open it up & unplug the ribbon cable and wipe it with alcohol for the scroll wheel to work. Overall, the radio is very nice though, & that is my only complaint. I love how easy and intuitive it is to set everything up, as I am a complete beginner. Though I agree, you should not have to mess with a product out of the box.

[@ravendarkcloud]

Thank you for the video. My t16 is tracked to arrive tomorrow and is the first new radio I have bought since I got my x9303 2.4 back when it first came out.

[@BrianKai]

FYI it's a good idea to open the radio up and check the gimbal connections, specifically the jumper wires on the left gimbal. I ordered from ARRIS and during manufacturing this jumper wire was crimped which causes (on mine at least) the yaw axis to fluctuate wildly at full right yaw. Wildly enough that it sometimes applies about 20% left yaw when the stick is at 100% right yaw. They're taking care of it by shipping me a new one. But check the monitor thoroughly before flying just in case.

[@rcoops58]

At 12:06 in the video you get a "Telemetry" option, I don't! I am running Jumper TX-t16 ver 2.2.3 from 2019-05-23. Any idea why? Thanks for the thorough videos. I will learn OpenTx if it's the last thing I do!!

[@michelzevenboom486]

Hi, do you still have the problem?..i am running in to it now and dont know how to solve...thanks Michel

[@rcoops58]

@@michelzevenboom486 I do still have that issue. I kind of gave up because I got no response. If I find anything, I will try to post it here.

[@michelzevenboom486]

@@rcoops58 Hi, now i got it to work...you have to go to the model menu and go to the last page telemetrie..then " discover new sensors "...i had my quad copter bind while i did that..exept mine is not support batt volt..maybe depents type of reciever.. Hope it wil work for you. Gr Michel zevenboom

[@jpsalis]

Don't you need to rebind your transmitter to your receiver each time you go to fly if you set it up this way?

[@vovsen123]

just followed your instructions, but it just go into emergency mode as soon as it had checked buttons and throttle. tried new firmware even if it was the same version and now i end at the startpage until I tried to do anything with the moddel.

[@d.b.cooper]

Villy Feltmann I am experiencing almost exactly the same thing. Not sure why, probably a version issue. Perhaps I need an older version of open TX companion. Anyway I resorted to manually entering in all of the old models. It’s only 32 so it’s not that bad.

[@bobflyer4346]

This is due to the Companion program having the model (s) set for the internal Multi module. For each model, you need to turn off the option for the internal multi module. This is with the Horus x10/s as the device selected in companion.

[@bobflyer4346]

See this URL kzbin.info/www/bejne/m4eaeXytacl4oNU&mc_cid=bd08e4df82&mc_eid=c903cfbf09

[@vovsen123]

BobFlyer Thanks Bob I appreciate your advice, it solved the issue.

[@guneyhtr]

Hi Joshua, I am new in this hobby and learning a lot from you. Thank you for all your help. I bought geprc cinequeen 4k and bind it with jumper t16. After wrote models to jumper with companion 2.3 I got an "storage warning bad radio data" on my tx screen and everything was gone (like factory reset). Maybe jumper tx is not compatible with companion 2.3. Do you know any compatible version because I'm tired of doing everything again without the companion?

[@JoshuaBardwell]

Yep exactly. But good news is the new OpenTX is coming in just a few days or maybe weeks with full Jumper T16 support.

[@ashik.r.m]

Hi Joshua, Just got radiomaster T16s as very new to opentx, I am having issue with throttle and pitch curve for Heli. Can you assist please? Thanks

[@RIFFRAFF29]

Hi Joshua. great video i recently received my Jumper t16 pro and tried to transfer models from my Taranis x9d+ to the new radio but i get an invalid data error and the radio reboots to original settings, and i have to do a calibration and i loose all my models 😟. any thoughts on what i might be doing wrong?

[@paulrobinson4888]

I'm having the same issue. Don't wanna have to reprogram my models.

[@thomasvelsvik7423]

good and detailed video! Are you planning on making a video on how to update the software as well? On my taranis I have only tried it through the companion. Is it possible on this controller?

[@Tintin-ko4vi]

Hi Joshua thank you for the video. I am having trouble binding my Frsky receiver, I didn’t notice you had to press a button on the receiver before you plug in the battery on the quad. Is this step not necessary? Anyway I have tried D8, D16, D16(8 channel) still not binding. I am still trying to figure it out. Hmmm

[@Nelsonv2]

Alert !!! I just got the Jumper T16 Pro. To work with dsm2 and dsmx receivers BOTH internal RF and externa RFl have to be ON in the model setup menu. After hours trying to make it work with the internal RF only and no response I try both on and wala!! works.

