LED Sequential Turn Signal Strips + DRL and Start Scan

[@AutoSensation]

Affiliated Product links: 👉Amazon - amzn.to/49g65Qg

[@migalancitosanchez7688]

@AutoSensation Why do my LED strips turn on when the car is off?

[@AutoSensation]

@@migalancitosanchez7688 Change your red wire connection. Make sure that the fuse that you connected to is off when the vehicle is off.

[@migalancitosanchez7688]

​@@AutoSensationWhen I turn off the car, the LED strips turn off, but after 4 or 5 hours, they turn back on. I think I did the job right, but for some reason after 4 or 5 hours they turn back on. Do you have any recommendations?

[@AutoSensation]

@@migalancitosanchez7688 Yes. Connect the red wire to a different 12v source.

[@migalancitosanchez7688]

​@@AutoSensationCould you help me and show me which one is on the 2016 RAV4 XLE? I don't know what other source I should connect it to, since I'm not very good at this, please.

[@billybrown640]

Finally a video that's not double speed or you can't and skipping steps. Thank you.

[@Em12k]

I finally installed mine today, went a little different route with the wiring and the tucking In of the led strip, over all I'm happy with the result makes the front end look better

[@AutoSensation]

Nice

[@gregoryharris8219]

If you have the longer version are you able to cut the wires and they still work with the sequential startup pattern

[@AutoSensation]

If you have the headlight version yes you can cut at certain points. If you have the hood version you cannot cut.

[@gregoryharris8219]

@@AutoSensation Thank you so very much what a tremendous help

[@AutoSensation]

@gregoryharris8219 your welcome

[@big827]

can you explain what you used for the pin head. Is it littterally a pin?

[@AutoSensation]

I used these. amzn.to/3IWUQkn I also pinched it a little smaller so that i can push through the back of the harness.

[@rmsys18]

Can you use this as a brake/tail light also?

[@AutoSensation]

No. The color will not be red. The sell red ones if interested for tail lights. amzn.to/4b1dLr4

[@n3m3th]

Could you explain the pin? What kind? Did you solder it to the wire?

[@AutoSensation]

amzn.to/4fqzUk0 best if you solder but not necessary

[@Abraham-ui6kc]

How did you trim the pin connector so it can fit in the harness?

[@AutoSensation]

I just cut with scissors

[@smukund5]

Red wire is connected to Parking Light. Does this mean DRLs work only when you are driving with the Parking Light on? What about the Rear Parking Lights, do they too have to remain on to keep the DRLs on.

[@AutoSensation]

Yes. It will work to whatever the power source it's connected to.

[@sioreqx4443]

I have a 17’ Honda Accord LX, and don’t have a drl plug, only has low beams, how could I make the connections to make it work, I’m not going to be using the indicators. Pls help

[@AutoSensation]

try connecting the red wire to fuse 20 or 22 in the engine fuse box. make sure they shut off when the engine is off.

[@sioreqx4443]

@@AutoSensation and then the other one to the fuse in the passenger fuse box right?

[@AutoSensation]

You can or you can connect both to the same fuse@@sioreqx4443

[@sioreqx4443]

@@AutoSensation imma use a “add a circuit”, not going to wrap the wire around the fuse

[@AutoSensation]

@@sioreqx4443 Yes. I highly recommend that way. It's much safer

[@mjyumping]

Can you wire this so that the white light comes off when you use turn signals, but not turning yellow light on?

[@AutoSensation]

I'm not sure how to do that

[@Lawlesslarry69]

Thank you for the video! Where did you get the pin you mentioned at 3:20?

[@AutoSensation]

amzn.to/49FnOQY

[@Lawlesslarry69]

@@AutoSensation you're awesome! I've subscribed!

[@AutoSensation]

@@Lawlesslarry69 Thanks for your support

[@davinmars5177]

Great video. What wiring method would you recommend for a car that doesn't have DRL(therefore no DRL wire). I'm not confident with the fuse box stuff nor looking to use the charging port as I connect other things there. I am leaning towards connecting the white light to the fog lights (willing to keep them on if not a bad idea) then connect the yellow to the turn signals. Any thoughts or suggestions? Thanks

[@AutoSensation]

You can tap directly to fog light wire or parking light wire. Just make sure you water proof the wire connection with electrical tape or something to prevent corrosion.

