LEXUS/TOYOTA REFLASH/DATA INITIALIZATION IC900 93C56 (KC501+x100 PAD3 SE)

[@scottjohnson9102]

By doing your procedure did it close out the programming? Didn't see info for second key add.

[@VFVT101]

Thank you for your instructions, i just followed along with my xtool pad3 and the kc501. I am putting the ECU Back together and will try this process in the morning to initialize the new key for the customer.

[@jamesbarratt593]

Ok so I have a body control module UCH in my van which I think is faulty. My van is a vivaro 2004. So I have a used one from Ebay which needs coding and after a quick search a forum thread two people spoke about 93c66. Presuming this to be the chip. I recognised that number. Can Autel extract the data from it? Close magnifying of the board I cant read that number on any though. What to do mate?

[@MYKEYSAUTOMOTIVE]

Possibly under eeprom .. ill check tommorow morning!! Its 1:21am right now in California

[@jamesbarratt593]

@@MYKEYSAUTOMOTIVE done the job. Obdstar all the way. Im608 could not even read one chip

[@jamesbarratt593]

🍟

[@parraent.9628]

I’m trying to understand the reason to read eprom only. Does reading it automatically enable you to manually add the key using the open close door procedure? I don’t have to write anything back to the ecu?

[@MYKEYSAUTOMOTIVE]

Hello greetings 👋🏽 Friend! for priority commenting please join our members club! once you join you will also be entered to win for our monthly giveaway! If you want to join ,you can join from a laptop or computer next to the subscribe button you will see the join button!! thank you!🙏🏼❤️

[@StrelkosChopShop]

Does the tool you used in the video have the ability to reprogram the VIN number/mileage on to a new ECM via the Eprom adapter? Also, I noticed in the video you were programming what you referred to as an IS300 ECM however the 1mzfe is the Es300, I only bring this up because you selected IS300 on the tool for your video but then installed the ECM on an ES300 and it was programmed, how did that work?

[@MYKEYSAUTOMOTIVE]

I only reply to members my apologies.

[@StrelkosChopShop]

LOL whatever dude.

[@mechaniac9194]

After Data initialization when you have to synchronize the key in the car, is it the same procedure on a 2000 Lexus gs300? Thanks Mike

[@MYKEYSAUTOMOTIVE]

Yes it is!!

[@mechaniac9194]

@@MYKEYSAUTOMOTIVE Tried this same exact procedure on the 2000 lexus gs300. Car starts right up however the immobilizer light stays flashing even if the car is on. Other than that the car has been starting up with no issues.

[@MYKEYSAUTOMOTIVE]

@mechaniac9194 it’s just telling you that it needs a second key programmed .. so in order for that light to turn off must program a second key to the vehicle

[@mechaniac9194]

@@MYKEYSAUTOMOTIVE thanks for the advice. Besides the immobilizer light flashing will it cause any other issues until the second key gets programmed?

[@AhmedIbrahim-iw6zr]

It shows connection fails do you think the cable is fualty because I didn't get the message when I hook up the kc501 to the pad

[@MYKEYSAUTOMOTIVE]

Hello greetings please join our members club for priority commenting!! Thank you! ❤️🙏🏼

[@calholli]

So why did the computer need to be reflashed? Is that a new ECM? Or did you just lose all the keys? and did you have to bring your own eeprom codes, or did the scan tool already know what to reflash it with? I'm trying to buy a new scan tool, and I don't know if I should buy the xtool pad3 or the xtool D8. They seem very similar.

[@MYKEYSAUTOMOTIVE]

👋🏽 greetings friend! For priority commenting please join our members only club! From a desk top or laptop next to the subscribe button you will see the join button! Thank you🙏🏼

[@cherryred1732]

Is it always best to desolder the chip off the board before connecting the clip to do eeprom reading. As doing some in circuit will corrupt the information on chip . Then it's useless a reading all f or 0.

[@boydlittou9446]

Not a problem doing this in circuit with the AR 32 labs programer.

[@christophercuapio8751]

Que pasa si después de hacer el reflash el foco del security sigue parpadeando? Al igual estuviera genial si enseñaría hacer este proceso con el vvdi prog

[@persysworld7230]

Awesome videos like always. Got a problem with an 08 Camry hybrid. Backed up immo generated analog key. Says learning succeed but when going to read keys no keys are stored

[@MYKEYSAUTOMOTIVE]

you probably have the wrong key ..what programmer are you using?

