How to Mix and Spray Rustoleum Paint for a Budget Paint Job

Looking for a budget paint job? In this video you'll learn how to mix and spray common Rustoleum paint for use on anything from car / truck frames and rims to overall paint jobs.
/ @lakesideautobody

[@mds6387]

Straight down to business with this video. Very easy to follow, and not complicated at all. Thank you very much for posting this video!

[@LakesideAutobody]

You're welcome MDS - glad you liked it :)

[@MrGiantstpss]

I agree. I don’t have the patience for stupid intros, watching those other clowns driving to the store to buy the products, and then taking 20 minutes to open the boxes.

[@reynaldovalle1773]

I painted a blue Chevy I had with blue Rust-Oleum came out beautiful. I find that to be the best paint for the price you can't complain...😁👍👍👍

[@johnyhefner]

The other videos out there often confuse me. These videos are straightforward and understandable. I know I can do this now.

[@LakesideAutobody]

Glad to hear it Johan - have a good weekend :)

[@ray8380]

what would happen if i spray clear coat after

[@LakesideAutobody]

@@ray8380 I've seen videos on that but have not tried it myself. I'll look into that a see if there is a clear that will be successful over oil based enamel without sanding it first.

[@ronnieyoung7510]

Should I use some of that Japanese dryer with acetone

[@autosalvage]

if u use 4 parts paint and 3 parts acetone and 2 caps full of catylist hardner it will hold up just like reg auto paint there is a lot of hotrods painted with it and last for years

[@overratedsrtchallenger]

Would it dry faster and come out less gummy?

[@autosalvage]

@@overratedsrtchallenger when u put the hardner in it it will dry quicker but u have to wait a few days before u drive it

[@tonimalveaux67]

Great tip

[@autosalvage]

@@tonimalveaux67 thanks

[@mrbigbuds1745]

Can I use moré harder?

[@scottberry5266]

I’ve been painting semi truck frames with rustoleum for years. I live in Michigan and this paint holds up better than the factory paint or anything else.

[@LakesideAutobody]

You're right. Rustoleum is oil based enamel and it's really pretty tough stuff :)

[@tim9lives]

Thanks for posting this. I just was looking for info on spraying a piece of equipment. But wow... I might even paint my 25 y/o truck now. Great instructional video. Thanks again!

[@LakesideAutobody]

You're welcome - Jerry

[@nmartin5551]

AWESOME video!! To the point, clear, no annoying talk and/or music. Thanks. I’m going to spray a car hauler, so it’s not going to be a work of art that has to look good, but I want it to look better!!

[@LakesideAutobody]

It will work fine for that :)

[@jojojeep1]

Not to mention, I’ve seen some beautiful, rust oleum paint jobs they color sand it and buff and it looks beautiful

[@peterandrego2331]

Very impressed. Most painting videos I couldn't finish watching because they had annoying music or made me nauseous (I think they had the camera strapped to their wrist as they sanded!) Even more impressed Jerry that you patiently reply to any questions! I've subscribed.

[@LakesideAutobody]

Thanks, ask as many ?'s as you want. Have a great weekend.

[@michaelmurray5505]

When he says wet and wetter does he meen different mixer or a gun setting?

[@tonybroussard377]

Majic it is! Can a very fine metal flake be added to Rust Oleum? If so, just on the last coat or on every coat?

[@gregpetty4185]

I’ve been painting with Rustoleum for decades. I prefer mineral spirits with a little hardener as acetone dries too fast. Color matching is always challenging.

[@LakesideAutobody]

Thanks for you input :)

[@luissantana3772]

What the ratio and what type hardener did you use

[@perrikdesrocers4507]

Any paint hardener

[@Ksshortyb]

RUSTOLIUM IS OIL BASED ENAMEL. YOU REALLY DONT WANT TO MIX ENAMEL WITH PAINT THINNER OR MINERAL SPIRITS. ACETONE IS BEST CUT. AND XY. ENAMEL IS GOOD FOR AUTO BODY, MOTORCYCLES ECT, BECAUSE WHEN IT CURES IT CURES HARD LIKE A SHELL. EPOXY IS TO SOFT. LAQUER IS GOOD FOR AUTO TOO. I PAINT ALL MY CROTCH ROCKETS WITH ENAMEL. MY ZX6R I DID A BASE COAT METALIC SILVER AND THE THINNED OUT A BURNT ORANGE WITH CLEAR COAT SO IT WAS TRANSPARENT, THEN TOPPED IT WITH HARD AUTO CLEAR. BUFFED IT. YOU WOULD NEVER BE ABLE TO TELL THE DIFFERENCE BETWEEN THIS PAINT JOB I DID AND A AUTO CANDY COAT. GOOD SHIT