[@idrisahmedi4686]

How does push pin work? So I don't need to spice or anything

[@AutoSensation]

Yeah. I just push behind the harness in the correct wire. I will suggest to mabe add some liquid tape to prevent corsion.

[@idrisahmedi4686]

@@AutoSensation Thank you, can't wait to do this, I was very worried about splicing wire for the turn signal wires. My led strip came with push pins attached already which I didn't know what it was for untill I watched your video and saw how you just pushed it in behind the harness, now I can finally put the light on my suv.

[@Maver2021]

Ciao, io ho montato la stessa striscia, però al cofano posteriore, funziona tutto bene però solo a motore spento. Appena metto in moto il motore dell'auto, la striscia non funziona più. Cosa può essere per te ? Grazie e complimenti!!

[@reflektion1791]

I have the Same drl but why i have Just black and Red cable ? And you have 3 cable ??

[@AutoSensation]

Sounds like you have a different one. If you don't have the yellow wire it does not have the turn signal.

[@lukeschaeffer2551]

So if I'm doing it on my motorcycle with signal lights that are separate from the headlights (on the side of the bike), then i just need LED strips with wires and connected them directly to the wires of the existing signals...no need to mess around with the DRLs?

[@AutoSensation]

Yes

[@Junior-db2rl]

Are they bright as the stock headlights or do they reduce brightness?

[@AutoSensation]

I would say not as bright as the stock headlights but may as bright as the stock DRL's.

[@daddyjoespizza7809]

Hi there! I have a slightly older toyota, but i don’t have DRL’s stock. Would I just wire into the nromal headlight wire? Also, I have very bad with wiring, but i don’t understand what you did with the yellow wires. would it be okay to just splice them in normally? Thank you so much!!

[@AutoSensation]

Yes you can wire to the normal headlight. When you turn the headlight on the LED strip will turn on as well. You can alternatively find a fuse that turns on when the vehicle turns on and tap into that. Now you have DRL's. Yes you can splice them just make sure you use electrical tape or liquid tape to seal and waterproof your wiring.

[@brianjamesrivadulla2589]

what if I don't have DRL lights? where can I tap the red wire?

[@AutoSensation]

Your parking lights will work or headlights. However it will only turn on when your parking lights or headlights are on. Try tapping into a radio fuse or cigarette fuse

[@gantoniom9615]

If my car doesnt have led headlights this led strips are compatible ?

[@AutoSensation]

Yes. It will still work

[@Rnbsoccerstar7]

Can you still change the lower or high beam in your headlight with this led strip and all the wire on it?

[@AutoSensation]

Yes. Everything will work normal

[@Rnbsoccerstar7]

@@AutoSensation Okay cool nice to hear it because i have to put my headlights out to change the low and high beam on it

[@theamazinggoldfish8713]

I just got those for my car but after looking there isn't enough room for installation around the headlights. I might try them (with out the turn signals) inside of the grill. 😂

[@Joe-ut4ee]

Thank you this was hard for me to figure out but you showed me what to do

[@AutoSensation]

Glad this video helped you out.

[@DaniSpooks]

where or how did u make the pin so u didnt have to splice

[@AutoSensation]

I made them. amzn.to/3ZwTPac

[@DaniSpooks]

tytyty i am gonna use these to wire my drl turn surond for my car@@AutoSensation

[@moaletaufa]

How do i install it on my ford ranger?

[@AutoSensation]

Connect the black wire to ground or an unpainted bolt, red wire to positive of your parking lights or DRL and yellow wire to your turn signals. You may need to extend the wires to reach.

[@theodorevelentzas1065]

Where do you connect it if your car does not have DRL standard on your car, the ACC

[@AutoSensation]

You can connect to any acc fuse

[@theodorevelentzas1065]

I noticed I have a pair of Fog lights that have been removed but the connections are still there, there is a white and black from the old fog light connection, I just want the white DRL light not the Amber to work so the current amber hooked to the car will work via its OEM, so based on this which wires do I connect to the old Fog light connectors which are black and white and will it work if I only connect the DRL white not the amber. Thanks excellent work

[@AutoSensation]

@@theodorevelentzas1065 theoretically yes. You will have to make sure the switch on the dash is on.

