How to Replace Low Beams In a 2013 Ford Fusion with Lasfit LA Series H11 Bulbs

[@lasfitvehiclelife]

🎄Get a free pair of 168 LED bulbs!🎄 A special event for KZbin subscribers, celebrate Christmas with Lasfit! Join now: www.lasfit.com/pages/2025-special-forum-youtube-sponsorship-program?Social&YTB+Channel&Christmas+Sponsorship

[@moussaniang4445]

You have no ideaaaa how much this video helped a lot of fusion owners. You Sir, are a savior 💯💯💯

[@lasfitvehiclelife]

😎😎😎😁😁😁👍👍👍

[@AquivaStar]

Of all the videos on KZbin on how to remove the headlights from the Fusion, this is the easiest and most detailed! Thanks a million!!!

[@lillylove4790]

Johann Botha I agree, all the other videos require you to either lift the car and use special equipment and use words I don’t understand lol even I can do this myself now !

[@rgruenhaus]

You try getting those bumper corner covers back on and to stay! The system of clips to hold the upper fender with the bumper cover is the weakest ever. I worked in body work years ago and bolts were the best way to secure sections of fender.

[@XxGpZXX]

This video helped so damn much. Crooks at dealers and local mechanics wanted to charge so much and this is the only video that actually showed how to correctly do this.

[@stevebrown162]

It takes about an hour to do that. Should people work for free? They should charge you about $120-150 to install them, at todays rates.

[@ChrisFindley]

Brother, you saved my life last night. I'd watched half a dozen other vids before diving into this job, trying to find the cleanest method. Several mentioned 'you don't have to take off the bumper but here I go anyway' and I couldn't find anyone specifically identifying what the minimum job looked like. Two hours later I'm still trying not to take off the bumper. I'd managed to get one H11 out of the housing but could not get enough leverage on the bulb to twist it back into a locked position. So many swear words and screws on the floor appeared as I dug deeper and deeper into the bumper and surrounding hardware. I was giving up and accepting that I had to take it all the way off, plus skip sleep altogether to finish before the wife needed to drive to work. Then I came across the first 3 minutes of your video and it was like rain-clouds being destroyed by pure sunlight. A few minutes later I had the bumper loose enough to pull the headlight housing forward and finally get my hands on that little explicative. Another few minutes after that the other H11 was done and it was just a matter of putting all those unnecessarily removed screws back in place. Now replacing the low beams feels like it would be less than a 30 minute job. Thank you, thank you, thank you.

[@lasfitvehiclelife]

Wow, that's great. 👍 We're glad this vidoe is helpful for you. Are you satisfied with the LED bulbs?

[@Alaskan_Two_Spirit_Wolf]

Thank you for this part right here. I was able to take off n replace headlights from another mechanic video but not able to get back on with what they show. But your video helps. I think 😅 I had so much trouble last night. About to check to see if your video helped. 😊

[@neoknight14215]

Thanks you gave the full breakdown while many others skipped over the full visual.

[@lasfitvehiclelife]

Glad it's helpful for you. 😊

[@StarTurtleZero]

Thank you for taking the time to put together a detailed and easy to follow video. The other videos were either too involved to remove the entire front bumper or didn’t provide sufficient room if you didn’t remove the clips of the bumper. This is easily the best solution.

[@soljah94]

Thanks for this video! I just finished replacing my low beam bulbs on my 2014 Ford Fusion. I had a few extra screws that needed to be undone that we're not shown in this video. Other than that, great video and It made my job much easier! Thank you!

[@lasfitvehiclelife]

Thanks for your feedback, which is useful for other guys.

[@mafiaspyder504]

I swear I did the installation today May 17 2020 not hard but time consuming thanks for the video I literally did it because of this specific video make it look easy. I also bought the LASFIT LEDs change the low beam and fog lights. You helped me save some money!

[@lasfitvehiclelife]

Wow, great! 👍👍👍👍👍👍

[@hmroa3056]

Where you able to replace the dust cover or did you have to leave if off because of the size of the LED adapter cable?

[@lasfitvehiclelife]

Hi, the dust cap can fit back on the housing, and we have not received any feedback regarding issues with reinstalling the dust cover on the 2013 Ford Fusion low beams.

