Kite Dlg Built Log Part 1

This is the first part of the Kite RC glider build log. Follow along on your own Kite DLG build, or use this as a guide on your other glider builds. In part 1, we install the spring for the elevator and rudder, control horns for the wings and tails, as well as the T-blade on the wing.
Kite DLG: bit.ly/kitedlg
CA applicator tips: bit.ly/catipsusa
Sequre Electronic Screwdriver: bit.ly/sqes126
Diamond Burr Bits: amzn.to/3DJerR6
My ultimate tool guide for DLGs: bit.ly/dlgtools
Deviant throwing blade installation template: bit.ly/deviantb...
ArmSoar: www.armsoar.com
ArmSoar USA: www.armsoarusa.com
Resources / What I Use
KST X06 Servo (International): bit.ly/3v6xAr6
KST X06 Servo (Canada & USA): bit.ly/x06usa
KST X08 v5 Servo (International): bit.ly/kstx08v5
KST X08 v5 Servo (Canada & USA): bit.ly/kstx08v...
Wire For Pull Strings: amzn.to/3eykaO7
Crimps For Pull Strings: amzn.to/2QbSLta
5mm Gap Seal Tape: amzn.to/3v1d3UE
Kapton Tape: amzn.to/2QjwSIf
Spektrum AR6610T Receiver: amzn.to/3is4uiN
Spektrum AR410 Receiver: amzn.to/3n3BhLr
Spektrum iX20 Radio: amzn.to/3dwPcq5
FrSky GR6 Receiver: bit.ly/frskygr6
FrSky R6 Receiver: bit.ly/frskyr6
FrSky X20 radio: bit.ly/armsoarx20
FrSky X20S radio:bit.ly/armsoar...
I hope you find that useful! Just so you know, ArmSoar may collect a small share of sales from the Amazon links on this page. It doesn't cost you anything and helps out our channel.

[@rapharigoti]

Thanks for sharing building of your fantastic DLGs Thomas!!

[@ArmSoar]

My pleasure!

[@kev4354]

Very good tutorial, good camera work, and very well explained with some good tips, keep them coming- Thanks

[@ArmSoar]

Thanks for watching! We'll continue making more :)

[@simongroom974]

Excellent adhesive technique!

[@bigboy760yee]

Very good build. I will be using this video when I'm ready to build my first dlg. Thank you!

[@ArmSoar]

Glad it was helpful! Welcome to the DLG world.

[@ArmSoar]

Is the Kite shiny or what???

[@sebs8807]

Damn You have really great build videos!!!

[@ArmSoar]

Thanks for the kind words!

[@TitofBee]

it's a nicely made and designed glider, i hope it flies the same.

[@ArmSoar]

Looking forward to the maiden flight in a few days.

[@elwynj5379]

Fantastic tutorial… looking forward to part 2….

[@ArmSoar]

In progress :) stay tuned!

[@ChristieNel]

For the spring holes, I took out the springs and ran some thin CA down the hole to harden it. Then you can also remove the spring again in the future. I don't know how much of the thick gorilla glue makes it all the way down the hole.

[@ArmSoar]

We've used thin/superthin CA for years, but have switched over to the white Gorilla glue a few months ago as we find it does a much better job at minimizing skin print-through.

[@ChristieNel]

@@ArmSoar Wait, the Gorilla glue was white (PVA?) glue and not Gorilla superglue?

[@ArmSoar]

@@ChristieNel it’s an expanding/foaming glue.

[@bstearn1653]

Very nice.

[@ArmSoar]

Hope you enjoyed it!!

[@MissurayLaslo]

Nice work🤘

[@ArmSoar]

Thanks!!

[@duoviss]

hello, what kind of powder to use with glue

[@maksimbondarevskiy5202]

when will the 2nd part of the tutorial be?

[@ArmSoar]

We're working on the VO, should have it published tomorrow or Wednesday.