Kawasaki Ninja ZX6R Exhausts / Every Question Answered / 2025-2009 / Removal, Install, Servo, CEL

[@sherwood_01]

I’m serious when I say this guy might be the most informative KZbinr on KZbin. He’s not afraid to drop 25+ minute videos about actually relevant information that would benefit a consumer in today’s market. Well done man, you earned a subscribe and a lifelong follower.

[@lovelivegofast]

Hey thank you man, I appreciate it! 👍

[@Forwardoperationbase]

@@sherwood_01 i say lets keep him a secret just for us 🤭

[@Borchers859]

Just saved me a bunch of money man, I was fully expecting to drop 1000+ to get that sound 😂. Big help, just bought my 2024 yesterday and I’m pumped!

[@lovelivegofast]

Awesome man! 👍

[@joeboomstud]

As I’m watching this with great frustration, I’m now grateful to see you remove the expansion chamber. I could not get it to budge at all. Tomorrow is a new day!

[@lovelivegofast]

Yeah just back and down, it's tight but it will slip outta there 👍

[@joeboomstud]

@@lovelivegofastI really hope so. My Allen wrenches are in one of those pop out sets. I may need something better with more leverage. I tried for 2 hours tonight. You give me hope. As for the servo. I saw that tonight and was like wtf is that. I may have violently pulled it from the stock pipe. Oops. Anyhow. Links are here and now I have hope and pipe comes tomorrow. Picked up my 24 zx6 last week. So excited. Dropping 2 inches. On that note, do I need to make any adjustments to the suspension after that drop?

[@lovelivegofast]

You won't need to adjust the suspension settings to maintain the same ride quality with lowering links, should feel the same. It will corner and handle different in the twisties though because it does slightly change the geometry of the bike. If you haven't had a chance to really throw it around you won't notice a difference 👍

[@stormy_yt]

For 90$, that's an impressive result. Good Upgrade dude

[@lovelivegofast]

I think so too, thanks man!

[@VizVlogs]

I am once a vlogger and I think I would need to get my 4$$ back because of you. I was inspired first by DoitwithDan around 2017 and now 2024, you did the same. Watching this coz I am thinking of getting zx6r, not so soon yet but I feel excited just by thinking I have informative videos from you. Hoping to see more content like this. Practical. Informative. No wasted time by cutting out what's not needed. You answered all my questions in a long 25min video. You deserve far more subscribers than you have right now. EDIT: I subscribed after watching this video. 1st one was when you changed oil of this beast.

[@lovelivegofast]

Thanks man! Happy to help, I'll keep cranking out the videos 👍

[@Screenwriting]

Such an underrated channel! Great job!

[@lovelivegofast]

Thanks!

[@drakegilberto7604]

Just btw, not saying anything is necessarily wrong, but it can take up to 100 miles in some cases before the ecu re-checks all sensors in order to throw a code or not, sometimes just resetting the battery works too but not always

[@Forwardoperationbase]

BROOOO i love your videos. I bought the black leather jacket you have in other videos. Im also going to do everything you did on this video when it come to my exhaust

[@casualtactician9537]

You made that resonator look pretty easy I’m currently fighting it!!!!!

[@JogabonitoAj10]

I bought the M4 street slayer slip on. It sounds EXACTLY the same (without baffler) as the slip on the guy used in this video. Save your money, $100 vs $400. It is VERY loud, if you don't mind the noise, keep it. I recommend trying out the muffler with decible killer that this guy has a link for, BEFORE spending $400

[@newbugatti7842]

Dude, this was extremely knowledgeable and well thought out and seriously kudos fantastic video for anybody wanting to do their own work on their own bike

[@lovelivegofast]

Thanks man! 👍

[@TheBoggledMind]

I have good news and i have some bad news, good news is i can confirm on a 2023 zx6r that keeping the servo plugged in does not throw any codes or prompt an engine light no servo buddy needed. Now for the bad news, that last bolt you had trouble with on the expansion chamber also is giving me one hell of a time, it snapped my allen key so now i have a tip of an allen wrench wedged in there so now I am stuck trying to get that thing out.