[@jeffh6889]

Awesome video, brotha. I'm doing this repair for a friend later today and this is exactly what I needed so I'll be prepared. You are appreciated!

[@ireign7579]

Great video. Helped me out a lot. Took only 45 minutes

[@lasfitvehiclelife]

Glad it helped。 😀

[@BrayanFrias402]

Of all the videos that I have been looking for, yours is what is the best that best explains Thank you I did it and I look good

[@lasfitvehiclelife]

Glad it helped. What's the year of your Ford Fusion?

[@sajen23]

i bought fog lights for this car, looks like i should check the bulbs while i install dem fog lights, since u have to dismantle half the car anyways. TY for vid. :)

[@kevinengle2000]

Excellent job explaining everything

[@lasfitvehiclelife]

Glad it helped.

[@royjimenez6789]

Thank you so much for the information

[@lasfitvehiclelife]

We are glad that this video can help you! Could you please kindly tell us the year and the trim of your Ford Fusion and whether you purchased lasfit product?

[@royjimenez6789]

@@lasfitvehiclelife is a Ford fusion 2014 and I did buy the bulbs and Advance

[@lasfitvehiclelife]

@@royjimenez6789 Thank you for your reply. If you purchased Lasfit H11 LED bulbs, could you please share us with some pictures or videos about the installation or the visual effect? You can get support from us if you have any problems with Lasfit products.

[@mgreene5150]

This was a very helpful video. Thank you. On future videos, it would be helpful to know what size bolts and torx bits we would need.

[@lasfitvehiclelife]

Great suggestion! We'll do. Thank you!

[@coolissimo69]

What a saviour.Thanks bro.

[@lasfitvehiclelife]

Happy to help.

[@americanwoman7324]

Thanks brother, saved me the cost of labor!

[@usmcgrunt02]

DO you stuff the ballast and everything behind the rubber weatherseal?

[@ronaldsmith6367]

Great job and simple. Thanks

[@lasfitvehiclelife]

Glad it was helpful!🙂

[@hoagybob]

An excellent video that covers very important details. This isn't a simple job.

[@lasfitvehiclelife]

Thank you.

[@janinelehiy5169]

This is exactly what wasn’t done I had horrible light pattern shines on the shoulder instead

[@lasfitvehiclelife]

Please check if the LED chips toward at 3 and 9 o'clock.

[@vertboyz]

the best video yet this was real easy this way -- thank you

[@omarvela7135]

Thank you so much...you bailed me out big time! I appreciate it!

[@lasfitvehiclelife]

That's great. 👍

[@kevindiaz3459]

I tried this without popping out the bumper, I just can't get my hand in there. Saw a video where someone was able to just loosen the headlight and get it, but it looks like I will need to use this method instead to replace the low beams. My hands are too big. Nice to see it isn't hard to get the bumper to come out. Just hate dealing with those clips!

[@lasfitvehiclelife]

Yes, there are two options for vehicle owners to replace the factory halogen bulbs, one is to take off the bulb from the hood, but sometimes it is hard to do that, the other you can try is to take off the bumper and replace the bulb.

[@damineo1322]

Great video !!! Do more about this car.

[@4080Project]

I ordered two pair, low beams and fogs...thanks for the video!

[@lasfitvehiclelife]

Thank you for your support to Lasfit. What's the year of your fusion?

[@4080Project]

@@lasfitvehiclelife 2013, noted in the order, went with the Plus series so it fits and able to rotate from what I read, costly but hopefully last pair I have to purchase!

[@lasfitvehiclelife]

@@4080Project Looking forward to your feedback about how they work on your fusion 😀😃

[@4080Project]

Getting the lamps out was a pain! Couldn't get the passenger light level, slight blind spot on far right turns! I'm too lazy to pull out again to fix. 3 out if 4 lights are great, no issues!

[@Flex4LX]

I replaced mine today. I have small hands so I just reached down and twisted out the bulb. Then I just removed the screws from the housing as well as the ones on top of the bumper just for slight wiggle room. I pushed the new bulb in the housing by twisting and fidgeting around until it locked in place. Thats it. 10 minutes tops.

[@lasfitvehiclelife]

Great! Thank you for your feedback. May I ask the year of your Ford Fusion?

[@neilreid9005]

Really good instruction- great job. Am going to order the LED's for my 2016 Fusion from you guys. Well done.