[@newgame09794]

Hello, I have the same DRL strip. I can make the white light turn on by tapping the red and black on my parklights but the turn light (yellow) doesn't work when I tap it on my turn signal positive wire.

[@AutoSensation]

When you tap the yellow wire to a positive is the black wire still connected? I would test directly to the battery terminals. Yellow to positive and black to negative.

[@newgame09794]

@@AutoSensation yes. When I tap the yellow wire, the black wire is still connected to the negative line of the parklight. I tested it directly from the battery and the drl works fine.

[@genesisdigma7417]

@newgame09794 Do you find a way to fix it?

[@genesisdigma7417]

@@newgame09794do you find a way to fix it?

[@newgame09794]

@@genesisdigma7417 nope

[@denielcontreras7683]

can i make a question can i cut if its over size?

[@AutoSensation]

Yes you can cut them.

[@gantoniom9615]

How to conect the strips if i want only the yellow turn signal lights?

[@AutoSensation]

Connect the black wire to ground and the yellow wire to the turn signal power source

[@gantoniom9615]

@@AutoSensation I did that but the led strip doesn't light up at all

[@AutoSensation]

@gantoniom9615 try testing by using a battery. Tap the black to a negative and yellow to the positive. This is to make your your lights work

[@gantoniom9615]

@@AutoSensation yes this way my led strip works

[@AutoSensation]

@@gantoniom9615 okay. No we narrowed it down to a connection problem. Check your connection to make sure the have power. Where are you connecting the black wire to?

[@gorillasoulja2376]

What year was that Pilot u were working on?

[@AutoSensation]

2019 touring

[@jomarisantoskd35]

Where do you get the pin connectors

[@AutoSensation]

amzn.to/3y0SryX I had to trim alittle

[@MrJelini]

Hi. when the dimention light or low beam is on, the running turn signal does not work. what to do?

[@AutoSensation]

Does everything else work fine? Does the running turn signal work when low beam is off?

[@MrJelini]

@@AutoSensation Yes everything else work fine! Yes running turn signal work when low beam is off!

[@AutoSensation]

@@MrJelini I'm not sure. What kind of vehicle? Are your turn signals switchbacks?

[@MrJelini]

@@AutoSensation Vw passat b5.5 turn signal works well, but dont work whith dimention lights - l mean led running turn signal.

[@harrysukdevsharma4650]

Hey budd, can you slice the turn signal wire and connect it ? is it any safe?

[@AutoSensation]

Yes you can. Make sure you use a heat shink tube or liquid electrical tape to waterproof the connection. Then it will be safe.

[@harrysukdevsharma4650]

@@AutoSensation ohh yeaah. 💪 come on now 🏇🏇🏇 thanks dude

[@humanairproducts8502]

Hi Greg, can these lights be wired as turn signal only without DRL connection?

[@AutoSensation]

Yes. Don't wire the red wire. Just the black and yellow wire.

[@humanairproducts8502]

@@AutoSensation thank you! I was confused as other videos said to twist red and yellow together! I will follow your link and try to find the same system here in the UK. Do you have a UK link?

[@ItsTammm]

@@humanairproducts8502hi, did you end up doing this? Because I only want it to be wired up as turn signal too

[@radovanjezo7607]

When i comnect red to + on battery and black to - on batter with yellow on turn signal, it will work without any problem ? Because now I have plugged then on low beam and when i start the car, drl Turned off but turn signal still working

[@michaelramirez2369]

Can i ask you something ? is there a way to test the "LOCK and UNLOCK" door wires of the driver seat ?

[@AutoSensation]

That would be difficult. Nowadays power door locks are connected to a module which is interconnected to all the other locks.

[@michaelramirez2369]

@@AutoSensation ow thanks . i tried to attach a Mirror folding kit to my car but i do not know where the Door Lock wire is 🤣🤣 . too bad maybe i need to see the professional to do it .

[@AutoSensation]

Yeah I would have a professional do it. I was looking into retro fitting mirrors into my car but was way too complicated 😅

[@vanshpatel7755]

What kind of pin did you use to push behind?

