How To Make Digital Temperature Controller

[@vladimirvavrik7760]

Excellent construction! I made it. Just a small mistake. In the code, pin A5 is written, but in the diagram A0 is connected. After correction in the code everything works great. I have a subscription to your channel my friend. You're doing a great job. Greetings from the Czech Republic.

[@abeditani8293]

I like your channel because you making it easy and you do the project as you do it with out hide anything . 👏👏👏👍👍

[@MarloTechWorld]

Why did you put 4 push buttons but the diagram has only 3 push buttons? Which digital pin should i solder the fourth one?

[@sanjaybatra6593]

pin 11 has scope to use for 4th button , no code is supporting this button.

[@MojsterMijagi23]

hello! i have a question for your project. I am curious about your relays logics and how did you physically connected them. Which relays connector you connect voltage beacuse if i understand right the heating and cooling are diffrently connected(one is connected to normally open and one to normally closed)? otherwise cool project!

[@gaidenlee]

Is their an insntance to make the limit temp value to be negative?

[@MaxGoddur]

How do you stop the temp from oscillating above and below the setpoint?

[@dejanpetkovski8761]

Hi Kiyani's Lab i need this only fo heating controll did i must make a cooling too or not. Thanks

[@KiyanisLab]

for better result you need to add cooling too but is can be work with only heating if the environment is not to hot you can only use heating

[@dejanpetkovski8761]

@@KiyanisLab I only like to control Water Heater for entire hous so the digital temperature controler will be be placed on the hallway and when the given temperature is reached it will cut the heating.

[@shreyanshgupta9431]

Can I use this for refrigerator?

[@habilekgopti9449]

something is wrong bit you are the best youtuber up

[@melplishka5978]

Very well done. Exactly what I was looking tyvm. Very well explained too.

[@yousaftoki1599]

Amazing bro

[@marform75]

Very interesting project, i will use it for my aquarium. You think that in the future you will design a conductivity meter? Greating

[@deanroy1747]

instablaster...

[@MuhammadArslan-vl7ln]

Can we use Arduino UNO for this ?

[@caturhermawan2190]

can the thermistor be replaced with a thermocouple?

[@KiyanisLab]

yes but we need to use voltage amplifier for that can be made with opamp

[@sanjaybatra6593]

@@KiyanisLab if we use pt100 , which IC will be suitable for it ? MAX31685 ???

[@sanjaybatra6593]

I have notice that 4 buttons have been used in code , but in your code and circuit diagram .. you have only shown three buttons ? something missing ? I don't understand the use of variable "m" in code. when the value of "m" will reach 1 ? (m= 1), when we press button 8 and variable "x" reaches 300 ?? if(x==300) it means loop() will complete 2 rotation and move to 3rd rotation. please clarify doubt.

[@Aniketdada2004]

Bro i want how you connect 💡heting divice & fan to the circuit

[@KiyanisLab]

you need to connect the line wire of the device to NO terminal of the relay and connect main line wire to COM terminal of the relay

[@Aniketdada2004]

@@KiyanisLab how it's connection in Paraller Or in series

[@Voice.Of.Nation]

Good channel...👌

[@newvaper3794]

hello kiyani....thanks for the video....i am doing a diy smd hot air....the hot air handle has 2 thermocouple wires...how can i control the temperature of the heating element of the smd hot air blower? thanks.

[@jagjeetsinghmankoo7137]

you are best as always

[@MarloTechWorld]

Sir, thanks for the video. Am only seeing the limit temperature, how can I set the minimum temperature? Or how will the cooler and the heater be turned on and off if you set the limit? I want to use this project in the egg incubator.

[@mbos8791]

Hallo Kiyani, er staan 3 Push Buttons op het schema. En U sluit er 4 aan. Ik neem aan dat de vierde is voor de reset.

[@aanagasin]

Cool. Can be setting for ramp and soak program?

[@asimtanha7287]

Very nice sir g thanks

[@Aniketdada2004]

Bro i want to know how you connect heting device 💡bulb & fan to circuit Please bro tell me how you connect💡💡💡 🥺🥺🥺

[@arahmankabir8405]

Very Nice project. How to set 3 wire PT100 Temperature Controller in this project

[@sanjaybatra6593]

I have same question , if you have any information , do let me know.

[@pubgmobail7397]

My brother, I have implemented the scheme, but it is not working well. The temperature is 210. Can you help me?

[@rezinaakterrumi6775]

@Sabertooth Alpha nhi Bhai

[@rezinaakterrumi6775]

@Sabertooth Alpha Bhai ye project me kab se banane ki try karrahahu lam nhi karata code

[@rezinaakterrumi6775]

@Sabertooth Alpha main try karunga kisi coder se ye check karanekeliye

[@Aniketdada2004]

Tum logo ga hua kya mera temprature 200c above aa raha hai

[@Aniketdada2004]

Abhi kya kare

[@allabouttech5689]

Hello sir, I have stop by to watch your video and it's very informative. Anyway I'm new here. Sir can you build digital temperature display like that one of KOOCU 852D rework station

[@KiyanisLab]

yes bro i will make

[@allabouttech5689]

@@KiyanisLab Thank you very much for your reply..Sir let me summarise everything to you, I didn't mean you should build the rework station but rather when you start turning the potentiometer clockwise it should be able to start displaying the digit from 200,250,300,350,400,450 and 480 on 3 to 7 segment display led

[@joseluisblancoalfaro]

excelente video

[@anuradhacreation361]

Please one video digital tamputre contrul soldring iro station sir

[@KiyanisLab]

ok bro

[@hirdeshbajwa8906]

What is the temperature probe you used? I have the ds18b20

[@vivaan420here]

Can i use 100k ntc thermistor here?