[@kelvo1k505]

Neil Reid I have a 16 also , did you end up ordering ?

[@neilreid2298]

@@kelvo1k505 - Yes.

[@xXguardian951Xx]

Better than removing the whole bumper, and way better than doing oragami with your hand to not remove the bumper, great video!

[@lasfitvehiclelife]

For most vehicles, it no needs to remove the bumper if the headlight housing is big enough to hold your hand to reach the stock lights. What's your vehicle make, model and year?

[@mitchlopez7408]

Thanks it worked awesome it was a little different because i have 2015

[@lasfitvehiclelife]

Sounds great. 👍

[@Sethry_]

Do your headlights flicker? I read that was a common problem

[@FadeToBlackLLC]

I just sold a set to a customer with a 2013 Ford Taurus and I think he needs to adjust like you mentioned.

[@lasfitvehiclelife]

LAplus series H11 is adjustable socket. After locking it on headlight housing, you can rotate it to adjust the beam pattern.

[@dumper707]

Great way to explain

[@lasfitvehiclelife]

Is your car 2011 Ford Fusion?

[@zachg2081]

I’m glad I found this video bc I just put lasfit leds in my low beams and put them in however and the pattern seems off and kind of dim so now I’m gonna check

[@lasfitvehiclelife]

Hey, you can adjust the beam pattern by turning the LED bulb.

[@GhostCodeRG]

i got the two screws off and the retainer bracket but the light still wont come out

[@lasfitvehiclelife]

May I ask if you installed Lasfit bulbs? If so, you can contact our customer service team at [e-mail] and attach pictures describing your issue. Our team will do their best to assist you and resolve the problem.

[@CharlotteSham-w5z]

My low beams look like there is a window shade pulled partly down - the light beam is not fully round. Does this mean there is a collar alignment issue? How do I know for sure? Thanks.

[@lasfitvehiclelife]

Hi, are you using Lasfit bulbs? For these bulbs, could you please check if they are installed correctly? The correct direction is the LED chips facing side by side with the wire cord down at 6 o'clock. Here is a video for your reference: kzbin.info/www/bejne/npW6kouObK6NbpI

[@JoseArias-jr7lx]

I’m thinking about doing to to my low beams and high beams and day time running lights

[@lasfitvehiclelife]

Sounds good. Looking forward to your update. If you need any support, feel free to contact us. :)

[@flyboy8364]

Why do my new LED headlight's flicker a little when I use my turn signals?? 2014 fusion hybrid

[@lasfitvehiclelife]

Don't worry. When you use your turn signals, the current is not table, so the headlight is a little flickering.

[@flyboy8364]

@@lasfitvehiclelife thank you for replying, is there a way to fix it?

[@jw6210]

Any tips on removing the headlight? Mine seem to be stuck on the guide pin.

[@lasfitvehiclelife]

Hello, do you need to remove the entire headlight assembly? What problems are you running into?

[@cryptomomentz]

looks like a 2013 breh

[@joeg.1119]

How the lighting out put is it good? Is not too bright cause I don't want to blind other driver when I be driving please let me know so I can buy this.

[@lasfitvehiclelife]

Don't worry, no blinding. I recommend the upgraded version to you, LAplus series, here is the link: bit.ly/2Xsitbi

[@jaimevillanueva5131]

Hi. Wanted to see how I can resolve the flickering headlight when I activate my blinker? I installed the Lasfit LED.

[@lasfitvehiclelife]

Hello, what's your vehicle make, model and year? You have installed Lasfit T series LED turn signal bulbs, right?

[@jaimevillanueva5131]

@@lasfitvehiclelife 2014 Ford Fusion and i installed LA Plus Series H11 H9 H8 LED Bulb 60W 6000LM 6000K Amplified Flux Beam

[@lasfitvehiclelife]

@@jaimevillanueva5131 They only flicker when you activate your blinkers, right? Could you kindly shoot a short video for showing your issue? It will help us know more details and fix the issue soon. Thank you!

[@jaimevillanueva5131]

@Lasfit Auto Lighting I created the video but I’m not an expert with tagging. I think I did it correctly.

[@MarceloAVillegas]

I bought these but they didn’t come with the wiring harness, so they are flickering… do you have a solution for this?