[@tossedsalad5532]

Great job to show a cheap paint job. I have owned a body shop for 35 years and painted with Rust-Oleum acetone and hardener then clear-coated After applying the base coat completely wet sanded then two coats of clearcoat. There was definite areas that required some wet sanding and buffing wear orange peel occurred because of my spray overlay and hand speed with the gun. I'm not going to blame it on the product in other instances orange peel did not happen. I've had orange peel with every type of automotive paint used and I will repeat did usually never came down to the product but hand control of the gun. You're definitely an Old Skool Pro who did a great video for anyone wanting to put some sweat equity and cheaper finances into making a vehicle look better

[@LakesideAutobody]

Thanks for the comment - I enjoyed reading it. I agree with you on getting orange peel with any paint. By the way, what did you use for clear over rustoleum? Thanks again - Jerry

[@skkfor]

Great vid. I painted my beater Jeep with your direction and it turned out really nice. Problem is, now it's not a "beater" anymore. Now, I'm actually picky about where I park it! I'll just have to find another beater Jeep toy... Many thanks for the vid!

[@LakesideAutobody]

That's really good to hear. Yep the fun is actually looking for them. Jerry

[@tashatorrid]

Good job. I did an old car of mine using 50/50 Rustoleum to mineral spirits and it came out really good. Nice cheap way to pretty up a rat.

[@LakesideAutobody]

Thanks - Jerry

[@ronnieyoung7510]

Did you stand father away from the car with the 50/50 ratio so it won't run

[@limabravo6065]

Rustoleum is an alkyd enamel and it’ll act like any other enamel when thinned, and if you add an enamel hardener it will catalyze like any other 2k paint. Just thinning it will make it dry faster but it won’t last and it will come off with chemicals like acetone.

[@DesertJeff]

Thank you for the efforts and putting your video together. I know now how to mix my Rust-Oleum paint. Sometimes we just need showed something once or twice so we know how to do it ourselves. Again thank you for the video.

[@LakesideAutobody]

You're welcome

[@davidweum9334]

I agree, but im a virgin truck painter. David Alberta

[@vprince9907]

@@davidweum9334 you can do bro just take your time with it an you'll do fine.. got any pics of the job ?

[@vprince9907]

I gotta start out with a 1 to 1

[@ronnieyoung7510]

What ratio did you use could you answer me please appreciate it

[@claybirdnone6804]

Hi Jerry, I finally painted one of my old trucks with Rustoleum, '78 Chevy. It turned out pretty good. It's Safety Blue. It was a pretty beat up old truck, I had a ton of bodywork to do. I missed a couple dings too, Lol! Thank you for your awesome videos!!

[@LakesideAutobody]

I love hearing that. Who cares if there are a few mistakes - it happens to everyone. It's the guy/gal that can work with or repair their mistakes that succeeds. With every job you get better :)

[@ronaldlewis4032]

I will paint my core support and inner fenders with this .They offer a catalyst for hardener that I use too . Thanks for the. Always a big help.

[@LakesideAutobody]

Glad to hear it - it is great paint once it dries - pretty durable.

[@igortretsnom]

I painted a bus using Rustoleum. Bought white and tinted it tan. Worked great!

[@LakesideAutobody]

That's good to hear - it is actually pretty darn good paint for the price.

[@anthonymaniz1933]

Did you use straight or a ruducer

[@igortretsnom]

@@anthonymaniz1933 reduced enough to replicate automotive paint.

[@markbrown1609]

This guy at Lakeside auto has great videos for the man that wants to get out of the house and DIY.

[@LakesideAutobody]

Thanks Mark - glad you like them :)

[@lcar9871]

Another great video! I have not tried Acetone but did a lot with Rustoleum and Xylene and it worked great on new steel (angle, channel, square tubing etc). Back when the big 8 & 10 foot dish antennas were sprouting everywhere (70s & 80s?) I was building antenna mounts for them, along with other metal fab work. Rustoleum cut with Xylene was my go-to paint. Looked nice and, for reasons I can't explain, seemed more durable than when I cut it with paint thinner. Larry

[@LakesideAutobody]

Rustoleum is actually pretty good paint for rust protection as it is very durable for sure. Thanks for the comment.

