How To Make Electronic Circuit Breaker | Over current Protection

[@ovalwingnut]

Thank you for the effort :O) I would have loved it if you spent the bulk of the time explaining the circuit's theory and operation as apposed to just "mechanically assembly the components". I'm sure most of us could figure that out. But the reason for individual components is what would be of value. Cheers from So.CA.USA 3rd House On the Right.

[@oskarsabo]

Super idea, now a breaker for 220v ac!

[@qadeer1685]

Good job

[@klong4128]

Another DIY with mini circuit breaker ,relay, ... Using 24 electronic components to prevent Overcurrent protection PCB board without FUSE .I rather buy the completed PCB than making it ! If you have less than 3 components or less to satisfied your design project ? Then it is much better . Anywhere I respect and salute your effort Idea/knowledge Sharing . Thanks , very good job done .

[@bengalmirror]

Great work

[@gourabkundu4988]

You are my real teacher You are great sir

[@vobinhthu5299]

This project is very good!

[@tokitahmid6641]

what software you use for circuit diagram ?

[@ajaybnl]

Firstly Your CT Coil is not set for Current Mode (Put 10R or 1R at CT's Both Pins). Secondly, Your 555 Timer's Capacitors will charge after some time by using any AC Load, Hence you will keep yourself clicking the reset button after now & while (Under Low Load). Sadly, bad designs, not tested. Please make usable circuits which are tested by professionals (see Internet). Cheers.

[@TheJavaSync]

Link pls ;)

[@michaelobi5347]

Thank you for sharing your knowledge to us. What is the output of the current transformer ct used in this circuit

[@rafaelcesarriveros8921]

Very good, dynamic presentation congratulations, what is the name of the virtual presenter of electronic circuits, thanks

[@hitechelectricalvijapur7791]

Good...👍👍👍

[@BabuLal-lh3wq]

Veri nice video. Please upload the hindi version video.

[@wolfman-s2c]

Hello Thank you How much voltage and amperage does it support?

[@SandipDas-ct3dl]

Can this circuit also auto cut if ac line is short circuit that means phase and neutral is connected...?

[@SandipDas-ct3dl]

#KiyanisLab #CircuitBreaker...##..hello...plz reply...

[@SandipDas-ct3dl]

#kiyanis Lab# aap reply kuy nahi karte...

[@gourabkundu4988]

Very very nice video Thank you so much Sir

[@mayoortechinnovations]

Please can this design also work as a short circuit protection too...?? 🤷

[@sajitr1184]

Can it be used as over load protection

[@AmanSingh-qt9ss]

I am not understanding that are you takeing 12v as output or Ac

[@mitiduragenimal9261]

Good..seee

[@tokitahmid6641]

How many maximum voltage we can use ? ampere ?

[@mubinahmad6581]

Sir i can use 30 amp relay replacement of this relay

[@farazpsc]

Current transformer k volt 12v hy ya 6v

[@sahilchine7976]

We can use ct coil replacing transformer

[@SammieOfficial]

Great

[@belkacemcherif9805]

Is bretter to Write a List for components.

[@604smit]

What is the program you make those nice layouts with.? (With the blue background)

[@anupkundu8395]

Sir Jo CT aap ne apply kiya us ke bare mai bato

[@vjcreat-tech6038]

Jo ct apne use kiya, ke bare m bataye?

[@zafar8mughal197]

Nice

[@fast3010]

The name of the software used to make the video

[@ramukumar2875]

Sir why you use here a current transformer and this current transformer of what value

[@DrAabed]

Current transformer To 12 V for A Relay

[@allhelpyou1232]

Tda7388 ic amplifier making sir please🙏

[@kv27br96s10]

Circuito muito bem feito

[@channelnyalelaki9319]

Flame Failure gas ignition Circuit Breaker please...

[@raajandear7284]

भाई हिंदी में ही बोल लिया करो कुछ हमारे जैसे अनपढ़ भी है दुनिया में

[@allhelpyou1232]

Howe to make wireless mic 🎤

[@marksilva309]

I have several issues with this video. No explanation of the circuit theory is given, nor any of the test procedure. Current transformer not described in detail. I cannot read the Chinese datasheet. What is the turns ratio and core material? Should there not be a burden resistor on the output? If you designed this circuit you should explain it. Why use a 555 timer instead of an op-amp or comparator? Watching you solder may be interesting for some, but does not impart useful information. Also, why not use a formal schematic? They are easier to read, IMHO Mark S.

[@KiyanisLab]

sorry for that bro soon i will make explanation videos of my project

[@allhelpyou1232]

Howe to make wireless mic🎤

[@dilshadjafar6164]

Sir Hindi LENGWEJ me Boliye na please😫🙏🙏💓

[@anupkundu8395]

Woh ct ke bare mai bilkul pata nahi lag raha hai

[@blackpanther1662]

Better buy a ready made one it’s cheaper

[@anupkundu8395]

Plse maherbani kar ke reply degiye!

[@mahtabalam7833]

Clapping switch circuit

[@KiyanisLab]

ok

[@fast3010]

electronic circuit diagram

[@faisalkhanafridi2150]

This circuit Only 12v supporters i have 48v

[@anupkundu8395]

Agar reply karenge 2 days bad aapko reply kar denge

[@anupkundu8395]

I am a subscriber of your channel plse help me to learn some knowledge

[@АльбертОганесян-о1м]

Так Я Вообще Не Понял-Что За Хуйня. Хот Кто Обяснит?.👈😁😁😁

[@SandipDas-ct3dl]

fake video....time waste...wrong circuit diagram...

[@tokitahmid6641]

why bro ? it is real ? you can also contract me .

[@dnaelectronics8794]

Fake

[@tokitahmid6641]

why bro ? it is real ? you can also contract me .

[@mayoortechinnovations]

@@tokitahmid6641 please can this circuit also work as short circuit protection...?

[@tokitahmid6641]

@@mayoortechinnovations I think this project should work if it is made like a diagram in the right way. I made a DC 12 volt project. CT was not used there. It was working. And this project uses AC volts and CT here. You can try.

[@mayoortechinnovations]

@@tokitahmid6641 ok thanks I will try

[@homemade1119]

It's real, I was tested and its working perfectly

[@amirmayo7102]

Fake