[@austinoharra1463]

I just purchased the Autel IM508 and am going to the local Pick a Part to pull some ECUs and practice. I noticed on another video with a Sequoia, you had to pull the chip off the board to eeprom it. Is the Sequoia the only one you have to do that or are there others?

[@MYKEYSAUTOMOTIVE]

Hello 👋🏽 thank yo for watching! Make sure you join our members only group for priority commenting! From a desk top or laptop next to the subscribe button is the join button! Thank you🙏🏼🙏🏼❤️❤️

[@dtandfam8100]

Awesome video. Just curious if you've done this using the im608? If so was the process similar? Thanks again for sharing!

[@ming41160]

Yes, it is similar.

[@songse01]

Hi, Mike, I need your help.2022 Lexus RX350 all key lost situation and I tried to program a key with a local locksmith and he couldn't do it. I have IM608 and I don't know how to get EEPROM. It seems that the immobilizer module(Lexus called I.D box) is located deepest inside the dashboard behind the heater box. Is there any different way that I can try?

[@MYKEYSAUTOMOTIVE]

Hello greetings friend! 👋🏽 for priority commenting please join our members only club! Thank you!!🙏🏼❤️

[@iskooobydoo]

Hey Mikey..how do you this on a Im508? I don’t see a ‘initialize’ option. Only read, write, erase, set. Would it be ‘erase’?

[@MYKEYSAUTOMOTIVE]

initialize is not capable on the im508 sorry

[@335135]

I saw u had a video on a sequoia all keys lost that was also 4c and u did a reset with the autopro pad can u not do the same or is it just cuz it’s a different immo system

[@Cali415]

My brother! Do you know if you can do this same procedure with vvdi mini prog/ Key tool max?

[@dashtyATG]

Hy Mike long time, Hope you ok. Mike when using old ECU do you have to verginz the old ECU before you write the old ECU IMMO data or you can just read old IMMO data and write it to a used ecu? Hope you understand.

[@antoniosaldana8947]

Hi, I did a 2003 Toyota Highlander with all keys lost, I generated a key by cylinder door and I was able to program it without a master key.. I used my Ikey820 and I did the onboard programming, it worked. How is that even possible.

[@335135]

I was able to do the same on a 2003 Toyota Sequoia and a 2002 Toyota Camry I’ve noticed Toyota and Lexus even tho they are the same manufacturer Toyota is easier

[@mooresautorepair8370]

thankyou for your videos , i am just getting started in automotive locksmithing. Do you reccommend and training books or online training. I am currently a auto repair technician looking to transition due to health

[@MYKEYSAUTOMOTIVE]

hello greetings member! I teach hands on classes here in california! where do you live?

[@mooresautorepair8370]

@@MYKEYSAUTOMOTIVE kansas

[@MYKEYSAUTOMOTIVE]

i recommend you just go through all my videos u will learn alot! start with the key too max videos learning how to clone keys!

[@mooresautorepair8370]

@@MYKEYSAUTOMOTIVE Thank you. Keep up the good work

[@emmanuelakande8263]

@@MYKEYSAUTOMOTIVE how can I enrol in your classes. I have completed my basic classes in locksmithing at acme and I am specializing on auto locksmithing. How much and how many weeks is the training. I can fly in from chicago to California for the training.

[@groove2064]

Hi mike am i able to remapp my ecu on my Lexus rx450h by using techstream I would like to eable the i want

[@MYKEYSAUTOMOTIVE]

Hello friend! 👋🏽Please join our members club for priority commenting and a chance to win in our monthly giveaway! You can only join From a desktop or a laptop next to the subscribe button. Thanks!🙏🏼❤️

[@dashtyATG]

Hy Mike just about to go for 1 it's Toyota Corolla 2001 4C but I'm using IM508 use xp400 would it be the same process please?

[@MYKEYSAUTOMOTIVE]

Im afraid not ! You will need to read key data ,save file.. write key via dump and write back to chip!

[@abuujulaybiib4884]

Hi brother. Hlp please. what is the best key programming machine between autel im 508 full package and xtool pad 3 full package ?