[@garylangley4502]

When I had an appliance business, I would use Naptha to thin an enamel paint, and I used a viscosity cup to determine the mix. I forget what the time was for the cup, but it gave great results.

[@LakesideAutobody]

I've heard of the viscosity cup and really need to get one. Sometimes paint is way to thick the way they say to mix it i.e. paintforcars.com acrylic enamel single stage, rustoleum, etc.

[@garylangley4502]

@@LakesideAutobody I'll try the website, and yes, the instructions can make it way too thick. I often see instructions say not to thin more than 10%. It would still be thick as syrup. Too thick for even brushing it on some iron railing.

[@garylangley4502]

@@LakesideAutobody By the way, are you in Lakeside California?

[@michaeldeignan7922]

acetone evaporates faster then naptha :quick dry between coats

[@topcat5988]

This is the best channel to have ever come across!

[@LakesideAutobody]

Thanks Topcat - I appreciate your kind words :)

[@makkra7565]

Very usefull content on a budget

[@PimpedPrevia]

Great video !! thats the way to do it. You can also add some medium hardener (0.8 part) Will be easier to cut n buff

[@LakesideAutobody]

I agree. Works nice with the hardener. You can mix it a little thicker I think too - it does run easy.

[@rigoslittleshop9430]

Which hardner can I use? Clear coat activator would work?

[@PimpedPrevia]

@@rigoslittleshop9430 usually using universal acrylic eurethane hardener. Medium speed for clearcoats

[@mobilehomelife4028]

I am getting ready to paint my beetle fenders, this is really helpful!

[@LakesideAutobody]

Glad to hear it MHL - feel free to ask ?s as you go :)

[@artists1015]

I used the same method for metal doors on a church, lasted a few years but faded badly within the second year! If you want to slow down the fading, you must keep it waxed at all times!

[@LakesideAutobody]

Thanks for the tip :)

[@danwingo7512]

It also helps to use a hardener and Japan Drier.

[@rjwhipple8896]

Did a lot of panels on my cars like this and years later they’re still holding up strong. I’m in the middle of painting my old neon grey right now like this

[@LakesideAutobody]

Thanks for your input RJ :)

[@ivor7407]

Using acetone as a thinner will take days to dry. Med dry reducer will give it a higher gloss finish. Keep your spray gun 6 inches from whatever your painting is the key.

[@LakesideAutobody]

Are you talking about this type of reducer - Majic 8-0750-3 Enamel Reducer or are you saying you are using urethane reducer?

[@57mailman]

I’m planning to repaint my ‘29 model A with a Rust oleum paint. I like your technique.

[@LakesideAutobody]

Majic enamel hardener my help with that project. I think if you do a few test panels - like paint a few old coffee cans first, it may help you decide what setting, mix ratios, hardeners work best for you and the outside temperature you're working with :)

[@oleskool6259]

Great just the video I’m looking for because I got off track and was overdoing it. This will get me back in the ballpark.

[@LakesideAutobody]

Thank OS - glad you liked it :)

[@johnhenke6475]

I custom painted my motorcycle with Rustoleum, sealed it with Minwax Helmsman clear coat and it came out beautiful.

[@LakesideAutobody]

Thanks for that comment. A lot of folks have been asking about a clear coat for it. Have a great weekend :)

[@bob14219]

I tried the same thing on a f-250 - after a few months in the sun the paint checked like alligator skin - the Helmsman caused that - never happens with just Rustoleum.

[@ronnieyoung7510]

Where did you buy the clear coat at I appreciate for the answer to me I need to start an old car I'd like to clear coat it thank you

[@tossedsalad5532]

In our shop we tried 3 or 4 different clear over the rustoleum. Endura clear coat, PPG clear coat, industrial high performance clear coat, and even Rust-Oleum clear coat. All of them worked fine we never had an issue with the Rust-Oleum being clear-coated when we left enough time for the and elapsed time between clear coat. We did have occasion when we did not leave enough time and one or two areas created little bubblrs. I agree with you that proper preparation wipe down and pure common sense make a better job. Every instance when we had issues related to Rushing of speed because somebody wanted economical job. Moral of the story take a little extra time letting things set up pays dividends and not having to redo the job and spend that extra time and materials to redo it. A good quality masking tape and sandpaper make a huge difference also on an effective job. As for having Hi-Tech paint booths. In the 70s custom paint jobs we're done on dirt floors that were wedded down not a downdraft heated paint booth. Keep up the good videos you're a true old school pro