[@mmmasterscross7915]

Joshua Can I transfer models from a Spektrum DX8 Gen 2 to the JumperT16 Pro? Thanks in advance

[@yosemite7733]

I've just got my first open source radio Jumper T16 and I downloaded companion. In settings it ask for build options. I mainly plan to fly quads and maybe fixed wing.

[@Billbobaker]

Got mine yesterday and just love it.. It feels weird ergonomically however compared to my Taranis XD9.. Love the big color screen and moving all my models was easy thanks to this video.

[@Rcmodelgeeks]

Thanks for the video Joshua. Completely agree with your views on the T16. Its early days in the life of the T16 and there are bound to be a few little issues, which i'm sure will get sorted. I was only thinking today can i transfer my models over from the X9D to my T16 and you answered my thoughts perfectly.

[@Ulrik47]

Has the ch1-ch8 problem been solved?

[@bengmo64]

I just got mine, and the roller no longer requires two clicks after updating firmware. And they added D16 8 channel mode.

[@fizounet1]

Hi. I tired to set up the widgets in the top bar as per your video, but I cannot find telemetry in the source list, the list just go to Gvars, there is no telemetry after that. where did it go?

[@JoshuaBardwell]

You have to go to the Telemetry screen with your quad plugged in and "discover sensors".

[@bdmvy]

Found this video very useful in copying my models over from my Tarannis to my new T-16. I copied the models this morning, rebooted the T-16 and it sizzled and smelled of burn chips. I opened it up, couldn't find anything obvious, gave the case a firm rap and then discovered a free gift from Jumper, an extra screw, the type used on the gimbals. It had clearly been dropped by the assembler and too lazy/busy to fish it out, left it where it went on to short and fry the radio.

[@JoshuaBardwell]

Definitely take this up with whomever sold you the radio.

[@bdmvy]

@@JoshuaBardwell Already wrote to Jumper XYZ and my vendor, who have been very responsive up to now. They are in regular communications with Jumper and speak the same language! I really like the radio and worth putting up with the teething problems of a new product line.

[@serpentine4684]

I tried making models on OpenTX but it won’t work, I have to do it right on the t16. Help!

[@h2o-fpv623]

Hey Joshua I'm having a little problem I think I have everything set up in the drone ok but in the radio I'm no able to move the motor please can u help me to see If i can start with the motors thank u

[@tiger8157]

I've been using spectrum forever. I have bought jumper T16 pro. Any way I can get a file with a quad already setup. To import on to the jumper. Just need a reference to start from. As I can't get my Shurekin 250 to Arm.. Thanks. Love the videos..

[@ericwil76]

Joshua mine has a noisy speaker white noise very low when on, does yours do the same? You may have to put your ear to the speaker

[@blackmennewstyle]

You can actually display the VBAT or A4 value from telemetry on your main screen with the X9D+, you have to select it on the Telemetry page of your model. I'm pretty sure you can also display another telemetry value like altitude if i recall correctly. I also honestly don't use the Betaflight LUA script that much nowadays with all the cool options being available in the OSD, it's kinda just a rescue option if i'm in a hurry. Have a great week Joshua and keep on flying :)

[@JoshuaBardwell]

You can display one or the other, but not both, on the X9D

[@fredlef100]

Hi Joshua - got my T16 yesterday and followed your instructions to copy and write models from my Taranis X9D. Resulted in Emergency Mode warning. Sounds like the corrective action is to delete all files from SD Card and replace with a fresh set. There appear to be two versions - 2.3 and 2.2. Do you know which I should use? I had the August firmware loaded. Thanks

[@fredlef100]

Found the version is 2.3 and I see some additional info - looks like it won't be too hard to sort out.

[@wehttamak]

i am having issues with the RS for some reason when i slide the slider it isnt going all the way up however on display it is only going half way up the others are working fine for collaboration any help would be greatly appreciated not sure if i will have to open the radio and check on the RS ribbon

[@gmascagni]

Josh it's been a while now that you have had your J T16 just curious if you have made the jump or if there was soemething holding you back?