[@sheilakay5068]

hi Mike, thanks for sharing your knowledge with us. how do you know the correct chip to locate if at all you do not know the ic number?

[@MYKEYSAUTOMOTIVE]

It will be on the write key via dump page.. also the autel shows you a schematic diagram with the module

[@studio3356]

I am totally new in this keys stuff mt friend. Let me know flashing the eeprom means virgin it I mean when you flash any eeprom There no keys data or something??

[@tonotono2245]

Hi, Can i program Toyota starlet ep91 from 1996 I lost my master key And do you know which chip number mine have?

[@MYKEYSAUTOMOTIVE]

Hello greetings 👋🏽 friend! For priority commenting, join our member club! once you join, you'll also be entered to win our monthly giveaway! If you want to join you can join from a laptop or computer next to the subscribe button you will see the join button! Thank you! 🙏🏼❤️

[@335135]

Is this the same process with autel doing my first one now

[@MYKEYSAUTOMOTIVE]

With autel it's different you have to write key via dump.. load One touch and write back to chip

[@335135]

@@MYKEYSAUTOMOTIVE I spoke to autel technical support and they told me choose the vehicle go to immo demolition read data and save then reset immo once complete program key manually…..it’s a 99 4Runner will the program procedure be the same as this video

[@cechuck1]

@@335135 Was that procedure all done through the OBDII OR ON Bench?

[@335135]

@@cechuck1 bench and obd

[@jrlocksmithservices6832]

Hello sir .....I have a Toyota Highlander 2003.....ic900 is 93c86 write at top. possible can reflash?

[@99726613]

Thanks for the video, I wish you continued success and prosperity. I am one of your students. But I have a question, does this method work for the Lexus LS400?

[@mtyler7807]

Would this be the same for the 2001 es300

[@mtyler7807]

I did a gs300 today and I was expecting to reignitalize the immo chip but the customer had the broke off key. I just popped in a super chip and cloned it and cut it from the passenger door code. And they were up and running.

[@MYKEYSAUTOMOTIVE]

Yes

[@boydlittou9446]

Need to see video doing programming with xtool kc501 on the xtool pc software. Very little out there on the kc501 pc software as it is also a stand alone programmer.

[@carlosautotech6602]

Das clases de programar llaves en línea, me interesa

[@MYKEYSAUTOMOTIVE]

En linea no amigo disculpa solamente en persona!🙏🏻

[@randolldoon]

how about akl toyota 8a chip blade key with im608?

[@pearljameric]

Thanks. I have the KC501 and I have yet to use it. What was the process after you got the file?

[@MYKEYSAUTOMOTIVE]

Hello greetings please join our members club for priority commenting!! Thank you! ❤️🙏🏼

[@danielf1016]

Pudieras hacer un ejemplo igual con autel 608

[@TheNeurotik]

hi mike, awesome vid, always following your progress. i have the same setup, pad 3 elite, kc501 did a few 4C cars so far. Quick question, are all the learning procedures the same? 5 x ign off/on with a 6 x door open/close? On some toyotas, its 5 x ign off/on only. Currently doing a 2003/2004 ES300, would it be the same?

[@MYKEYSAUTOMOTIVE]

Hello greetings friend! 👋🏽 for priority commenting please join our members only club! Thank you!!🙏🏼❤️

[@abiliobaulane5245]

You have files immo system toyota smart key?

[@jamesbarratt593]

What is flashing ecu? Wiping it!

[@MYKEYSAUTOMOTIVE]

Virginizing the chip, bringing it to the new state .. (data initialization)

[@AFRICAINSECRET]

How do get that machine you are using

[@MYKEYSAUTOMOTIVE]

Hello greetings 👋🏽 Friend! for priority commenting please join our members club! once you join you will also be entered to win for our monthly giveaway! If you want to join ,you can join from a laptop or computer next to the subscribe button you will see the join button!! thank you!🙏🏼❤️

[@sumitshridhar8386]

Hi All , Can we do All lost key on Camry Sportivo 2003 4C chip through OBD by Autel by using Reset of immobiliser. I know that for 4D chip we can do , but i was unable to do for 4C chip , some videos on KZbin show people are able to do 4C chip also successfully , but i think not all models , some models yes and some models NO

[@2324E.M.S.]