[@LakesideAutobody]

Absolutely! My dad worked at a place called JR's Custom Paint in Utica, MI - they did vets and custom vans with cool pictures of mermaids and all kinds of stuff. They were the most beautiful paint jobs I've ever seen and they were done right there in the shop (no booth) - Have a great week - Jerry

[@gilbertoferreira7964]

Great job l like the way it looks

[@pospc2]

I used rustolium paint on a 2g dsm. Turned out nice after sanding and polishing.

[@vprince9907]

So after you applied the number of coats desired and allowed to fully dry...what did you use to then sand it to which you finished that up by polishing the rustoleum?? What compound did you go with in respect to polishing end product???

[@kuro0198]

@@vprince9907 when removing the orange peel effect in the paint wet sand with a fine grit sandpaper. Anywhere from 1500-2000+. Once you achieve a dull uniform finish use a two step paint compound and polish application. I have used meguiars m105 and m205 with an polisher and the results have been excellent. I hope this helps

[@pierrewellington9662]

Thanks for Answering just trying to figure out the paint and body work just for myself thanks again.

[@LakesideAutobody]

You're welcome - any time :)

[@joeyhill3698]

I have an old vintage Mac Tool chest that I've been restoring, and this would be an excellent paint choice!

[@LakesideAutobody]

Absolutely. The use of a hardener will make the paint dry faster and more durable too. www.amazon.com/Valspar-4625-Enamel-Hardener-oz/dp/B000LNY1MY/ref=cm_cr_arp_d_product_top?ie=UTF8

[@PatriceRobert20]

It looks amazing 😮

[@LakesideAutobody]

Thanks Patrice - have a good weekend my friend :)

[@waynec369]

Throw 1 part Majik hardener in there while yer at it. It's a little much according to directions, but sure does make a durable paint.

[@LakesideAutobody]

You're right Wayne - thanks for the comment and have a good weekend :)

[@jonathanolsen7254]

Big thanks going to do that on my trailer..

[@LakesideAutobody]

You're welcome JO :)

[@AB-C1]

Excellent video again, thanks from London England 👍😎🏴󠁧󠁢󠁥󠁮󠁧󠁿

[@LakesideAutobody]

You're welcome A BC. How's living in London England?

[@FixerMerlin]

Great job! You make it look so easy!

[@DaddyyCrab]

Using “rustoleum” makes sense, to beat back rust. I don’t know much about paint, but it seems it’d be more durable. Ty. You have very informative videos.

[@LakesideAutobody]

Thanks Daddy Crab - I appreciate the support :)

[@DaddyyCrab]

@@LakesideAutobody you are welcome sir. Years of experience you have. Awesome.

[@kingdommusic5456]

1 oz catalyst or japan drier should be mixed in to the paint and acetone mixture because rustoleum takes a week to fully dry without throughly

[@LakesideAutobody]

Absolutely agree - it works a lot better w/ hardener

[@myoneblackfriend3151]

Less than two minutes in and I am already smiling.

[@LakesideAutobody]

That's good..... I hope 👍😊

[@brianjohnson4186]

If u let it cure for 2 to 3 days you can wet sand and spray auto clear over the top

[@tommybomber]

Thank you for the tip!

[@donaldappelhof2059]

I wonder how it would hold up?

[@charliegilliland9216]

Glad I discovered this video! I have a '94 Chevy 1500 W/T with what I call 'Snakeskin Syndrome'. I peeled off the loose paint and sanded off the crappy factory primer and going Rust-Oleum all the way. I'm going to try my luck with an HVLP airless paint sprayer I got at Harbor Freight. Thanks for the tips on how to mix the paint, it's going to be very helpful to me.

[@LakesideAutobody]

Let me know how it goes. This enamel hardener may help you out a bit too - it'll dry faster, shine real nice, and be a bit more durable - www.amazon.com/Valspar-4625-Enamel-Hardener-oz/product-reviews/B000LNY1MY

[@charliegilliland9216]

@@LakesideAutobody thanks for the tip! I'll definitely look into that as I've had previous experience with hardners in paint and agree that the results would be better.