[@JoshuaBardwell]

Yep I made the jump. Search my channel for "t16 daily driver"

[@JimB40]

Well I saw in one video that OpentTX Companion doesn’t support T16. Nice surprise it works with X10 option. Joshua on my iRangeX multi protocol module there is FrSky protocol called ‘D16 8CH’. When you choose it you can select range of 8ch scope. Can you check if it’s available on T16 module and if ‘LBT(EU)’ and ‘LBT 8ch’ are included? Thx.

[@JoshuaBardwell]

Yes, it's available

[@neilgillies6943]

I have an EU version (or rather, I bought it in the UK, that may be at odds :-). Mine has all the protocols you mentioned.

[@sapata1871]

JB , Got the green lite on the Rxsr but no Go. Doesn't connect receiver in BF? seen a video on tuning frequency but(t12) ?? I have the t16 Any ideas?

[@JoshuaBardwell]

The issue is not related to the T16 once you have bind. Your wiring or FC config is incrrect. Make sure you have the green SBUS OUT wire going to the SBUS pad on your F4 FC, or any UART RX pad on your F7 FC.

[@sapata1871]

@@JoshuaBardwell Thx for getting back to me. I'll troubleshoot . Held down rxsr 3/4 sec. Ta-da .Blue' lite Magico!

[@davidGrainger]

Followed your instructions. All worked, but now when I turn on the transmitter it says, "Storage warning bad radio data" Then goes to stick calibration. Then after stick calibration it has no models. What's up? How to fix? T-16 Firmware version 2.3.0.

[@dannyreimer1673]

Having the same problem here. Did you find a solution?

[@rabidbydesign]

Same see my comment above. I'm thinking when OpenTx 2.3.1 officially supports it companion support will be easy peasy for us X9D switchers

[@buddyadkins2432]

Great video. How do you access the SD card's MODELS? I have not been able to do anything with the Models on the SD card.

[@JoshuaBardwell]

You use opentx companion on the PC.

[@rawfpv3197]

Just got my T16 today went to setup screen and in widgets no telemetry shows up? Anybody ran into this and have an answer?

[@JoshuaBardwell]

Telemetry comes from the receiver and the FC. If you are not using a telemetry capable receiver you won't see telemetry in the t16.

[@Fr3dGarvin]

I’d be interested if it had an internal multi protocol transmitter like the earlier jumper. Not planning to have jr module swaps be a regular thing for me therefore not planning to buy this.

[@Maceyee1]

Why would we change the frsky mode from 1-8 on the transmitter surely it's the receiver that needs to switch mode?

[@JoshuaBardwell]

The transmitter is in charge of how many channels are sent.

[@Maceyee1]

@@JoshuaBardwell thank you.. i learned something today

[@redogg2749]

Hey, How would we update our Xm+ firmware if moving to Jumper. Does "serialpassthrough" work on them all now?

[@JoshuaBardwell]

You can use the JR module plug in the back of the radio but you need to re order the pins in the servo plug that you use to plug in the receiver. Use "flash external module".

[@redogg2749]

@@JoshuaBardwell That's great just like the taranis then, Just ordered my T16 pro cant wait for multiprotocol. Great vid as always! 😁👌

[@ir8dudefpv]

Great video as always! Very informative on a transmitter we don’t see many quality setup guides for.

[@scizzorhandsfpv9547]

Calibrated my jumpert16 a few times but still getting a 1156-1843 range in my stick ends . I need to get my inputs to the usual 1,000-2,000. Any way to change in the radio assauning calibration is correct ? Thank you

[@JoshuaBardwell]

Adjust endpoints in the OUTPUTS screen.

[@scizzorhandsfpv9547]

Thank you, my outputs stop at 100 and -100 . I would need my outputs to go beyond 100 to have the correct value in betaflight . Calibrated the radio again as well.

[@PropsOff]

Question? My friend and I are interested in getting the T16 Plus.. I don't see any new info from you on this transmitter.. Are you using it? Also, if you are recommending it, will you put a link for purchase of the "Plus" version?

[@DanRogers1985]

I followed these instructions to the T and when I select a model it goes into emergency mode. I also don’t have a failsafe setting. Do you know why that might be? I did update the firmware so it should work with my crossfire module.

[@JoshuaBardwell]

One of your existing models has some setting that is not compatible with the new radio. Transfer the models one by one to see which one is kicking you into emergency mode.