[@SamSchmidt90]

sounds soo good, take us on a ride with the new exhaust

[@lovelivegofast]

Should have that video by this weekend 👍

[@MotoEscapade]

Love your videos man , I have the same bike but KRT Edition , that bike sounds insane, Congrats

[@lovelivegofast]

Thanks man! It's been super fun to work on

[@Vanz73]

Thanks for the video its very helpful, picking up my pearl white 25 ZX6r -ABS tomorrow.

[@jeremykopatz4760]

geez...my 6MM bolt for the resonator chamber part came somewhat stripped by the factory! I have to call a friend over with mechanical wizardry to hopefully help me find a way to get it off. I got everything off just fine, even the 6mm bolt just below the tough one, so I know my hex size is right. What sort of monster put this thing together?!?! Edit: My friend used a hammer to bang the hex socket into that slightly stripped bolt and was able to get that monster off! Also prying that nut out of the metal housing on the back of Res Chamber was much harder on my bike than the video, I ended up having to Dremel saw it open enough to get that nut out! Everything else was exactly like the video, thank you very much for the help here!

[@ddawson1976]

It's been a while since you removed the stock exhaust. Just want to verify that you have NOT had any code issues by keeping the servo motor plugged in. I'd rather leave in the servo motor and save the money by not having to purchase a servo buddy.

[@lovelivegofast]

Yep no codes, all has been perfect 👍

[@MarcoTernavasio-pv3ec]

I've bought one 2 months ago and i'm so happy! Wonderful bike and the original exaust sounds really good. Remove the valve is not a good idea, you need to remap and lost a lot of torque at low rpm.

[@JogabonitoAj10]

Just did it and it sounds great! It is very loud, sorry neighbors lol 😅

[@Backtothehat]

Video liked after 35 seconds in. I could tell just from the start, I will learn something.

[@BLG-b3q]

Very informative! My expansion chamber won’t come off. Probably going to have to drill the bolts to get them out some the Allen key has stripped them from my tugging at them

[@lovelivegofast]

Dang, idk why that Alan head bolt is on there so tight! Like it's ridiculous

[@Forwardoperationbase]

Bro! This channel is the shit man!! I appreciate your work

[@lovelivegofast]

Thanks dude 👍

[@Forwardoperationbase]

@@lovelivegofast please keep the zx6r vids rolling. I just bought a 2025 krt and Im going to say your videos where a huge influence.

[@williammarthianus1212]

very good information tutorial all in one package lol you are a lifesaver

[@lovelivegofast]

Happy to help! 👍

[@theprodigal7143]

Hi, any update if there was any loss of backpressure? Thanks bud 👍

[@theprodigal7143]

Hey, i was just about to disassemble the cover, and one of the bolts requires a torx wrench. 😢

[@abrahamvelazquez3843]

Awesome video!

[@calvinmarty4528]

Subscribed! I just bought this exact same bike and Im in love!

[@lovelivegofast]

Awesome man! It's a great machine, I love it more and more everyday

[@ericjones9257]

How's the bike doing?! I'm thinking of getting it.

[@casualtactician9537]

Thanks man hopefully I can just change my M4 slip on from my 2012 zx6R to my 2024 636 then I will be good without a servo buddy and not spend anything hopefully they say I’m all good 🤙

[@JoshuaUrrutia]

Wow vi como mil videos y este fue el mejor de todos todo claro y súper bien explicado Solo me da miedo cortar los chicotes del servo. Pero pues con todo menos con miedo. Great video

[@Garmr2000]

I gotta get me a Zx6R 2024 this year. As much as I love my first gen R6, I gotta have a fuel injected bike to enjoy the best of both.

[@olaolaola167]

I tried this and followed this to the T, even got the same materials, same fender eliminator from another video, etc. Once I got to the factory link pipe / muffler after removing the exhaust, I found an o2 sensor on it, mine has two sensors. One in the muffler, at the beginning, right after the catalytic converter, and another before the catalytic converter. Maybe it’s just an Europe thing?