[@AutoSensation]

amzn.to/3YmyP44

[@galoregalore]

is this the exact one you used in the video ? trying to clarify

[@AutoSensation]

@@galoregalore Same one but smaller size. i can't find the smaller size anymore.

[@hommadis]

Can I cut it and make it short. 13 cm for custom drl.

[@AutoSensation]

Not sure 13cm.

[@berruchearchille5798]

Great video! Do the lights come on when you put the turn signal?

[@AutoSensation]

Yes.

[@berruchearchille5798]

@@AutoSensation Thank you!

[@ReggieTECH]

Great Video! The lights look really cool!

[@AutoSensation]

Thanks

[@RemingtonDrake-vd3tw]

Can it bend to 90 degree angles

[@AutoSensation]

Yes, depending on how you bend the strip.

[@furul86]

can anyone help, i installed an item like this on my car and one side is brighter than the other, I got it replaced from seller thinking it was faulty but got the same problem again, so I switched the lights over and have noticed its only bright on one side of my car the other side is dim, both inidicator light and the DRL

[@AutoSensation]

Check your voltage. Might not be getting enough power.

[@furul86]

@@AutoSensation but the voltage on the indicator lights fluctuates, when the indicator is on, how will i check the voltage.

[@AutoSensation]

@@furul86 Not sure. My guess is bad connection, low power source, or try the other signal wire if there is more than 1

[@jairokattano692]

Thank you. I will follow your guidelines. Next time cover the plate # there's bad people around always.

[@AutoSensation]

Will do. Thanks for the tip

[@DavidHargis-e9j]

What size are the wire pin connectors used to connect to the turn signal? I can’t find them at Ace hardware and the ones online I can’t tell if there small enough

[@AutoSensation]

The ones online are a little big. I did snip them a little to make it work.

[@DavidHargis-e9j]

@@AutoSensation I was more referring to the width of the pin. I saw the you post links to two different pins that were both different pin widths. One was 1.5mm and the other was .64mm width. I assume the smaller ones?

[@AutoSensation]

@@DavidHargis-e9j Yes. Smaller ones. I still trimmed the width

[@DavidHargis-e9j]

@@AutoSensation got it thank you!

[@enhanceduk4642]

What about cars with canbus error free ?

[@AutoSensation]

Should be fine

[@Em12k]

Do you have wiring schematic of where to wire each one?

[@AutoSensation]

Unfortunately, I do not. I used a voltage meter to determine which wire is the DRL.

[@jerwin0416]

@@AutoSensation do you think i need voltage meter to install this on my accord 02? never did any light installation.

[@AutoSensation]

@@jerwin0416 not necessarily a volt meter. You can use a continuity tester. amzn.to/3dSz4yB You need a way to see which wire corresponds to what. If you can get the wiring diagram that would be good too.

[@eddiesuertefelipe1532]

It looks great but issue with this kind of install is during pressurized car wash. Personnel should be aware of that sticker.

[@AutoSensation]

Yes. With the hood closed it should be fine as it lies in between the hood and the headlight. If you pressure wash with the hood open, then you run the risk of the sticker peeling off.

[@rickeyrick1190]

What happened to the first set from a year ago?

[@AutoSensation]

In my garage. One day I'll put it on my other car. 😁

[@rickeyrick1190]

Did it have any issues with sticking to the car

[@AutoSensation]

For the first time use in the first car. No issues at all. Sticks right on and stays. After removing the adhesive to transfer to another car it is not reusable. I will buy more 3M tape so I can reuse.

[@abh3960]

Unavailable where else what else can I look anybody else have them on Amazon

[@AutoSensation]

m.silverholder.com/product/silverholder-car-led-strip-single-color/ref/23/

[@roelbunao3409]

How about on a 2018 rav4 sir?

[@AutoSensation]

Yes. They are universal.

[@a.9651]

Where did you get the tester?

[@AutoSensation]

It came with one of my dash cam kits. Here is a similar one if interested. amzn.to/3i6yKSB

[@a.9651]

Thank you👍🏼

[@edwincheah836]

can the RDL led lights be turned off when the headlamps are on?