[@ronnieyoung7510]

@@LakesideAutobody I don't want to keep bugging you can you send me the paint ratio again I appreciate it

[@LakesideAutobody]

@@ronnieyoung7510 No problem. You'll mix 4 parts of paint to 1 part of hardener then thin it with right around 2-3 parts acetone or even mineral spirits. Here's a video on mixing paint that may help if you have trouble with ratios - kzbin.info/www/bejne/mabEaYxtnb2tl80 Keep asking ?s - no worries - Jerry

[@ronnieyoung7510]

@@LakesideAutobody it's not a problem can you send me the number on the hard enough at tractor supply you get

[@dukeallen432]

Will use this info. No more rattle cans. Thank you.

[@LakesideAutobody]

One thing to remember is when it's cold this paint likes to run so be careful. Use light coats and give it time to tack up before the next coat.

[@davidstepeck2644]

This is really cool Jerry. I'm itching to start, but have to make sure the frame and mechanicals are sound first.

[@LakesideAutobody]

Let me know how it goes. If you're spraying the frame, you can mix the paint a bit thicker. The mix ratio is really up to you and what works best for your project.

[@laverdadesmejor]

I understand that his is a 'budget' paint job, but why not add hardener?

[@LakesideAutobody]

You can do that for sure. It will add durability and dry much faster :)

[@larryanderson8049]

the definition of a wet coat.... I am assuming the same paint /thinner ratio... same air pressure...only more paint applied per square inch..in other words, closer or more passes or slower travel speed or all of the above?

[@LakesideAutobody]

Yes - wet to the point of running but.... don't run it :)

[@larryanderson8049]

@@LakesideAutobodynow your talking real experience!

[@limabravo6065]

Okbanyone who wants to do this here you go: Mix the rustoleum (alkyd enamel) with acetone to whatever consistency you like just don't go higher than a 50 - 50 ratio, then throw in an acrylic enamel hardener. Do not use urethane hardeners the chemistry is different. Using the enamel hardener catalyzes the paint, making it resistant to chemicals like gas and gives it UV protection so it won't go chalky like rustoleum right out of the can will. I offer this at my shop for cheap paint jobs as an alternative to certain chain store body shops like MAACO. Not that every Maaco is shit but a lot of them are

[@LakesideAutobody]

Thanks for the support and information my friend - have a good week :)

[@limabravo6065]

@@LakesideAutobody I was taught paint and body by an old Cuban dude at the hobby shop at my first base. He showed us how to use different types of paint and such. But when I see people who don't know what they hell thyre talking about in the comments telling people how a rustoleum paint job is a scam or only rednecks do this shit it gets my autism acting up

[@davidschworm9811]

Do I need a binks no 7 for this ? the epa took mine years ago. lol

[@hobbyelectronics6630]

I noticed that too. For non commercial use it would probably be OK. I still have my Devilbiss JGAs hanging in their cabinet.

[@larrysloan9296]

What’s the viscosity Keneth

[@goochi5544]

looks pretty good.

[@LakesideAutobody]

Thanks G :)

[@hazelwoodgarage]

I add enamel reducer and clear coat hardener to rust oleum, hardener makes it shine longer

[@LakesideAutobody]

That stuff works real well in the rustoleum - shines like real auto paint really.

[@claybird8184]

Thank you Jerry, I am planning on doing this on two old trucks this summer! Not show trucks, LOL!

[@LakesideAutobody]

I'm sure it will look just fine. Jerry

[@PhillipHall01]

Claybird how did the two old trucks turn out?

[@joeycmore]

Thank you for demonstrating quick, easy and cheap painting. If it's not too late, I'd love to know the approximate time between coats? Does it dry completely, or is there a trick to know when you can give another layer?

[@LakesideAutobody]

Generally with any paint auto or home, you would wait till the last coat is tacky dry or dry to the touch. Rustoleum drys slow and depends on warm temps to dry faster. Usually 1/2 hour to hour with Rustoleum and 10 minutes with regular auto paint :)

[@joeycmore]

@@LakesideAutobody Awesome. I really appreciate your taking time to answer my question. I'm off to paint my truck, cheap fast and easy like you taught. Cheers!

[@LakesideAutobody]

@@joeycmore Let me know how it goes and don't get discouraged if something goes wrong - there's usually something you can learn from it :)

[@shanesmaineshop]

I plan on painting my truck soon, and was wondering what a good mix would be for rust oleum. Thanks for sharing this video

[@LakesideAutobody]

You're welcome. I've heard of a mix ratio of 5 parts paint to 2 parts acetone too if you want to spray it a little thicker.