[@ddawson1976]

Just reading through the comments and came across your post. I recently received my Racefit Growler X exhaust and plan on installing it this weekend. My exhaust came with a spot for a 2nd O2 sensor. My 24' ZX-6R only has one. I spoke with the owner of Racefit (In the UK) and the Euro bikes DO have two O2 sensors. It must be a Euro thing. I have to have an O2 plug in my exhaust because the US models only have one O2 sensor.

[@boscodomingo]

It does have 2 O2 sensors for the Euro5+ rating. I guess it's a matter of drilling a hole in the new link pipe to put it in? I bet there's sensor deleters too

[@zinamogaming5589]

I just replaced the entire exhaust system and I’ve been running the bike still. Am I messing it up? Is me having it not tuned ruining the bike?

[@JohnCosper-u8t]

the video is 6mos old is there any update to if the engine code came up after riding without the servo cables but leaving the servo still plugged in?

[@lovelivegofast]

Never got a code 👍

[@johny.3218]

Those decel pops sound pretty nice for a $35 aftermarket pipe. I was thinking about spending $2k for a SCP-CRT full exhaust but I might actually opt out for a $35 pipe hahaha!

[@lovelivegofast]

I'm sure it's making everybody re-think their high dollar exhausts lol

[@jayilla28]

OMG that sounds amazing, great video

[@tredbailey]

Mines is on there super tight. Felt like I was going to break the allen key or strip the bolt

[@lovelivegofast]

Some people have. Seems like everyone's is on there crazy tight

[@JosueRodriguesDeCarvalho-gs4fe]

Excellent video

[@lovelivegofast]

Thanks man 👍

[@I_am_wrath_zx6r]

What is the diameter of the cat? I see some link pipes with 51mm and others with 54mm. What size is that snail link pipe?

[@magentacrayolas1585]

Smoked my carbon ring a few nights ago, wish I seen this sooner!😢😂

[@lovelivegofast]

Me too!

[@krew7687]

What is carbon ring? Curious, new to bikes,

[@lovelivegofast]

These bikes have a graphite ring that functions as a gasket between your exhaust pipes where they overlap and go inside one another

[@krew7687]

@@lovelivegofast thanks for the reply, have the same bike, and fortunately I haven’t lost my carbon ring

[@Forwardoperationbase]

Hey brother, is the engine light still off 8 months later ??? Update please 🙏

[@lovelivegofast]

Yes 👍

[@jayilla28]

My only question is with that pipe being so close to the tier did it give you any heat issues?

[@russianguy212]

Do I really need the curved connection/ link pipe for back pressure I think you called it? also it just looks so close to the rear tire is that also not an issue with the link pipe you used?

[@heftytbag9637]

When you put this exhaust on did the exhaust fit into the cat like 100% snug? I just put one on a friends bike and there is a little bit of an exhaust leak where the turn pipe goes into the cat. The carbon seal is still intact.

[@lovelivegofast]

Mine is 100% snug and tight with no leaks. Maybe check and see if the exhaust clamp is tight enough

[@tomvanwalleghem8593]

Great video!

[@lovelivegofast]

Thank you man!

[@ferolivasosa]

DId you have to weld anything at all from the mid pipe to the CAT? or does it just fit right into it? '

[@lovelivegofast]

No welding, everything is a perfect fit 👍

[@TheRichellis79]

Question; did you ever get an engine code from removing the cables from the servo motor? I’m about to attempt this process on my ‘24 zx6r

[@lovelivegofast]

Nope never did, servo still plugged in with no cables

[@TheRichellis79]

@@lovelivegofastthanks buddy! Loving the videos, keep up the great work! 🤙🏼

[@NoMexicanas]

My exhaust fell off do you know what bolts I need to order

[@unstoppable2131]

Thank that's so informative. I have a question. What if I let the expansion chamber intact and just put on a slip on exhaust. Does it make a great sound? Or do I really need to remove tha expansion chamber?

[@lovelivegofast]

It's the same sound, just barely a bit quiter. The audio doesn't come through great on my cameras so I couldn't tell a difference on film. I'd throw one on with the chamber intact, if you want louder, then just get the $55 link pipe that removes it. My setup is really loud though, like extremely. Depends what you want

[@unstoppable2131]

@@lovelivegofast thank you I would do as you say.

[@Zx6rBlue]

With a complete system change, do i need to do anything to the ecu/ mapping?

