That is a simple and elegant solution. A product of intelligence and problem-solving experience. Good job!
@ThePapa19474 жыл бұрын
Paul thank you very much for those very kind and generous words. Gary
@ThePapa1947 Жыл бұрын
Great! Happy this has helped. Gary
@WoodsleeSummercraftwoodturning4 жыл бұрын
I just bought a laguna 18-36 I’ll give this a shot Thanks Rob
@ThePapa19474 жыл бұрын
Thank you I use mine a lot. You will enjoy the 18-36 it is a fine lathe. Thanks for watching. Gary
@live2ride8835 жыл бұрын
Sometimes the simplest answers are the hardest to see, and the best solution. Great idea, thanks for sharing.
@ThePapa19475 жыл бұрын
Thank you. I use it all the time. Gary
@chuckkubin25573 жыл бұрын
Very clever!!!!! Cheap, easy, smart, and adaptable to any lathe with a similar position lock.
@ThePapa19473 жыл бұрын
Thank you Chuck. I really find it useful to have a locking spindle for many reasons. Thanks for watching, Gary
@ScenicCityWoodturning2 жыл бұрын
Oh that's a great idea, Gary. I've been using the indexing knobs to lock it, but I don't like using those since that's really not what they're for. I'm afraid it will eventually damage those holes. Thanks for the tip. 👍
@ThePapa19472 жыл бұрын
Thanks Mike. For sure do not use the indexing pin. I did not like holding the red button in so came up with this. I even got a hold of Laguna and ask why they could not have a locking system. My fix is very simple for sure.
@ScenicCityWoodturning2 жыл бұрын
I already have magnets on the way 😁👍🏻
@leesleeper8488 Жыл бұрын
Great idea - I will make one for my Revo 24/36 tomorrow. Thanks.
@ThePapa1947 Жыл бұрын
Thank you and I use mine almost every time I use the lathe. Thanks for watching, Gary
@RHumphrey5 жыл бұрын
Nice final fix! Off topic...that's a really good looking chunk of wood you mounted on that worm screw....🙂
@ThePapa19475 жыл бұрын
Well Rod I knew you would notice. Let me tell you I was in awe during the whole turning of that piece. Well I just put finish on the bottom a hour ago. And the bottom looked delicious. This has to be the prettiest piece of wood I have ever done. It felt like a gift to be able to expose the grain inside. Another chunk that I just wasn't sure about. I can have it ready for Friday and I want to. I had something else read to load but it can wait. Thanks for watching brother. Gary
@larryhurwitz92062 жыл бұрын
I have the same lathe and I agree the way the spindle lock works makes no sense to me. Thank you for the quick fix
@ThePapa19472 жыл бұрын
Thank you Larry. That really bugged me when I discovered that it did not actually have a way to lock it. I did not want to drill holes and had a lot of those magnets. Thanks for watching, Gary
@georgemccombs50705 жыл бұрын
I have a Laguna 1824 same problem. Thanks for the idea
@ThePapa19475 жыл бұрын
You are very welcome. Gary
@PhilAndersonShadyAcresWoodshop5 жыл бұрын
Brilliant, Gary! I hope this video gets a million views, it deserves it. Something so simple you would think Laguna would have included it. You should see if you can send them the link. They might feature the video on their site. Great job thinking outside the box! Phil
@ThePapa19475 жыл бұрын
Thanks Phil. Maybe I will send them the link. I am taking pictures of my next WEIRD turning right this minute. The cat wants to be in the picture so I had to move my photo studio. Thanks for your comments as always. I just heard back from Laguna. He said Well that was a simple solution. Gary
@WoodenItBeNice2 жыл бұрын
Brilliant solution to your problem. Love Mark 2 with the extra safety feature. Hwyl, Huw
@ThePapa19472 жыл бұрын
Thank you Huw, I thought it was silly not to have a spindle lock other than holding the button in. So I fixed that. I have had people say having a locking spindle is not necessary. But I find it very handy. Hwyl, Gary
@clintmyrick41285 жыл бұрын
Thanks Gary. I have the exact lathe and this has troubled me too. I will adopt the same fix. You've mentioned before you are in Oregon; I'm in Eugene.
@ThePapa19475 жыл бұрын
You are welcome Clint. I am in Garden Home which is next to Beaverton. Did you have any trouble with the banjo locking down? What ever they painted the hidden shaft with is to slick. I scuffed it up with 120 grit and that fixed the problem. Gary
@josephwise4855 жыл бұрын
Nice fix. You have to love what you can use rare earth magnets for.
@ThePapa19475 жыл бұрын
Thank you. Yes they are very handy. I have also used it to keep the 4 jaw chuck handy. You can just stick the end of the handle to it. Makes it easy to grab. Gary
@anitabier21142 жыл бұрын
Thank you for the video! Helps immensely!
@ThePapa19472 жыл бұрын
Thank you Anita, happy it was helpful. Gary
@snturner103 жыл бұрын
Nice job. I will be making one of these for my lathe. Thank you for posting this.
@ThePapa19473 жыл бұрын
Thank you Scott I would have a hard time getting by without it. Some people claim you do not need a spindle lock but it sure helps getting a chuck off. Or when putting a blank on a worm screw. But I am sure you know all of that. I considered getting the 2436 as it would not have taken up anymore foot print. It is a dandy! Thanks for watching, Gary
@sapphodesigns23774 жыл бұрын
That's so simple its brilliant..I will be making one of these for mine..thanks for sharing
@ThePapa19474 жыл бұрын
Thank you and I am happy you like it. I find it very hard to get by without one. Gary
@uncletim98745 жыл бұрын
Ingenious and clever to boot. Turn the end into a knob and paint it red, it will look even better.
