KSGER C210b Soldering Station Tear Down & Review

KSGER C210b Soldering Station Tear Down & Review
www.pcbway.com/ Get 5 boards in about a week for $22!
www.aliexpress.com/item/32568...
*************************************************************************
Please help support this channel at NO COST TO YOU. If you shop on *Amazon, please use this link: amzn.to/3706t6c *
*I will get a small commission and it costs you nothing. *
*************************************************************************
Learnelectronics Merchandise:
Yes!! I now have merch: teespring.com/stores/learnele... Electronics themed T-Shirts!
----------------------------------------------------------------------------------------------------------------
HEY YOU ABOUT TO POST SOMETHING STUPID:
Yes, I know my hands are large/fat. It's because of a heart condition I suffer from called Congestive Heart Failure. Here's a link to some information about CHF: cle.clinic/2TdS2Ux
One of the symptoms is that it causes fluid retention, mostly in the hands, feet/ankles, and face..
--------------------------------------------------------------------------------------------------------------------
Amazon Store:
If you are shopping for electronic components, test gear or consumables please consider visiting my Amazon shop @ amazon.com/shop/learnelectronics
Please check out www.patreon.com/learnelectronics and pledge a dollar if you can. It will go a long way to keeping the channel alive. It costs a bit of money to buy all the items and produce these videos. Your help is appreciated.
---------------------------------------------------------------------------------------------------------------------
Donation:
Or....if you'd like to send a one-time donation you can use this link: paypal.me/learnelectronics
---------------------------------------------------------------------------------------------------------------------
Gear I use:
DMM: Owon B33+ - amzn.to/3qQgH20
Power Supply: Matrix 3206 - amzn.to/37C0fL9
Portable O'scope: YEAPOOK ADS1013D - amzn.to/2ZG4G3x
Bench O'Scope:Hantek DSO2D15
- amzn.to/3ir307N
Soldering Station - KSGER T12 - amzn.to/2NuNdby
Multimeter leads: Probemaster - amzn.to/2ZJ0BLK

[@amrishhirani6096]

Nice micro soldierg station Thanks

[@Hootz99]

SLP = Solder Like a Pro 😎

[@emmettturner9452]

10:44 “One moment please.” Channeling Big Clive there, I see? ;)

[@tigrafrog]

Did I miss something or Paul did not check grounding on cartridge itself? Lots of rumors that those cartridges (original AND "generics") have very short lifespan, less than T12s.

[@mimeanalytics4331]

You obviously worked with T12 too, how would you compare that to t210?

[@ketanmakol4571]

It shows H-E what to do

[@MrYevelnad]

Seems like its a downgrade from their previous stations. IDK if the jbc tip is a pro or a con because they are way expensive than the t12. And its very hard to get the original one in different regions.

[@brianmiller6320]

I am still using a 1970s Weller TCP2, am I out of date? Is it valuable?

[@ivankirola2707]

Don't even think about replacing it.

[@davadoff]

You didn’t measure tip to earth potential and check if the tip is earthed (specs: 2 Ohm,

[@rtwodtwo9338]

peace !

[@bblod4896]

Does the tip have the heater element built in or does the tip just fit over a heater element? I think the web site answered the question. Have a great weekend Paul. ☮️

[@andrewsawesome]

The tips for these stations have the heating element bulit in

[@davadoff]

@@andrewsawesomenot Chinese tips. I’ve seen some that look like the tips are press fit over the top. Look at the join between tip and the main shaft of the cartridge. It’s not one piece. With original JBC, the outside is one continuous surface.

[@bblod4896]

Was that soldier station "sponge worthy"? That's your only hint.... ☮️

[@learnelectronics]

I wouldn't spare a square

[@bblod4896]

@@learnelectronics LOL

[@LawpickingLocksmith]

You could teach Louis Rossmann how to skin a cat?

[@John_Smith__]

SLP = SLEEP mode.

[@mr.q3216]

I recently bought AIRMX 2.9" LED Digital Soldering Iron Station Kit , much cheaper.

[@hmjeon8609]

c210 tip is so responsive that I can not return to the t12 soldering station again.

[@razpootis5802]

I'm not a big fan of manufacturers using epoxy in their devices. Such a hassle to disassemble for repairs or salvaging.

[@davadoff]

💀 That station is dangerous 💀 Tiny air gap & one layer of insulation by the PSU screw terminals and exposed pads of the iron connector. Live wire could fall out or have loose strand and make the iron connector live. In 240v land it is very spicy indeed. Regardless, such a small gap and one layer insulation is not okay. Wires need to be sleeved, soldered to PSU and silastic’d in place. Or redesign the product.

[@emmettturner9452]

“Leed free?!” Uh…

[@Legend813a]

super long play

[@learnelectronics]

I'm old enough to remember those

[@MrDinakdakan]

Why do they include useless tips