[@kbdfpv3341]

It seems like all of them do it, so now I am setting each one up from scratch. I was also an idiot and forgot that D8 doesn't have a failsafe setting, so that part can be ignored.

[@vovsen123]

you need to turn of RF module in Open TX companion and then add it manually in the radio

[@Billbobaker]

I ordered one of these today.. You convinced me with the speed/ease of programming.. I currently have the Taranis XD 9 plus with their multi protocol module.. Hope they can update it to use D8 mode soon.,

[@JoshuaBardwell]

It does support D8 already doesn't it?

[@Billbobaker]

@@JoshuaBardwellYou didn't seem able to change the channel range to D8 at 13:40.

[@jandomingo9806]

I did everything right but when i yaw its going crazy on the throttle. I changed it to aetr and just plugged in my crossfire from my qx7. Made it mode 2 and aetr. Idh to fix it. Might sell it

[@matthewbarger4592]

im new to all this however Ive got a lot of experience flying gliders. what id like to know is can i use my old model dx 6i to fly quads or should i just get a new radio?

[@davidkernica9676]

A dx 6i will work espically for a brushed whoop, but you will need more channels, eventually. As a spektrum user and fan, I own both a Dx8 gen 2 and a Dx9.For quads or even a mix of different rc models, I think this $150 multiprotocal radio can't be beat, I'm even considering selling my dx8 and buying one

[@oakfpv9982]

Joshua Bardwell Do you know if jumper tx will release some hall gimbals?

[@Nubyrc]

Mine will not bind with any Fr Sky receivers I have!

[@ursmerz]

Hi! Small question, do u know if the Jumper works with FrSky L9M and if yes with which setting?

[@AdrianoCasemiro]

Will it run the frsky R9 module?

[@JoshuaBardwell]

Yes.

[@RaptorXTUK]

Yes and look up the Flexi firmware just for the R9, it adjusts the R9 power output on the fly up to 1watt.

[@BigWillieFPV]

How do I get the endpoint set? On receiver tab in BF I can only go as low as 1020 thanks

[@JoshuaBardwell]

Enable "extended limits" option in the Model Setup tab.

[@BigWillieFPV]

Thanks That worked I’m 1000/2000 now but I’ve lost resolution with the sticks

[@BigWillieFPV]

All good sorted thanks again JB 😃

[@testpiloterb1828]

Hey I know this is off topic but I just picked up your flight controller and 4 in 1 do I need a BEC? I’m still noob but I’m learning and building my own rooster

[@JoshuaBardwell]

You don't need a separate BEC. The flight controller has voltage regulators on board.

[@testpiloterb1828]

Joshua Bardwell awesome thanks so much I’ll be joining u on patron soon literally every time I need help with something you have a video on here with my issue.. I actually just watched your video on your quad with black camera feed and mine is the exact same as urs my camera works but unlike u mine hasn’t started working again yet.. so yeah :-/ anyway thanks for all you do for this RC community!

[@adriancjones]

Hey Joshua, if I’m using the old 2.1.9 firmware can I copy the files to the t16 or do I need to update firmware on the Taranis first before proceeding?

[@alexandereckhardt7153]

Do you like the jumper t16 better than the nirvana? Why or why not?

[@stevenshook5676]

Hey Joshua, just bought a Jumper T16 Pro (the one with the Hall effect gimbals). It's been a bit of steep learning curve but I finally got up the courage to bind my TinyHawk (RTF model) to the Jumper radio yesterday and finally figured out the switches. Flighs great too. Just wanted to say thanks for the videos on the radio! Are you using the radio for on a regular basis? Thanks again!

[@tinorosenkranz7822]

Thanks for this video my Jumper-t16-pro will be delivered tomorrow 👍

[@ismaelmercado9861]

isn't it basically a Futaba?

[@DrDiff952]

But when do we start seeing hydrodipped cases for the T16?

[@JoshuaBardwell]

Nobody really seems to be doing hydrodip for rc parts any more. Not professionally. Vinyl skins are more popular.

[@RADERFPV]

Side question JB - Are you planning on reviewing the Armattan Marmotte frame or BNF anytime soon? Curious of what you think of it compared to the Chameleon and Rooster. If anyone else has experience with them, can you please chime in? I'm very interested in it, but have been hearing of some pilots breaking the frame quite easily. I get it's under warranty, but what a pain if that's the case. Thanks Joshua, thanks guys.