[@shortarms4114]

Rustoleum used to be cheap it’s now 28$ a quart. Without hardener or acetone so it doesn’t make sense to use anymore. I’m better of with a single stage. But it’s more problematic. Thanks for the upload.

[@LakesideAutobody]

You're right - better to just buy a gallon kit of TCP Global Restoration shop or something similar - better shine and more durable :)

[@sunnysacto]

nice info for 3 coats, soft tack, med and heavy last coat

[@LakesideAutobody]

I like using the hardener too - I didn't use it in the vid but it works well. Paint dries much faster - almost like professional automotive paint - nice shine too.

[@jcasey2309]

Lakeside Autobody when choosing hardener, is any specific brand best to mix with rustoleum? Also what amount is used? Thanks

[@socalluis2177]

How long of a wait in between coats?

[@LakesideAutobody]

I waited exactly 10 minutes but longer like 15 minutes might be better. Jerry

[@noeldavid5225]

C

[@jameswarren1871]

Can Rust-Oleum be sanded and buffed?

[@mrbigg7255]

James Warren yes

[@donaldappelhof2059]

Be careful not to wait to long! And especially on hot day. It will wrinkle the paint. Been there done that! 😳

[@bobwest9267]

Acrylic enamel hardner added 10% to your mixed paint will make it dry faster, harder and more chemical resistant.

[@fishhuntadventure]

Like auto body ‘hardener?’ Or the hardware store enamel paint additive(s)?

[@Viktory2k1]

@@fishhuntadventure Try a small amount of Japan Drier too

[@Barefoottaz1]

Enjoyed the video. No B/S and easy to follow.

[@LakesideAutobody]

I appreciate that Ray :)

[@slvrktman7824]

Big question…how much time before spraying second coat and then third coat?

[@LakesideAutobody]

Around 1/2 on warm days - 1 hour if under 70. Just check to see if the last coat is dry to the touch or at least tacky dry.

[@GrantP1974]

What was your air PSI set at?

[@LakesideAutobody]

Right around 20-25 psi. I keep it a bit low eliminate excessive fumes and over spray. It really doesn't matter as long as the paint is wet. Like a spray bomb can - real low pressure but you can still get great results.

[@ramoncruz9910]

That came out nice. Thanks for the information....👍👍👍

[@LakesideAutobody]

Thanks - have a great week :)

[@kellykirk5754]

Tractor supply has tractor enamel fairly cheap as well.

[@LakesideAutobody]

Thanks for the tip :)

[@ButtonBayClub]

Ive done 4 complete rustoleum paint jobs on cars using only rustoleum and acetone. no wet sanding. Heres my take on it. Pros- super cost effective, fairly easy to spray and youre probably going to be doing this to a beater of some sort so it will look wayy better than before. Cons- tendency to orange peel, long drying time, not as hard as real auto paint and you can expect it to lose some of its gloss within a year. Also I wouldnt do this to a car that you may want to repaint with actual automotive paint in the future.

[@LakesideAutobody]

Great advice - thanks

[@MLFranklin]

This is a pretty cool idea.

[@dyingforpie6879]

So mixing it with acetone thins it out - long term does it get a dusty look to it?

[@LakesideAutobody]

It won't hold up as well as real auto paint but it's much cheaper. Check out TCP Global or paintforcars.com for cheap but long lasting auto paint :)

[@4dirt2racer0]

i Fn hated my compressor kickin on all the time when i was tryin to run things like the die grinder so i simply plugged another air compressor into the manifold of the other one, now iv got more capacity And "twice" as much cfm its SOO nice, n so simple i was pissed when i didnt think of it before lol

[@LakesideAutobody]

Good idea Travis - thanks for your input :)

[@ericr5539]

What are the times between coats with and without hardner?

[@LakesideAutobody]

Rustoleum dries slow so 1/2 hour on warm days and 1 hour on colder days. Basically if the last coat is dry to the touch or at least tacky, you are ready for another coat :)

[@kevinmetcalf6371]

Nice job & video. Can that be done with an 8 gal. Air compressor?

[@LakesideAutobody]

Thanks Kevin - yes you can use an 8 gal compressor. You might have to let it catch up for a whole car but for small jobs, it should do just fine.