[@AutoSensation]

The DRL will turn on and off with whatever power source you connect to

[@sgtking]

Fire can happen??

[@AutoSensation]

Nope. Not if you wire them correctly

[@sgtking]

@@AutoSensation its good to put one more fuse.

[@AutoSensation]

@@sgtking no necessary put you can if you want.

[@cuivincent9744]

key is how to connect with yellow cord as turn signal, which normally hidden deeper under headlights.

[@jackquarantillo5192]

What does it do for remote start?

[@AutoSensation]

For remote start it default on the sequential turn signals.

[@ebar8233]

Hi Greg! I like your videos..where did you get your push pins?

[@AutoSensation]

Thanks. I can't find the exact ones I got. It was awhile ago. These are similar. amzn.to/3ukgxV8

[@ebar8233]

Thanks!

[@AutoSensation]

@@ebar8233 Anytime.

[@f.onfire]

Esta muy bien pero me encantaria mas encontrar unas tiras led que alumbren muchisimo mas intenso! Si lo comparas con tus leds originales de tu coche, ves que es muy delgado i alumbra bien, pero alumbra poco intenso.. busco tira que alumbre mucho!

[@formbyjim]

Where can you buy these

[@AutoSensation]

amzn.to/3oJXvog

[@rayharmacinski4934]

Don't See a link to the product

[@AutoSensation]

amzn.to/3oJXvog

[@artic-boy]

that looks badass

[@AutoSensation]

Now with this I signal more. Lol

[@pilske20]

My friend the glasses and you 360 light are no match! Maybe place the light higher so that we do not see it in your glasses. Furthermore thanks for the info cool video

[@AutoSensation]

Lol. I know. I've been losing the battle. The stand I got is at its tallest. I guess I'll buy a taller one. 😁 I'm just being lazy

[@jaimelopez7752]

I would like to know the brand of these strip lights?

[@BIGBROTHERiswatchinU]

He did post a link to them in the description.

[@danlinganay5337]

I removed my DLR fuse coz mu led headlights have a noise sound

[@roderickdixon5920]

Where do sign up 4 dis need ASAP

[@AutoSensation]

m.silverholder.com/ref/23/ Coupon Code 10% Use autosensation10

[@cnd_ion]

They are not working properly connected to the light((I Connect to the first position(parking) red and black,and yellow to the side on pozitive) ,when key its turned off,and push hazard or direction, 😗tried to ground,having no power Its a little diferent than my, its just cable, no any attached grip for ground, cables are short and very thin, my car doesn't have DRL lights from factory,no fog Light either

[@NewYorkF150stx]

Thank you!

[@AutoSensation]

Your welcome

[@S1L3NTG4M3R]

thanks

[@bengenesalaba3046]

Boss di ba umiinit yan?? Sa akin kc npakainit tinanggal ko nlng bka masunog pa,, 45 cm yun pru yung isa na 180 cm na isang kulay lng normal lng nmn ang init same lng sila ng tapping

[@manueldooc2758]

No need to use tester just go on the wire coding and you will know the correct wiring.

[@kameshganeshan2894]

He’s not a mechanic for living, I suppose

[@AutoSensation]

Nope

[@marioantonio2096]

The video is nice but incomplete. I put it on my car (Audi A6) and although it has daylight, I wanted to make it more interesting. BUT surprise. If you leave more light on the hazard light, it goes out of sync and looks awful. If you have passed this phase, please make a video and teach us too. Success.

[@effectedpringle1420]

Did you wire it to the normal drl?

[@mosween6278]

Nice

[@AutoSensation]

Thanks

[@Novadababy]

How your car get so clean under the hood lol

[@AutoSensation]

I wash it every time I wash my car. kzbin.info/www/bejne/qqTCpIKsga5md8U

[@dokesz530]

buy cob leds.

[@AutoSensation]

I'll see if I can get my hands on some

[@Ukrainianification]

This cheapens the look of a car honestly.

[@immortalconfigurationprodu2937]

What type of push pin did you use?

[@AutoSensation]

amzn.to/459r3yU

[@babbag4667]

Can I tap into the DRL fuse inside under the dash?

[@AutoSensation]

Yes. I believe you can. Make sure that the fuse source turns off when the vehicle is off.