[@lasfitvehiclelife]

Hello, what's your car make, model and year?

[@MarceloAVillegas]

@@lasfitvehiclelife I have a Ford Fusion SE 2014

[@No_Name8567]

So the rubber weather cap stays off ? If it stays on can the fan on back of bulb still remove enough heat to be efficient?

[@lasfitvehiclelife]

you would have to modify the cap a bit to allow it to get back on. And yes it should still work with no problem due to the hot air is able to go out though the headlights vents.

[@rgruenhaus]

Modify the cap? Bad engineering!

[@lasfitvehiclelife]

@@rgruenhaus You could use an after-market rubber cap

[@markcrew3696]

I understand what you're saying these lights have little fans on them if you put the cap on will it make it too hot I thought about just cutting a small little hole so air can get in there but I'm just going to keep tabs on mine when my lights are on I'll check and see if it's getting too hot in there if it is I'm a put a little slat or slit our little hole for the fan to get air but I would not recommend taking off that entire dust cap and just discarding it. I would put a little small hole in it but wait and see how hot it gets in their first. This is a great question I ran across the same thing.

[@dennybirchfield]

U can reach it without taking out the while light

[@lasfitvehiclelife]

Yes.

[@jmdrno]

I recently installed these very bulbs on my 2016 Fusion. Looks great! But this morning I ran into a small problem, I found that my headlights fogged up. It’s been extremely humid the past couple of days so that may be the cause. Also when I installed the bulbs I was not able to put back the dust cap bc the back side of the bulb would be touching and I didn’t want to risk anything. So you have a suggestion as to how to fix and avoid it from happening later?

[@lasfitvehiclelife]

You could turn on headlights about 10-20 minutes, because the LED bulbs generate heat when they are working, which could evaporate the moisture

[@mikejr2435]

Any special or specific tools needed to take off any of the pieces that need to be removed

[@lasfitvehiclelife]

flat head, a 10 mill and ratchet possible extension if needed.

[@dougwitherby3291]

Well done 👏

[@lasfitvehiclelife]

Thank you 😁

[@kelvinclaxton4026]

Do you have a video for the fog lights as well?

[@lasfitvehiclelife]

We don't have a video for the fog light. For 2013 Fusion, the fog light is H11, the same bulb size as low beam. You can find the fog light location, and twist it out, then install LED bulbs. H11 LED bulbs fit fog lights for 2006-2018 Fusion: www.lasfit.com/products/la-plus-series-h8-h11-h16-led-fog-light-bulb?Social&YTB%20Channel&LAplusH11-fog

[@reeseyoung7282]

I got these but the leds flicker when I turn my turn signals on what should I get a decoder?

[@lasfitvehiclelife]

Hello, did you change your turn signal lights to LEDs?

[@mrmister8546]

Thank you!! Great video. Appreciate it!!

[@westonhalstead8636]

How did you change the orientation of the white part?

[@lasfitvehiclelife]

Hi, the socket of the upgraded version is adjustable, you can rotate the LED bulb to change the orientation: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB

[@TOPBOSSJAMES]

Is the collar rotation gonna be the same for the driver side?

[@lasfitvehiclelife]

Yes, the same direction. What's the year of your Fusion?

[@TOPBOSSJAMES]

@@lasfitvehiclelife its a 2016

[@ReassuringSmile]

Is that CANBUS required?

[@lasfitvehiclelife]

No CAMBUS is required.

[@kevinjackson8422]

I just upgraded my DRLs to LEDs, they only come on when the low beams are turned on, any suggestions?

[@lasfitvehiclelife]

Hi, what's your vehicle make, model and year? Did you purchase LED lights from Lasfit?

[@kevinjackson8422]

@@lasfitvehiclelife 2014 Ford fusion no I did not purchase of that brand

[@lasfitvehiclelife]

@@kevinjackson8422 Ok. We suggest you ask your dealer for help. We're not sure how you upgraded your DRLs to LEDs

[@abdulrehmanmalik5484]

Do u guys sent to europe? I wanto order

[@lasfitvehiclelife]

Hello, it's a pity to tell you that we don't ship to Europe at present.

[@jeeptj08]

How do you adjust the LED light?