[@lovelivegofast]

I'd get a flash if you do a full system. You might notice a slight dip in low rpm power, depends what system you go with. But you won't gain any power until a flash or tune, then you should see 12+ hp

[@gavinclark6948]

Would I be able to mate that link pipe that deletes the resonator to my akropovich slip on?

[@lovelivegofast]

Yes, any 2" or 51mm slip on exhaust that just has the hooks and is held on by the two springs will fit on it 👍

[@lovelivegofast]

Measure the inlet on ur akrapovich to confirm but I believe it is

[@dr_superior8505]

Quick question what made you switch to the other muffler? Just too loud after decat/ecu flash?

[@JamesB58]

hey man did you ever end up getting a check engine light im thinking about doing this because im watching a few different videos and they say you get a check engine so im confused

[@lorenzodigiovanni2419]

hi man, if i put a slip on with mid pipe that removes the expansion chamber do i have to flash the bike ? will the motor be hurt if i dont? thankss

[@lovelivegofast]

No you do not have to flash it 👍

[@Moto_Rid3r]

Hey Bud. I was watching your video about taking the servo cable only on the servo with your after market exhaust. Did you got any check engine light lately since you install the ebay exhaust?

[@lovelivegofast]

Nope, just remove the cables and leave the servo wires plugged in and ur good to go 👍

[@leiwie7722]

do you need a link pipe coming off the expansion chamber?

[@lovelivegofast]

If you want to keep the expansion chamber and put a muffler on, yes, you will need the short link pipe

[@loganchance5815]

I'm strongly considering running this on my zx6, but my main question is, does that exhaust and tip rub up against the swingarm at all after hitting bumps? Was a little worried about if there was any issue with clearance for everything.

[@lovelivegofast]

No issues with clearance, it's not even close 👍

[@infa1v1ous]

If I already have a slip on (Leo Vince LV-10) will this mid pipe (twisty pipe) resonators delete work? My slip on connects to the bracket of the rear peg

[@theprodigal7143]

Did u ever find out? I have lv one evo,

[@infa1v1ous]

@@theprodigal7143 Unfortunately I did not. I planned on just adding a SC Project Midpipe or possibly a Akropovic Mid Pipe

[@theprodigal7143]

@@infa1v1ous will it require a tune?

[@infa1v1ous]

@ not unless you get rid of the cats

[@badazvw]

Will the parts in link work on a 2025

[@lovelivegofast]

Yep 👍

[@waltermanzanero3]

Question I feel air coming out where the cat is located at did I miss a step? Or is that okay?

[@lovelivegofast]

Is the clamp tight? Did you get your graphite gasket ring back in? I have no air coming out of mine

[@metalman3018]

Will the shorty hook straight to the header?

[@xAnimeID]

Did he use the short link pipe for the resonator in this video ?

[@lovelivegofast]

I didn't show it in the video, it was the same volume without the expansion chamber and I wanted to drop the weight of that chamber

[@vinnymariante8501]

The link to the mid-pipe says it doesn’t not fit a 24 ZX6R with abs, did it say that to you too? Awesome video, thank you for the help!

[@lovelivegofast]

It'll fit perfectly 👍

[@ZachMan99]

Would I have to get both link pipes you put in the description or can I just get the short one and the muffler?

[@lovelivegofast]

If you are keeping the resonator chamber you can put the short one on that, but the short one won't go straight on the header, you'll need the curly one if you remove the resonator box

[@locallowergaming5103]

Could you post a link to the eBay link where you bought them?🤘

[@lovelivegofast]

They should all be in the description 👍

[@emantv8113]

Is there still no check engine lights? I just ordered servo buddy today dang it

[@lovelivegofast]

Yeah still no lights, and I've put 500 miles on since then

[@emantv8113]

@@lovelivegofast well… time to install lol 💪🏽💪🏽💪🏽

[@lovelivegofast]

Good luck sir

[@GeoMoto]

After delete catalyst need tune ecu or it will not engine problem and can ride?