[@musaberashid5927]

Did you program the arduino nano using a computer

[@KiyanisLab]

yes you can

[@panthLeoJTm]

Hi, Sir, I tryed to use the code you put below but It doent work. What is your advise to me?

[@KiyanisLab]

check the connections of the circuit

[@arahmankabir8405]

Please create a project on dyeing machine temperature controller

[@smultimediasg]

Pls make battary charger with 3 stage charging system that charge lead acid , li ion ,lifeo4 battary . Thanks

[@Aniketdada2004]

Bro yaar mera temprature 200c above bata raha hai help mi bro mere liye ye banana bahut jaruri hai please yaar replay me🥺🥺🥺🙏🙏

[@KiyanisLab]

trim pot se adjust karo bro

[@nighatshaheen8905]

sir , my LCD wouldn't show the required reading. why is this so?

[@KiyanisLab]

1 adjust the brightness from trimpot 2 see the lcd connection 3 have you uploaded the code to Arduino

[@17aniketmenge45]

How to do coding in this arduino Or what's steps are thire

[@KiyanisLab]

kzbin.info/www/bejne/qnycnKV8rbmaecU

[@Aniketdada2004]

@@KiyanisLab thx🥰

[@joinmeandlearning9844]

Please help i make circuit temperature (Nagative -90°c ) ice cold control...

[@sanjaybatra6593]

you got success ?

[@tamilpuretech2505]

sir Please upload one vedio for sht31+esp32+oled1.3"+blynk+thinkspeak+button controler ( temperature and hummidity setting thereshold)+with calibration setting from button+centigrade & farenheit setting from button+temperature and hummidity high & low alaram using incubator.and egg turnning time control+ventilation controler from temperature based 0 to 180 degree.+data logger . thankyou

[@Aniketdada2004]

Bhai yar mene banaya lekin ardunio mese dhua aane laga uper se abhi ardunio ki tx, rx, or pwr led ग्लो kar rahi hai help me bro 🥺

[@KiyanisLab]

bhai aap connections chek karo kahe problem ha

[@arahmankabir8405]

Please do a project of Arduino Base pt100 3 wire Temperature Control

[@KiyanisLab]

yes bro soon

[@shoppingoneclick2044]

I am interested for same, PT100 based...if you have any information.. Please share

[@faridi-bin-Zouq]

bingo lovely.. I was waiting for such a lovely n useful project...will make it soon InshaAllah

[@e4es382]

Which software used for design the circuit

[@anwarpasha149]

Yes please let me about the software please

[@maniaksound5461]

Max limit temperature ?

[@desidance1059]

Thor chut

[@dayc3093]

How to add backup all temp data to excel in every 1 hour for ur project?

[@premsagar9839]

How to connect with lcd I2C

[@AsgharInventions]

can i use incubator

[@nishalyadav9800]

bhai please make a CNC writer by aurduino nano and motor driver shield

[@morganmystery9705]

My temperature wont go under 200 degrees Celsius for some reason, I can't figure out what to do but it just cools forever.

[@Aniketdada2004]

Bhai mera bhi temprature 200above dikharaha hai

[@Aniketdada2004]

brother you have to agjust veriable resister which is conected across sensor

[@Aniketdada2004]

brother you put wrone description for this video . you put (Hi friend in this video I have made an electronic component tester using arduino and a few more component I hope you learn something from this video please like share and subscribe) this but this project is temprature control device

[@marlonglodo1930]

not working the temp stayed 1125.6 celcius. all button not working

[@golantv273]

Is it PID CONTROLLER

[@KiyanisLab]

no its simple on off control PID one coming soon

[@simplydoing9596]

So fast not understand In every video if u explain your circuit needs, purpose, method of achieving, why these parts are needed, then viewers will understand more easily and learn just like in school learn with fun Its the problem of all youtubers that they just make video and dont make public understand why they fitted these components and etc...

[@Aniketdada2004]

Or ha vo aapane circuit me 3push button diye he or original me aapane4 push button lagaye

[@KiyanisLab]

3 use ho gai hardware ma ek extra ha

[@rezinaakterrumi6775]

Sir I cannot download the code

[@hhhuhhh5692]

What is the total cost?

[@nerdfluent7216]

~$64

[@nerdfluent7216]

Temperature is displaying 306C + no idea how to fix it

[@MarloTechWorld]

Try to use a 1K potentiometer instead of a 10K

[@RAJPUTPIARCHAND]

This item available

[@apollorobb]

You need to have a Differential or some sort of Hysteresis or the whole thing is useless

[@rezinaakterrumi6775]

Pls tell how to download the code

[@AqibFayyaz-EE-SectionA]

Sir plz send me a arduino programming code.

[@rezinaakterrumi6775]

And pls comment the code for me

[@morganmystery9705]

sucks

[@rezinaakterrumi6775]

@@morganmystery9705 what is your problem

[@ramukumar2875]

Sir how to include password.h library

[@MojsterMijagi23]

ŠIPTAR

[@dilipmore4339]

हींदीमे बोलो