[@JoshuaBardwell]

I'm actually editing that review right now :-)

[@RADERFPV]

@@JoshuaBardwell- So awesome, and thanks for the fast reply. Really looking forward to it :D

[@tykinsey4338]

Good day Just bought a t16 and it's lagging with the input. I'll press a button and nothing happens. Any ideas?

[@danlineberger]

I am torn between this transmitter and the Taranis X9D SE. Newbie to quads and would like to spend a little more for quality.

[@derrickmitchell39dm]

Hard to beat that Taranis. Its affordable, fully programmable, it's been around like forever and it functionality is easy to understand.

[@derrickmitchell39dm]

@@JDDupuy 🤣😂🤣🤪

[@derrickmitchell39dm]

If y'all think I'm not going to get me a Jumper T16 pro your crazy 🤣. My loyal girl from the block is cool but I gotta get them hips and lips. Besides, the Jumper T16 pro is a better Tx and reasonably priced. I'm all in!

[@yuginoty65]

Thanks for your videos. I've like my early QX7. It has been a very good tx for two years. I have run into the need/want for more switches though. My son's Spektrum DXe has become very limited for his Kwad flying recently. That has me considering tx options. Before the release of the Jumper T16, I was pondering the X10S. The X10S is almost four times the cost of my original QX7. Now I'm considering the T16 with my son inheriting my QX7. Switching companies again. I thought it would be nice for my son and I to have the same company products so as to be able to use rx'es, tx modules, etc. I would appreciate your advice on this. Thanks again! Peace...Guy

[@JoshuaBardwell]

I think for the price of the T16, it will be a good value even if there is a bit of risk compared to a more established product.

[@yuginoty65]

Thanks Joshua.

[@vovsen123]

why does the lua script for S6R and S8R work? And be aware that transfer models from taranis need careful checking as they (normally) refer to internal Sender and not the 4in1 external.

[@JB-cq2wo]

is it hard to set up a full size crossfire module to work with this bad boy ? I need cross fire. 99% RSSI forever. lol

[@mikethomas7763]

Joshua please do a video on bind and setup with flysky. ....please

[@richfpv472]

New jumper T16 pro v2 out now and it's not badly priced, has hall gimbals supports crossfire, USB-C charging what's not to like more switches than you will ever need, especially for multi rotar pilot's (Quad copters)

[@bigrob21mx]

i have followed this on the new version and the models are not copying over.

[@davidkernica9676]

What I really want to see is how you feel about it after 3 to 6 months.

[@maxun1]

Does this radio support R9 module?

[@discord2000]

Anyone else notice there's a target in the JumperTX Hithub repo for a "T16HD"? :o

[@2windboy]

Hi Joshua. I purchased T16 and try to transfer model from X9D+ to T16 using OpenTX companion 2.3.1. After write model to T16, When I turn on T16, it display Bad storage Error. T16 is initialized Calibration screen. I am using Windows10, OpenTX comapanion 2.3.1, T16 plus with 2.3.0 firmware. How to Fix it? Thank you.

[@JoshuaBardwell]

Delete models from T16 and see if the error goes away? Check SD card to see if it is damaged or not inserted.

[@dannyreimer1673]

Did you find a solution? I am having the same problem

[@rabidbydesign]

Yea same thing happened here - it didn't like the model transfer on T16 2.3 fw. When it detects a problem it resets to like when you have a fresh SD card loaded with default content. I'm guessing this video was made with 2.2.3 fw - based on date.

[@dannyreimer1673]

The solution is downgrading the opentx companion. The newest versions seems to have problems with the Jumper T16. After downgrading everything worked fine for me.

[@2windboy]

@@dannyreimer1673 Thank you for your advice. Which version do you use? 2.2.3?

[@aftabbangash4484]

Plese sir tel me about servo reverse setting in jumper t16

[@rolandburrows4859]

Sir, is it possible to get a copy of your model setups? A file?

[@JoshuaBardwell]

1drv.ms/f/s!Al4b3QGPtgasnbUUuLeJhQtPg0EO0A

[@rolandburrows4859]

Joshua Bardwell thank you.

[@adriancjones]

Hey Joshua. I had to delete all of my models from the SC card and the radio because it made the radio go into an emergency mode.

[@JoshuaBardwell]

This means there is something in one or more of the models that is incompatible with the T16 radio. For example, if you had a model that was referring to an internal multiprotocol module or something.