Yo tengo un w204 MB c300 el EIS esta roto completo, se puede usar uno usando I virginalizarlo para usarlo y ponerle el data del carro yo solo tengo un Im508 y xp400 Soy nuevo en esto ayuda porfavor the eis is brocken complete

[@MYKEYSAUTOMOTIVE]

Se acupa hacer el erase primero del eis .. si no uno nuevo .. y copiar del eis viejo al nuevo

[@yiannakosautomotivekeys2380]

Hi Mike. I learn something else today and thank you for that. What was the reason for initialising the chip? Couldn't you program the key without the initialization, and if you tried to program the key before initializing, what errors were you getting? Great video. You are the boss!!!

[@irshadsau3699]

It's a ALL KEY LOST situation, that's why he had to initialize the eeprom!

[@oscaresquivel8955]

Good question. So in an all keys lost situation if you dont initialize de eeprom you wont be able to program any keys? Does the initialazation modify (verginizes) the eeprom data? What about a simple bridge between pin 4 and 13 of the OBD2 connector with switch on the ON position for 30 minutes would thta get the car running as well?

[@cristianyerena9339]

Y con la IM608 hacer el mismo procedimiento?

[@dynamic6864]

Hi Mate from Downunder very big fan!!! Great content.... .Is it true that you can have current loss with clip in circuit ....or data collision if the power feeds to other circuits and starts them?. ie processor starts up...tries to communicate with eeprom while programmer tries? Also i read 93 family has erase command...and can if data collision triggers erase code its gone? Is it safer to do off board on these??

[@MYKEYSAUTOMOTIVE]

Yes there is alot of risks if you dont know what you are doing

[@bradt9350]

I remember with the early 4C system when using a program like Carprog to zero out preexisting immo values on the chip, you had to de-solder the chip and isolated it for those reasons.. I was surprised to see that the Autel was able to do it without Isolating it.. They must factor in all those things when they write the programmer software now.

[@w3g0tl00t]

Do these units also do odometer corrections ?

[@rajushaikh9045]

Yes u can but u have to write hex numbers

[@gajahlampung5674]

nice job sirr .sir can you help me i replace ecu smartkey toyota fortuner with 93c 86 epprom..now i can't have ignition on..can you help me sir..i'm from indonesia sir

[@vincetan1735]

i sir i cant find the IC900 only the IC902 is it same?

[@MYKEYSAUTOMOTIVE]

Hello greetings 👋🏽 Friend! for priority commenting please join our members club! once you join you will also be entered to win for our monthly giveaway! If you want to join ,you can join from a laptop or computer next to the subscribe button you will see the join button!! thank you!🙏🏼❤️

[@latin01985]

Can I do that on the 98 gs300

[@MYKEYSAUTOMOTIVE]

Yup

[@brianfrey9541]

Your a good teacher man. Thanks for taking the time.

[@MYKEYSAUTOMOTIVE]

thank you glad u liked it!

[@qicpic007]

I use one of my wife’s emery boards to clean the chips

[@MYKEYSAUTOMOTIVE]

☺️☺️☺️😅😅 well done

[@dashtyATG]

Yo yo yo big boss that's what I'm talking about. I always trust u %100 ,very good info shearing what are you man. Can IM508 do that as I've the same eprom reader cable for the 8 leg? God bless you.

[@MYKEYSAUTOMOTIVE]

Theres two chip type clips for toyota and lexus one is a ic dip socket 8pin microchip the other is a SOIC microchip 8 pin.. so u need two different clips

[@MYKEYSAUTOMOTIVE]

Ill explain it on the next video !

[@olumofeadeola243]

Nice job thanks alot, can you upload 2017 Range Rover add with Autopropad thanks.

[@Nery_00]

Se puede hacer con la 508

[@denmarklewis8907]

Bro I think your the best at this would love to learn more from you🙏

[@dennismartinez9112]

Your the best Mikeyss ! Gracias por todo tu tiempo y tus enseñansas !

[@MYKEYSAUTOMOTIVE]

Thank you bro!!

[@335135]

It’s so funny I was doing an all keys lost on a 2002 Toyota Camry 4c and I couldn’t do it so I’m assuming I have to do this

[@MYKEYSAUTOMOTIVE]

Yes sir!