[@timgiesin4025]

The gun you used looked like my old Eclipse a Binks #7 clone which I still own and use when I spray large metallics

[@LakesideAutobody]

I have a clone too - only its a Campbell Hausfeld w/ a 1.7 fluid tip. Works just fine.

[@ronaldlewis4032]

@@LakesideAutobody Thank for sharing the tip size 1.7 toe is normally a primer gun 🔫I'll try that out too !! 😀

[@terryfrye4552]

Would I need a hardener for this? I wanna paint my chevy shorty van and some videos say to use a hardener

[@LakesideAutobody]

This will work for you - www.amazon.com/Valspar-4625-Enamel-Hardener-oz/dp/B000LNY1MY/ref=cm_cr_arp_d_product_top?ie=UTF8 - It will make the paint dry much faster w/ better shine, and durability. Good luck w/ the van and let me know how it goes - Jerry

[@codyramos3200]

yes if you want paint to dry fast n not be sticky if you have a Tractor Supply Company where you live they carry Majic catalyst hardener $16.99 1 8oz can is enough for 1gal paint.

[@Rusiputki]

Your question is the answer to why this is not an inexpensive job, might as well buy 2k paint. This enamel stuff hasn't worked for me in the reliability department. It's good for fence providing you don't lean anything on it...

[@alejandrocerda5098]

Yo so I’m painting my 85 c10 I used this process but I only painted around the front windshield will I be able to sand down with 1500 and re paint all the cab?

[@LakesideAutobody]

Sure. With solid colors you can do one panel at a time if you want. Really easy with rustoleum black or white - even the colors.

[@nathanalexander3425]

Would you recommend using a hardner?

[@LakesideAutobody]

Hardener like Majic Enamel Hardener works great with these oil based enamel paints

[@jeffrey4547]

i use rustoleum on some out side furniture and it oxidized and faded in one year from the sun so i don't think it will last on a car and by using it mite f up the next paint job if not stripped off the only way it would last if clear coat it with mixed in is hardener

[@LakesideAutobody]

If you use hardener with the paint it will hold up much better. Valspar 4625 Enamel Hardener

[@johng9562]

Cheap tools & materials represent the single biggest mistake DIYers make when approaching these types of projects. Remember tools are NOT an expense ~ they are an investment that you make in order to achieve superior results. They can then be sold for 85-90% of their value once the job is done and in the end it will cost less than renting. These 2 budget HVLP Systems are the best hold their value: 1st choice: Fuji 2202 Semi-PRO 2 (2203 gravity version) & 2nd choice: Earlex HV5500.

[@LakesideAutobody]

With repect, Binks, DeVilbiss, Sata, and Sharpe are examples of quality spray guns for automotive use. Many of the copies of these great guns work very well too for a fraction of the cost. I used a DeVilbiss copy for years in a professional shop and it sprayed real nice. Jerry

[@VinnyMartello]

Wouldn’t necessarily recommend it for car bodies but great for doing a chassis. All in all, good video and good job.

[@markhubanks3715]

Would you still put on a clear coat? Thank You!

[@LakesideAutobody]

You can - I 've seen some videos on it but I think a light scuffing or sanding after it cured would help the clear to stick :)

[@deweybell3529]

Thanks for sharing your knowledge

[@LakesideAutobody]

You're welcome - thanks for checking it out :)

[@douglasb.1238]

Excellent job, very nice.

[@LakesideAutobody]

Thanks Douglas :)

[@Floridaundercover]

Thanks

[@LakesideAutobody]

👍😊

[@SouthernEngineering]

Nice demo, you sold me. SUBed

[@williamchambers7235]

Howdy thanks for the video. Just wondering air psi and time between coats.

[@LakesideAutobody]

I'm usually at around 25 psi on every type of paint. For rustoleum you have to wait a good 1/2 hour or more. When it gets tacky dry, you're ready for another coat. Rustoleum runs pretty easy on vertical panels so go lightly at first.

[@redecho9669]

I find it weird how people that use rustoleum say you should never use more than 20% thinner. The results in this video show that 4:3 ratio is actually perfect and there is very little orange peel effect. I think that 20% is not enough since the paint is still too thick and it acts as droplets of paint instead of laying on well. Any thoughts on this? Maybe wrong paint gun pressure or setting because when i tried the finish wasnt as nice...