[@bronson0066]

JB is correct!! This should fix you up. m.kzbin.info/www/bejne/m4eaeXytacl4oNU

[@vovsen123]

You need to turn of RF module in Open TX companion before copy the models and then add it manually in the radio

[@eskrace1104]

A little heads up ^^ Only Amazon got it available now on the links. All the others are either on pre-order,sold out or not there yet.

[@JoshuaBardwell]

It's selling so fast that everybody is running out of stuck. RaceDayQuads and Rotor Riot had stock literally yesterday.

[@KLNYC]

can do same with qx7?

[@ehunter2010ed]

I been wanting too ask you this question for awhile & the video is perfect for my question!! When you 1st started flying were you always a pincher or did you transition from thumbs too pinching??

[@DrDiff952]

Will the Amber voice pack work on the T16?

[@JoshuaBardwell]

Yes.

[@FPVish]

Is this still the radio you would consider to purchase today ? Still your best daily driver?

[@JoshuaBardwell]

Yes.

[@JohnDBloch]

I've heard that "From now on, Frsky will no longer supply goods for anyone who are selling Jumper T12/T16." What are your thoughts on this? Will you address it at some point?

[@JoshuaBardwell]

Do you have a source for that?

[@ernie5229]

Does anyone know how to bind the Jumper 16 to either DSM2/x or FlySky? After hours of work, I can't figure it out. I'm new to OpenTX but have 20 years in the hobby.

[@mikethomas7763]

Use Mult FS 2A for flysky but I'll let you know I'm have trouble of loosing bind when switching models.

[@AsTheRavensGather]

Mine is on his way🤘

[@stevenunderwood.]

Hi. Has any one bound a corona r6sf rx on sfhss having few problems.

[@madforit9661]

At 12 mins 8 sec I don't have telemetry in my menu, Is there a reason why?

[@vikingdane9757]

Wondering the same...?? Maybe no models installed yet?

[@Rob-vt1mz]

Same problem here

[@richardlong3615]

Why is it that your voltage telemetry VFAS and my voltage telemetry is CELS?

[@rscarawa]

Maybe there is a setting under d16 to get only 8 channels?

[@squeakyarcher2946]

If it's like the t12 I think there is a d16 8ch option

[@JoshuaBardwell]

ohhhhh it's a separate sub-protocol isn't it.

[@MCsCreations]

Fantastic, Joshua! Thanks a lot! 😊 And, well... Let's hope the Betaflight devs do it soon enough. 😊

[@Cult1022]

what keeps me off this radio, is my receivers: All the 5" are one CRSF and all my whoops are on the FrSky... so now I would need to carry 2 modules with me to fly all my stuff. And I guarantee I will lose the one module which isn't in the slot.

[@petarnedic855]

Excellent video! Thanks !

[@5thdimensionfpv390]

Does crossfire lua work on this?

[@JoshuaBardwell]

Yes, it does. I've used it.

[@piranha32]

Liviu's teardown shown that the radio has a board ready for an internal receiver. I guess soon we'll see a T16V2 with an integrated antenna and the board populated with the internal transmitter module and its accompanying components.

[@Temporal_Flux]

D16 8ch should be one of the FrSky sub-protocols. Scroll past D16 and past D8.

[@paulappleton5423]

When hall effect gimbals are standard I might switch but my QX7S is my baby at the minute

[@TealcJack]

I listen to you and always learn something I have never heard before. "Lua or Louis (not sure what you said) Scripts and Beta Flight Lua Scripts." What is the world is that?

[@JoshuaBardwell]

kzbin.info/www/bejne/qWKyXpuXj7KFrJY

[@andrewjamez]

It would be nice if Jumper gave a opentx config for the way it looks as promoted because that looks badass

[@JoshuaBardwell]

It's just a telemetry-based lua script. You can download it and run it yourself. Ummm... I don't know where the link is though.

[@Grumpyoldtwit]

You lost me around the 10 minute mark... :-( Where did 'document2.otx' come from?

[@Chuck_Carolina]

I love the black and white video at the end.... it was so creepy!

[@h2o-fpv623]

Yea I will flight it very soon thank u for the video.

[@filiped7298]

Only thing missing for me is the amber sound pack. But it should be an easy fix.

[@JoshuaBardwell]

Hmmmmm damn you're right. I overlooked that because Amber always comes over with my SD card contents.