[@335135]

@@MYKEYSAUTOMOTIVE thank u so much is this programmer worth buying or should I just jump straight to the autel because it’s starting to add up I have the xhorse, Topdon ninja, obd star x300

[@mcdlol6]

@@335135 get autel 508 I haven’t touch my xtool pad2 ever since I got my 508 with xp400 it does the reflash as well

[@335135]

@@mcdlol6 is it a quick connect like this or is there soldering involved

[@mcdlol6]

@@335135 just like that one no soldering

[@tyshawnjones247]

Nice it's a pain in the ass to put all thst stuff back together lol

[@MYKEYSAUTOMOTIVE]

☺️☺️☺️

[@saibabupodala6297]

Thank you bro share this information you're doing I'm 608 videos was very nice this time XTOOL you giving lots of information keep going

[@MYKEYSAUTOMOTIVE]

Thank you brother God bless you!

[@amadoudiallo7826]

we call the best techer

[@jamesbarratt593]

Mate you are hilarious you start the video saying about make sure that you don’t put it anywhere near anything that can conduct electricity but whilst you’re doing it you’re completely bare handed so that your skin conducting static electricity can damage the board. You have to be wearing an antistatic wristband and then if you really want gloves. But without an antistatic wristband you’re asking for problems.

[@MYKEYSAUTOMOTIVE]

Heheh 🤭

[@paulsimon5838]

@@MYKEYSAUTOMOTIVE okay

[@28peterpan1]

You’re the best bro, always sharing your knowledge. We learn lots from you. God bless you.

[@MYKEYSAUTOMOTIVE]

Thank you brother!

[@efrainguerra4014]

Thanks bro nice way to explain

[@MYKEYSAUTOMOTIVE]

Thank you brother appreciate it

[@laldhaneesh7923]

Thank you sir♥️🙃😎 Waiting for Toyota New model smart key all key lost 🤗🤗🤗

[@MYKEYSAUTOMOTIVE]

☺️☺️🙏🏼☺️🙏🏼🙏🏼

[@amaniganza1154]

Thanks for your tutorial ,it helps me a lot , but would you help me to make a course that can help to dive into keys programming and ECU repair as someone who is already a mechanic and auto electrician ,Thanks

[@geremiasfernandez6372]

Excelente amigo gracias por su apoyo dios le bendiga

[@MYKEYSAUTOMOTIVE]

Gracias a ti amigo

[@sergizandoval9516]

Como siempre muy comoletos y excellent infomacion gracias

[@MYKEYSAUTOMOTIVE]

Gracias bendiciones!

[@fernandohood5542]

I swear there is a million ways to register keys.

[@amadoudiallo7826]

Thanks so much

[@MYKEYSAUTOMOTIVE]

Thank you!🙏🏼❤️❤️

[@boazorcolebel488]

Thanks for the enlightenment sir

[@MYKEYSAUTOMOTIVE]

Thank you !🙏🏼

[@ankursood89]

Pad elite awesome 👏🏻

[@amandadelacruz499]

Awesome 🤗

[@MYKEYSAUTOMOTIVE]

🙏🏼🙏🏼🙏🏼❤️❤️❤️

[@irshadsau3699]

Thanks Mike 🙏

[@MYKEYSAUTOMOTIVE]

Thank you brother God bless you!

[@harryhoudini7777]

Hi Myke just one question I cant find video , what we can to do if is all keys lost and eeprom immobilizer chip its broken . Is there any way to make new keys?

[@abiliobaulane5245]

Good video my friend

[@MYKEYSAUTOMOTIVE]

Thank you sir

[@DavidGutierrez-zi4dy]

thanks.

[@CRAZY_VIDS07]

My goodness 5min into it and still repeating the same crap... WE KNOW RED LINE IS PIN1 GETTO THE POINT. LETS GO,,LETS GO

[@MYKEYSAUTOMOTIVE]

😅😅😅patience young grass hopper

[@aleksandrogienko3371]

Super

[@M.BilalAutocenter]

I like you

[@MYKEYSAUTOMOTIVE]

🥰🥰🥰

[@M.BilalAutocenter]

Mike Bro Send me your whatsapps number please I like this your

[@ricardogonzalez9448]

Sheeesh

[@MYKEYSAUTOMOTIVE]

Sheeeeeeeessshhhg

[@SILVERBACK086]

Would this be the same for a 2000 Toyota 4Runner? It also has a ic900