[@lovelivegofast]

If you have a curly 360 link pipe like I put on, you don't need to. If you delete the cat and have a muffler that comes straight off the header, I would if I were you. You can still ride it but eventually I would get a tune so you're not running too lean

[@GeoMoto]

@@lovelivegofast i have m4 gp19 and today deleted catalyst

[@lovelivegofast]

Nice man, I bet it sounds wicked! You'll pry want a tune eventually with that exhaust. I'm sure it's shooting fireballs now 👍

[@steelcitycaprice.899]

👍🏽😎🏁🏁🏁🎵🎶🎵🎶 got two on my 0610r🔥🔥🔥

[@lovelivegofast]

I love my 2006-2007 zx10r's. They are as brutal and untamed as it gets 👍

[@ScooterNinja]

Is there a way to make bike loud by using the stock exhaust? i mean just remove servo cable and by default that butterfly valve is always on and remove the breadbox and put a linkpipe with stock exhaust.. will it work?..

[@lovelivegofast]

So I think you could do the link pipe to the stock muffler with the servo cables removed. But 90% of your sound dampening is in the muffler, so it will be a little more volume, but not much. The link pipe to delete the bread box is $65 and a no name mufflers is only $35 more. What is your reasoning in wanting to keep the factory muffler?

[@ScooterNinja]

@@lovelivegofast I saw a fellow versys rider do that... And it sounded great... Actually here at my place sometimes police would do special drives and if caught they would seize your bike with aftermarket exhaust .. then you have to pay fine upto 250$ if i convert to USD 😂

[@mavricxx]

If you do aftermarket headers, it should sound louder while keeping your stock exhaust and deleting the mid pipe.

[@Loowenka]

Does it have a clutch

[@lovelivegofast]

Yes it does

[@simplem4376]

What kind of springs did you get ? How long were they ?

[@lovelivegofast]

Just the springs that came with the muffler

[@leiwie7722]

where can i find the ring....

[@lovelivegofast]

www.kawasakipartswarehouse.com/oemparts/p/kawasaki/11061-0448/gasket-54x62x30

[@leiwie7722]

@@lovelivegofast youre the best

[@B5th3f4st49]

Im confused is your exhaust 2 pieces or 3? You have 3 links in the description.

[@lovelivegofast]

You only need two pieces. There's two different link pipes because one is to be used with the resonator expansion chamber and one deletes it

[@B5th3f4st49]

​@@lovelivegofastyour videos go above and beyond. I ordered the slip on and link pipe in the description of your oil change video. Is that all ill need?

[@lovelivegofast]

Yep, nothing more needed. And you will be so pleased with the sound and look! Thanks man 👍

[@B5th3f4st49]

​@@lovelivegofastsorry i have one more question. Theres no mount? Its only held on by the springs? Thats not an issue?

[@lovelivegofast]

With the link pipe being so short and having a firm mounting point on the frame, it's very solid without any sort of a hanger. Just the springs are good

[@AnguishBarbarian]

this video is giving me 'cut springs on a civic' type vibes

[@lovelivegofast]

Excellent 👍

[@jeffsmallwood4636]

Awesome Bro!

[@lovelivegofast]

Thanks man 👍

[@Gage-ug6xn]

Your cel still hasn’t came on?

[@lovelivegofast]

Nope, no light

[@jokacz123]

I think that the misconception that the expansion chamber is the cat comes from the fact that on the ZX10R it is the cat. Gutting the cat in the ZX6R header is a major PITA and is best done off the bike. You will need a flash/tune and even then it's not a substitute for an aftermarket header/full exhaust. Hindle makes a good full exhaust for those on a budget, don't waste your money on an Akra or SC or any of the poser exhausts, al they get you is bragging rights.

[@BrothaBanye]

Is there anyway to contact you outside of here? I have questions lol I’m from DE and have the same bike I just purchased last Friday!

[@lovelivegofast]

Wacha got questions about?

[@BrothaBanye]

@@lovelivegofast did your light ever come back on? The exhaust set up will be here tomorrow, and did you change that slip on? From the original you had placed on there first?

