Kukirin G3 Pro…. Found bearing destroyed during Rear EXA 291R Installation.

  Рет қаралды 477

CanaScot Scoot

CanaScot Scoot

Күн бұрын

Пікірлер: 16
@El_Scootisto
@El_Scootisto Ай бұрын
Might I ask please, the specs on those little bearings and where you found that pack of replacements?
@scottishcanna-dian7965
@scottishcanna-dian7965 Ай бұрын
@@El_Scootisto The correct size is 63802-2RS Deep Groove Bearings 15x24x7mm …… link below a.co/d/hq3Awmp Hope they come out ok , I had a bit of trouble getting one out …. Thanks for the interest … Good luck 😊
@El_Scootisto
@El_Scootisto Ай бұрын
@@scottishcanna-dian7965 Thanks for the help! I have the Roadrunner, and yesterday had to loosen the swing arm bolts because they were too tight from factory. I became concerned for the bearings, and your video was just what I needed to see! Thanks for posting helpful material.
@scottishcanna-dian7965
@scottishcanna-dian7965 Ай бұрын
@@El_Scootisto no problem, I think the bearings are possibly damaged by over tightening those nuts at the swing arms I had one at the front & one at the back completely destroyed & came out in bits . I believe they were over tightened at the factory. I watched a video on a Vsett that mentioned 30lbs torque at each nut but I just make sure it feels tight enough without crushing the bearings .
@scottishcanna-dian7965
@scottishcanna-dian7965 Ай бұрын
I wish I bought the RS5 Max , I’m gradually upgrading mine .. the Exa 291R suspension is great ..feels like a new scooter. 🛴 💨
@El_Scootisto
@El_Scootisto Ай бұрын
@@scottishcanna-dian7965 The Max is the one I have. It's got the 6.5" motors so I'm about to put 11" PMT's on it. I've got a 150mm EXA shock on the way from AliExpress, but I don't want to raise the front end by putting a 125 on there. Also, I'm going to have to put different fenders on.
@garretcallan
@garretcallan Ай бұрын
Can I ask you where you got this suspension from?
@scottishcanna-dian7965
@scottishcanna-dian7965 Ай бұрын
@@garretcallan AliExpress 😃
@garretcallan
@garretcallan Ай бұрын
​@@scottishcanna-dian7965tanks
@karolmichalak7381
@karolmichalak7381 Ай бұрын
how many mm is exa 291r?
@scottishcanna-dian7965
@scottishcanna-dian7965 Ай бұрын
@@karolmichalak7381 125mm Front / 150mm Rear
@karolmichalak7381
@karolmichalak7381 Ай бұрын
@@scottishcanna-dian7965 thank you 🦾😎
@joehiatt1992
@joehiatt1992 7 күн бұрын
@@scottishcanna-dian7965 I see them on the site,what poundage did u get ?
@scottishcanna-dian7965
@scottishcanna-dian7965 7 күн бұрын
@@joehiatt1992 2000lbs
@joehiatt1992
@joehiatt1992 3 күн бұрын
@@scottishcanna-dian7965 Just ordered the shocks & another charger from Aliexpress, my Gallop arrives tomorrow
Kugoo Kirin G3 Pro плюсы и минусы от владельца
19:03
Saved from Deadly Ball Bearing Shrapnel - Bulletproof Window Did Its Job!
9:37
Hydraulic Press Channel
Рет қаралды 83 М.
哈莉奎因怎么变骷髅了#小丑 #shorts
00:19
好人小丑
Рет қаралды 55 МЛН
5 Reasons Not To Buy The Kukirin G3 Pro + Test Ride
35:04
Sir Kay
Рет қаралды 6 М.
Ledge X1 | EXA Form 291R Coil Shock | Initial/Realtime/Comparison
18:06
Плавники для надувных SUP досок
41:07
SUP Travel Kolomna
Рет қаралды 47 М.
HYDRAULIC PRESS KNIFE VS CARBON FIBER AND TITANIUM
8:07
Crazy Hydraulic Press
Рет қаралды 12 М.
Unboxing Rear Shock Kind Shock (KS) 291 R (Rebound)
9:34
Andi a lone
Рет қаралды 1,5 М.
Tricks and amazing ideas in metal turning
9:39
بيت الهيدروليك & Hydraulic house
Рет қаралды 10 М.