[@lasfitvehiclelife]

LA series LEDs need to take out the screw on the socket retainer, then adjust the socket. LAplus series is an upgrade version, 360° adjustable, you could get more information for LAplus series from this link: ebay.to/2zW7j4P

[@JBIRD98]

My 19 don’t have to remove the headlight but I think you gotta cut the housing to fit led I bought the auxbeam h11 s2 and they won’t go because of length

[@lasfitvehiclelife]

Hi, we didn't cut the housing. But now, we have new LED bulbs, smaller size. We tested these LED bulbs on 2019 Fusion's low beam, perfect fit: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB

[@joshuagutierrez3506]

I tried putting led bulbs in my 2019 Ford Fusion and it didn’t create a good pattern, is it bc I have reflector headlights?

[@lasfitvehiclelife]

Hi, did you try to adjust the beam pattern? BTW, did you purchase LED bulbs from lasfit.com? or you bought from other brands?

[@gemini212102]

What site can i buy some for 2016

[@lasfitvehiclelife]

For 2016 Ford Fusion, the headlight low beam also is H11: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB

[@lasfitvehiclelife]

For 2016 Ford Fusion, the headlight low beam also is H11: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB

[@1_luismm]

@@lasfitvehiclelife so are these better and easier to fit than the previous version? I just ordered some

[@lasfitvehiclelife]

@@1_luismm Sure. This is upgraded version. Will you install them by yourself?

[@1_luismm]

@@lasfitvehiclelife yes

[@bigboycervantes5240]

You have something for 06 ford fusion

[@lasfitvehiclelife]

Yes, below LED lights fit 06 fusion: LED headlight low beam: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series Reverse light: www.lasfit.com/products/lasfit-t15-912-921-led-interior-reverse-backup-trunk-center-high-mount-stop-dome-light-bulbs-6000k-pure-white Front turn signal light: www.lasfit.com/products/3157-switchback-led-turn-signal-lights-canbus-error-free

[@torysanders3806]

Thanks!

[@vendrick4571]

I installed some LEDS and now I have a B1D00, B1D03, and a B1D02 codes popping up anyone know how to fix that???

[@myboringadventures]

Weird, my 13 had a clip in that tab on the bumper cover to fender.

[@lasfitvehiclelife]

You need to remove the clip, right?

[@myboringadventures]

@@lasfitvehiclelife yes. The bumper cover wouldn't pull away from the fender.

[@lasfitvehiclelife]

@@myboringadventures ok. Welcome to share some pictures with us. 😀😃😁

[@myboringadventures]

@@lasfitvehiclelife I'll try when I rip into it again

[@Trashman702]

Why do they have to make something as simple as a HL so damn hard to replace ?

[@lasfitvehiclelife]

LOL. Some compact-size vehicles' headlight housing is too narrow to reach the headlight bulbs, and it has to be removed the whole headlight and install the LED bulbs.

[@YourPointOfViewPodcast]

I fit my hand back there it was hard though

[@kevinwhite6304]

You do not need to remove those 2 10 mm bolts. You only need to remove the black torx and the silver torx.

[@lasfitvehiclelife]

Thank you for your feedback. 👍 It's easier to remove the headlight if remove those 2 10mm bolts.

[@agenericaccount3935]

Yeahhh, thanks Ford. 27 clips and fasteners, bumper removal. To replace a headlamp bulb. Special place in hell for design engineers who have never worked on cars.

[@ghostsaintpatrick3959]

You didn’t show how to remove the head lamp housing

[@lasfitvehiclelife]

Hi, it doesn't need to remove the headlight housing, You can reach the stock halogen bulbs and replace them with the LED bulbs.

[@davegallop9357]

I like the way you don't show that the standard rubber covers don't actually fit properly over the cooled (fan fitted) LED lamps and you conveniently fail to show that! I believe you should be a wee bit more honest about that, as it ultimately will allow water ingress into the lamp unit and result in a destroyed entire unit!

[@lasfitvehiclelife]

Thanks for your suggestion.😊 As we know, these LED bulbs fit on most of vehicles perfectly. If we have the situation as you said, we'll display and tell how to fix it. We're collecting more ideas, and surely show more details in our videos.

[@ChrisAutoBurleson]

left out 2 bolts under headlight

[@samliang4146]

its not ok, OK?