[@lovelivegofast]

No exhaust light ever came on, was just riding more today and everything is perfect. I still have this muffler but I have since gotten a different Amazon muffler that has a removable decibel killer since I live around a bunch of old people and families, I work late nights right now. I just posted a video today of the muffler I currently have on it. Sounds the same but I can put that DB killer in the end and make it quite when I need too

[@BrothaBanye]

@@lovelivegofast def hard to gauge from a video, sounds good, and if I didn’t find your channel I would have def dropped 2k on top of the 8k I dropped on the new ZX lol I just need to know if this is going to piss my neighbors off 😂 I live in a super quite neighborhood and half the people are old and retired 😂 and my wife**

[@lovelivegofast]

They will know when u leave and when ur coming home is what I'll say lol

[@brandonperez5546]

Thank you 🤝

[@lovelivegofast]

Yes sir!

[@Sammyalqattan]

does it still sound good after 12 days? lol cuz this is way cheaper than the M4 and sounds amazing

[@lovelivegofast]

Sounds better everyday!

[@SuperKnightwind]

hows the servo motor doing lately?

[@lovelivegofast]

Still plugged in, still no engine lights

[@SuperKnightwind]

Cause im planning to buy zx6r 2024 too.. From the Philippines by the way.. 😇

[@SuperKnightwind]

@@lovelivegofastdude got mine removed and having no problems.. thanks for this video

[@lovelivegofast]

Awesome man! 👍

[@fichtl18]

Thanks very much for the information with the servo!🫶🏻

[@lovelivegofast]

No problem, I figured it would help some people out

[@Hl-uy3sz]

Looking for my first bike 😂

[@CarlosJimenez-rm9ly]

I want this whole setup….like noowwwwwwwww

[@lovelivegofast]

Well if you got $90 it could be yours!

[@CarlosJimenez-rm9ly]

@@lovelivegofast currently looking into ordering everything, and also you got yourself a new sub, thanks alot this super useful! underrated channel!

[@lovelivegofast]

Thanks man!

[@flashines2]

do you need to tune with this setup? any difference in performance?

[@lovelivegofast]

No tune needed, no difference in performance, just sound 👍

[@xAnimeID]

considering they're race bikes, they don't half make the exhaust a nightmare to change

[@enniocancellieri8680]

TOP!!!!!!

[@FrauStormm]

That 6mm hex is tight as hell on my resonator as well 😭 couldn’t even get it off with my t handle

[@lovelivegofast]

Yeah you will need an "L" shaped hex key with a little pipe or a socket and extension on it. It's a bugger

[@robertanderson6803]

there's no point in doing ANY exhaust work if you're not planning on getting the ECU flashed.. there is literally zero gain and all you did was make the bike louder. that being said, if you do get a FULL system (the only worthwhile exhaust upgrade) and have the ECU flashed to that system for max benefit, they can tune out the servo so you wouldn't need a servo buddy anyways. they'll also tune out the AIS/smog system and the o2 sensor so you'll be free of CELs and all the restrictions and their weight in extra parts.. i dropped over 30lbs between the exhaust, lightweight antigravity battery, servo motor, passenger pegs, mirrors and rear signal/plate/undertail crap.

[@lovelivegofast]

There's plenty of perks to our exhaust job, great sound, dropped weight, looks a lot better. If you want to be wicked fast just get a liter bike

[@robertanderson6803]

@@lovelivegofast there's plenty of potential in these bikes and many dyno videos to prove it. while you're absolutely correct in everything said - it's a shortcut. in removing the servo motor completely, you're not only dropping weight, but making space too so you have at least some semblance of a trunk. my wallet and phone now fit. a proper tune makes the bike run better everywhere as well. you're option is a good *start and i appreciate the content.

[@lovelivegofast]

Yeah for sure, just depends how far you want to go with a 600

[@marcosnunez6844]

Hola. Me encanta tu vídeo. Por qué soy un piloto de tu talla😂. Me gustaría que le hicieran una reseña a la Kawasaki ninja 636 zx6 2024.

[@everythingenfield8903]

Sorry mate, stopped watching after 2 mins....bell end.

[@MrSay2801]

So your engine light never comes on ?

[@lovelivegofast]

Correct

[@NcRPredator]

My screw legit stripped 🫥 i

[@Gage-ug6xn]

Your cel still hasn’t came on?