@ThePapa19475 жыл бұрын
Excellent idea I may have to do that. Gary
@leesleeper8488 Жыл бұрын
A great solution - thanks for the tip. I just made mine, and it works great.
@ThePapa1947 Жыл бұрын
Great Happy this has helped. Gary
@davidaion5 жыл бұрын
Thanks. Appreciate the help. I'm going to do this today.
@ThePapa19475 жыл бұрын
You are very welcome it is a fun easy and great project and you will be happy you made it.. Gary
@BillMSmith5 жыл бұрын
Very effective and efficient, my favorite combination. I'll have to modify that idea for my Jet.
@ThePapa19475 жыл бұрын
Glad you can use the method. Thanks for watching and commenting. Gary
@markr.15844 жыл бұрын
Great idea
@ThePapa19474 жыл бұрын
Thank you Mark I a glad you liked it. I use it all the time. Thanks for watching. Gary
@billy194615 жыл бұрын
Some of the best inventions are the simplest.
@ThePapa19475 жыл бұрын
Thank you Billy and I like simple. Although I tend to over complicate most things. Gary
@TheMessyStudio5 жыл бұрын
Great quick fix, Gary! I might be able to use something like this for my Mustard Monster. Thanks! Billy
@ThePapa19475 жыл бұрын
Thanks Billy, I thought they had spindle locks? Hope you have a Happy New Year Gary
@TheMessyStudio5 жыл бұрын
@@ThePapa1947 The newer ones do. I got mine in 2005 or 2006. Billy
@fergusrb Жыл бұрын
Thanks , just got a laguna 18/36 and was wondering how to hold the button in. Now I just need some magnets.
@ThePapa1947 Жыл бұрын
Thank you Bruce and I use mine all the time and it is just second nature to use. Thanks for watching, Gary
@fergusrb Жыл бұрын
@@ThePapa1947 also sent your video to my son who also has a 18/36 Laguna .
@carolriley5695 жыл бұрын
Great solution!
@ThePapa19475 жыл бұрын
Thank you Carol! Gary
@AlVitale-h3i10 ай бұрын
Thank You, Gary. Can you tell me where you bought the magnets AND their strength? I purchased several different magnets but none of them are strong enough to keep the button in on my 18/36. I asked Laguna what pressure the button needs to be depressed. Unfortunately they did not have an answer. Thanks again, Al.
@ThePapa194710 ай бұрын
Hi Al, This is the size I use. www.ebay.com/itm/374530091966 You may be able to find them on Amazon. We had a supplier at work where we got them. We used them for tooling that we built. Hope this helps, Gary
@calmwoodcreations37095 жыл бұрын
Excellent! Thank you so much. 😁👍
@ThePapa19475 жыл бұрын
You are very welcome
@davidaion5 жыл бұрын
BRILLIANT
@ThePapa19475 жыл бұрын
David thank you very much. I appreciate your comment. Thanks for watching. Gary
@MAXWOODTURNING Жыл бұрын
What magnet did you use? Mine seem not strong enough to hold it :-(
@ThePapa1947 Жыл бұрын
I used the Rare Earth magnets. You can hardly get two of those apart when stuck together. Funny I just got a pack from Amazon. These are very thin and I will use them on a laser machine to hold thin pieces down. For the spindle lock I would use 1/2X1/2" magnets. Best of luck, Gary
@MAXWOODTURNING Жыл бұрын
@@ThePapa1947 yeah i try with a 12mm x 3mm and its not strong enough to hold the spring, maybe is just too small. Thanks
@MAXWOODTURNING Жыл бұрын
Finally i design it with bigger one ;) kzbin.info/www/bejne/gqWkq5drorWGjpI
@ThePapa1947 Жыл бұрын
@@MAXWOODTURNING looks great!
@johnhorsfall32815 жыл бұрын
Good Idea I was having this trouble but now I am not Thank you
@ThePapa19475 жыл бұрын
You are welcome. I did not feel like drilling holes in a casting. You could end up on a grain line of the metal and cause a crack. Metal has grain based on how it hardens after cast. The magnets solved that issue. Thanks for watching and commenting. Gary
@davidaion5 жыл бұрын
Can you share the specs on the magnets? Where did you get them and what size?
@ThePapa19475 жыл бұрын
David they are rare earth magnets and the ones I used are 1/2 x 1/2 inch and they are something we used at work.Pretty sure they got them at a local hardware store or one of out tool suppliers. I have been retired about 7 years or I would ask. But I know that Home Depot carries rare earth magnets. Maybe not 1/2 thick but you could stack them to get what ever you need.Harbor Freight also has some of the rare earth magnets. I have used them to get the chuck key handy as well. If you check my video on using a Digital angle finder for your grinder you will see how I use the magnets in a zip bag to collect the grindings coming off your wheels. Thanks again, Gary
@jeantanguy55353 жыл бұрын
Bravo i have à 2436 home Laguna see tour video
@ThePapa19473 жыл бұрын
Very nice!
@michaelglackin2420 Жыл бұрын
What harm to the lathe would leaving the lock in
@ThePapa1947 Жыл бұрын
None that know of. Most VFD's will shut down if they sense too heavy of a load. I know mine does as I have done it a couple of times. Same thing on my Bridgeport CNC.
@michaelglackin2420 Жыл бұрын
@@ThePapa1947 thanks for that good information 👍 love watching your videos
@ThePapa1947 Жыл бұрын
You are welcome and thank you!
@davidlipschitz64222 жыл бұрын
So smaht!
@ThePapa19472 жыл бұрын
Thank you David, a very hand addition for sure. Thanks for watching, Gary