[@LakesideAutobody]

You can use as much or as little thinner as you want. What ever works best for you. Rustoleum is very thick and it would be difficult to spray if not thinned at least like.... 4:2 I think you could probably get good results at 4:3 or 4:2 right around there. Rustoleum runs easy too so be careful on side panels - give each coat time to tack up :)

[@johnandersen5321]

Thanks for the video. 😊

[@LakesideAutobody]

👍😊

[@jp8479]

How long do you wait between coats?

[@LakesideAutobody]

It depends on the temperature in the shop. Over 70 about 1/2 hour - under 70 longer. A good rule of thumb is when it gets tacky dry, it's ready for another coat.

[@gregshore5970]

Can you roll it on I don't have a sprayer and the room to spray if I did have a sprayer

[@LakesideAutobody]

Yes, just make sure it's dust free before rolling. You don't have to thin it when rolling it on - maybe just a little to get it to flow nicely :)

[@chandiaz7694]

Can Japan Drier be used on any type automotive paint?

[@LakesideAutobody]

I've heard it works well but have not tried it - good topic for a video though :)

[@edvisser3629]

How long between coats...between tack and second and so forth

[@LakesideAutobody]

All different times depending on temp 1/2 hour if warm - hour or more if cold. Best method is to check for tacky last coat or wait till last coat is dry to the touch. Hope that helps :)

[@chidexkofi8789]

Nice video

[@beestoe993]

Old school oil base auto paint. I'm going to use some tractor paint I got on clearance at cal ranch to paint my 73 Jeep, pretty similar. Question, how long do you give this stuff between coats? I know it dries pretty slow.

[@LakesideAutobody]

Hot days about 1/2 hour. Cooler days, you're going to have to check it and see if it is tacky dry or dry. Basic rule with any paint is once the last coat is dry or tacky, you are ready for another. 😊

[@beestoe993]

@@LakesideAutobody I took auto body in high school but that was more than a few weeks ago. 😁 Thank you!

[@demmdonn]

Rust-oleum has a deep red red color Think that's going on my 70 Galaxie

[@LakesideAutobody]

The hardener works well with it too: www.amazon.com/Valspar-4625-Enamel-Hardener-oz/dp/B000LNY1MY/ref=cm_cr_arp_d_product_top?ie=UTF8

[@JohnSmith-ki2eq]

Thank you for making this video, could you please tell me how long you waited between each coat?

[@LakesideAutobody]

About 1/2 hour @ around 70 degrees F. A good rule of thumb with any paint is when it gets sticky or tacky dry you can go ahead with the next coat. :)

[@JohnSmith-ki2eq]

@@LakesideAutobody Many thanks ☺

[@LakesideAutobody]

@@JohnSmith-ki2eq You're welcome :)

[@bena2293]

Hi Nice vid Rustoleum is a great Paint and it works Well with Interlux 333 Brushing Thinner which is expansive but dam it works letting you use a term call Rolling and Tipping its all over KZbin. I have used 333 with the 60 to 100 dollar a gallon Marine Paint for Topsides with great results but never tried it on good old Rustoleum until my contractor friend gave me 3 gallons of Gloss White Rustoleum and told me to me to paint my old boat it so ugly that it is scaring the fish. Dam it worked great now i just thinned it by eye but dam the end results looked like a very expensive spray job on my 20' Chris Craft i did for three gallons of Rustolleum a couple of foam rollers two packs of Beer and a Pizza.

[@LakesideAutobody]

Thanks for your input - always good to have for folks that need ideas on painting boats, farm equipment, etc.

[@glenstriper]

What was your mixing ratio for rolling and tipping? I'm painting an old campervan, using rustoleum topside paint, mineral spirits, penetrol, and Valspar hardener. Dont have anywhere to spray it, so I've got to roll it. Thanks!

[@keltingr2612]

I mix some hardener in but it has isocyanates so wear a mask always

[@LakesideAutobody]

Hardener does do the trick with this oil based enamel :)

[@jerryp2433]

What kind of hardener? I need to paint some suspension parts.

[@LakesideAutobody]

@@jerryp2433 It's called Majic Catalyst Hardener

[@ganeshnarayan5505]

Hello Good video and lot of great information.Q: can i spray urethane clear coat on top of Rustoleum.

[@LakesideAutobody]

I've heard of folks doing it but I have not. I would wait till the rustoleum completely dried - like a month or more then wet sand with 600 or finer. Then go ahead and clear it - can't really go wrong like that :)