Laser Poor Cut | Fiber Laser Poor Cut | Over-burning Cut | Solutions of Laser Cut

[@thefrenchneco]

As usual, very helpful. Thank you!

[@ClaraChai]

You are 🤗 welcome

[@shubhashrisokki.4375]

Helpful ... thank you

[@ijazmughal8494]

As usual Very helpful.👍

[@ClaraChai]

😀 thank you.

[@sounthavilaylomthongdy4646]

How to clear alarm 4limit

[@mstranger195]

Hi Clara . you didn't upload the focus tutorial video?

[@ClaraChai]

Later

[@mstranger195]

@@ClaraChai Ok . Thank you very much for your videos , that you share knowledge.

[@TutulTutul-bt2zk]

Hello madam we are in some problem with the laser raytools software. We mistakenly reseated the follower tool setup. And we did not taken any photo of this chart parameters. As well as we are the beginner about its operation. Could you please help us to setup its parameters and its operation.

[@ClaraChai]

Did you ask your supplier?

[@kacpertargas741]

Will it be the same for cutting stainless steel?

[@ClaraChai]

I don’t think so.

[@kacpertargas741]

@@ClaraChai Thank you :)

[@Brivannycherry-e8u]

Sorry my laser still have poor cutting i do kwon what the problem can you help me please

[@ClaraChai]

you can check my videos on poor cutting

[@medjoui7600]

Thank you What about the frequency of a laser source? I think it even affects the burning, if it is a high frequency

[@ClaraChai]

From my experience, frequency is not a parameter changeable often.

[@medjoui7600]

@@ClaraChai Thank you very much, but what is the effect of frequency if it is too high or too low?

[@kapechkong4343]

how do we find the correct focus for Mild Steel for example for 4mm 5mm 6mm 8mm and so on. Is there any rule for that?

[@ClaraChai]

Reference and experience

[@RotabSe]

Thanks, Do you have any information about cutting 2mm stainless without N2...only with air...pressure?, etc?

[@ClaraChai]

Could you check my another video, the parameters?

[@hasanudin617]

Apa penyebab head laser panas?

[@DivyaPatel-fi7fr]

during marking, it makes hole at corner high power at corners how to solve??

[@ClaraChai]

There is a setting in CypCut for corner power, you can check my CypCut videos

[@astitavsharma1238]

Hi, please help, I was watching your videos. I am cutting Galvanized sheet of 0.8mm thickness. Now a days there is lot of slag formation at nozzle tip which is causing cutting problem. Please suggest how to rectify this problem. As there was no such issue while cutting galvanized sheet.

[@ClaraChai]

Parameters not changed? Is the nozzle hot? Is your lens checked?

[@astitavsharma1238]

@@ClaraChai Lens is perfect. Parameters are fine. Still at nozzle tip slag formation is happening inside the walls of nozzle

[@ClaraChai]

@@astitavsharma1238 Your laser beam is not in the center.

[@astitavsharma1238]

@@ClaraChai we have cross checked the laser beam centering. That is fine also.

[@saaww33]

we love you ❤️

[@ClaraChai]

Thank you

[@hariharankannan]

Hi mam we use ispri laser head auto focus head but when I cut carbon steel with air like 3mm the focus position automatically going to -30 after coming alarm servo

[@ClaraChai]

[phone], please give me more.

[@lennujaihab]

how about the wavy cut, the cut is not straight.

[@ClaraChai]

What kind of wavy? Could you show me a video?