[@MrMonster2020]

This is not a 2012, 2012 was old body style fusion

[@lasfitvehiclelife]

Yes, you're right. We revise the year in the title. Thank you

[@thomasn7025]

Wrong year. Changed fusion for 2013.

[@lasfitvehiclelife]

Thank you, just revised the year. for 2006-2018 Fusion, the low beam is same bulb size, H11.

[@iMr.Jetpacks]

This is not a 2012, I had a 2012 and it was the other body style!

[@lasfitvehiclelife]

Hi, this is 2013 Ford Fusion. Do you want to replace the OEM headlights with LEDs for your 2012 Fusion? The low beam bulb size also is H11, here is the link: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB

[@rgruenhaus]

The first thing you say in the video is that you are working on a 2012!

[@lasfitvehiclelife]

It is 2013 Fusion 😂

[@DanielSanchez-vg3pz]

Chanse si iso eras tu video en español tendrías mucho más vistas. Por ejemplo yo

[@lasfitvehiclelife]

Gracias por tus sugerencias.

[@ctsstxc]

On my 2015, the clips are diffrent.

[@lasfitvehiclelife]

Could you take some photos of your clips to send us for a look by email? [e-mail]

[@miguelsuarez-solis5027]

In all seriousness... Fuck Ford for making changing a headlight this complicated

[@sajen23]

I learned 3 things today #1 i purchased this ford fusion not noticing how much "snappy on and off" bull shit there was on this car #2 Ty for this video but FK all this shit, it used to be just u had to shimmy ur hand in at a weird angle and twist to remove a bulb. So lesson #2 is pay this guy to do this for me. #3 I bought a dodge ram and didnt know how far they shoved the engine back into the firewall, hard to work on.. So Lesson #3 is i apparently need to do more research on vehicles than i already do :( Mission Failed, We'll get em next time!

[@CharlotteSham-w5z]

Agree this is too much work to replace a bulb. Now I have to take my car to the garage! $$$$$

[@lasfitvehiclelife]

Thank you for your comment! The installation process can be a bit troublesome, but it might be worth a try for a better lighting experience : )

[@lasfitvehiclelife]

New video for 2019 2020 Ford Fusion LED headlight bulbs installation: kzbin.info/www/bejne/qXrSqqxueqmqn5o

[@antoniopagan3990]

Are these bulbs low beam and high beams?

[@lasfitvehiclelife]

@@antoniopagan3990 These LED bulbs fit low beam only. High beam is H7. Could you take a photo of your high beam bulb, and the factory headlight housing to send us for a look? If the high beam bulbs come with a retainer holder, the standard H7 LED bulbs do not fit. We'll recommend compatible LED bulbs to you. contact email: [e-mail]

[@sanitarysacrament_trays7470]

I found a much better way to do it without loosening the fender and removing the headlight assembly. I did this way first and it caused my headlight to be way out of alignment. I then tried kzbin.info/www/bejne/qqrVo36mqNeagsUfeature=shared from Driver Mod on the other headlight and it was much easier.

[@aa1yhm]

This is bullshit, there's 2 bolts under the headlight assembly need to be removed in order to pull out the headlight 🙂

[@lasfitvehiclelife]

could you please tell me the year of your Ford Fusion? Maybe it's install differently on different vehicle.

[@mattbroaddus6688]

That fucking headlight dont come out.

[@jpsailorallaboardmatey461]

Never getting another Ford, pathetic it’s this involved to change a damn bulb.

[@lasfitvehiclelife]

Limited sponsorship for Newest LED Bulbs Testing Provided. Don't hesitate to contact us to grab this opportunity. 1. Contact email: [e-mail] 2. Please tell us your vehicle make, model and year

[@lasfitvehiclelife]

Buy LED low beam bulbs + license plate lights = 5% OFF Upgraded version low beam bulbs, LAplus series H11: www.lasfit.com/products/h11-h9-h8-led-headlight-fog-light-la-series?Social&YTB%20Channel&LAplusH11-LB License plate lights: www.lasfit.com/products/2x-lasfit-t10-192-194-168-158-led-interior-light-bulb-error-free-1-year-warranty?Social&YTB%20Channel&L-T10-White

[@rod1575]

Worst design. What were Ford thinking?

[@lasfitvehiclelife]

😆🤣

[@itsjustprecious6365]

I hate Ford Fusion I’ll never buy another ford again