Nice build you have. I went with the same combo rods and pistons on my 7mgte I built earlier this year. I am aiming for 500 to 600 whp with e85 running the Sound Performance 6262 bolt-on Percussion Turbo. So far I just finished the engine break in at 1k miles and just put in the BC 264 cams a few days ago. Next I am redoing the engine wiring harness for the ECU Masters standalone this winter.
@-LFATV6 жыл бұрын
Shwalker07 thats sick dude!! The only thing i havent done is cams. And the 264s are the ones i would like to do aswell since you dont have to upgrade valvetrain. Do you happen to have a video of her idling??! And im also gonna be running ecu master, but isnt it plug and play? Why do you need to rewire your harness?
@Shwalker076 жыл бұрын
Those 264 cams made a very nice difference compared to stock and pull way harder from about 3k rpms. Still have to change a few valve shims as some have a higher clearance than the BC spec. Have you heard of running comp 975-12 valve springs? They are from a Chevy v8 but drop right in the 7m and help with valve float at higher boost. Its funny that it's for a v8 but they sell them in 12 packs at summit racing for around $30 because I think so many 7m guys ask for them. Right now I am still on the oem ecu and electronics but the ecu masters kit i bought from DriftMotion is a plug-n-play kit that came with the pigtail for my 87. For me I wanted to freshen up the OEM engine harness with new wiring/connectors, get rid of as many sensors/wiring I do not need, add some sensors such as the e85 content sensor/air intake temp and wire it up for sequential fuel injection. By the time I do all this the plug-n-play adapter is unfortunately almost useless. I made a wiring chart of the pigtail using the OEM ecu pins to the pins of the ecu masters standalone so when I make the new harness they will go to the right pins. What is also nice is the ecu masters standalone comes with 2 new connectors and all the pins you need to make a harness yourself. If I was to do it again I would of just bought the standalone without the pigtail. I'll upload a video on my channel sometime soon before I pull the engine wiring harness.
@-LFATV6 жыл бұрын
Shwalker07 dang dude! I think your build is a bit more intense then mine! But i would also love to follow your process man, so if you make videos id love to see. As far as for me this car was elderly owned so all my plugs and pins are in really good condition. Also my main goal is to get 450-550 on pump gas (91) which i know its possible. That way when Supras In Vegas or Toyota Fest in california or any other major show id love to cruise there and not worry about fuel you know. Hats my goal
@-LFATV6 жыл бұрын
Shwalker07 ohhh and no man i havent herd of those valve springs that is pretty crazy though. My brake setup ill be using Mercedes brembo calipers off a 90s benz and i believe 370z rotors if i remember correct lol its a very cheap upgrade and they are huge brembos 🙌🏼🙌🏼
@Shwalker076 жыл бұрын
Nice man, well you definitely earned a new subscriber and can wait for your next update on your build. I am going to publish my whole build with all my pictures on SupraMania and Supraforums very soon if you are ever over there. For now though I have to catch up on some of your older videos.
@AW_DIY_garage Жыл бұрын
I know this video is old, I just wanted to say I appreciated the walk through the checking of clearances.
@-LFATV Жыл бұрын
Thank you sir
@leebowerman58366 жыл бұрын
You supposed to install bearing dry only lube up crank side of bearing. Could cause you problems.
@-LFATV6 жыл бұрын
Lee Bowerman too late.. shes all complete 😬
@livetogame10666 жыл бұрын
That's a spun bearing waiting to happen
@-LFATV6 жыл бұрын
LiveToGame bearings dont ever stay dry.. they do lubricate with oil??
@overbuiltautomotive12996 жыл бұрын
we can not bleave you all did that wow i pull the pan n clean that no matter what befer i go 7 psi or lance it at all
@-LFATV6 жыл бұрын
overbuilt automotive im sorry brotha but i couldnt understand your message??
@ImReelySuqi5 ай бұрын
From every old Toyota tech i ever knew. They say to use that ring compressor. I believe em
@ChirpStarz8086 жыл бұрын
Cheee yah bro. That block be lookin great. I cant wait to have the same feelin your havin as soon as my block gets back from the shop.
@-LFATV6 жыл бұрын
AKIRE 808 heck yea man!! Its very exciting, cant wait to be driving her by maybe feb or march
@UnsmartCanadian6 жыл бұрын
I like that, "You think they're safe? Ima leave em like that!"
@mitchellhoover30475 жыл бұрын
Now ik how a plasti gauge is used!
@boostjunkie23204 жыл бұрын
How has this engine done over the last year? Thanks for uploading. Looks like you were getting ready for a big turbski!!
@-LFATV4 жыл бұрын
Steven Marzullo engine is still very healthy, although i never really pushed too much power through her. She was last about 400hp new setup will be alot higher
@boostjunkie23204 жыл бұрын
@@-LFATV That's good. Clearly greasing both sides of the bearings didn't give you any problems. I've had 4 MK3 Supras over the year's and I'm starting to get that itch again.
@-LFATV4 жыл бұрын
Steven Marzullo no sir i mean if you think about it oil makes it way through them through the galleys anyway so the grease in our opinion helps them stay lubed during initial start up.. thats the theory
@TheMrFlyBoy18 Жыл бұрын
Great video man and selling my subie to eventually get into a manual mk3 turbo. Your channel has great information. Only thing I suggest is creating playlist for certain things. I was looking for videos on your mk3 on your channel and nit gonna lie, kind of messy and hard to tell which videos connect to each other. Up to you but as a subcriber it makes it easier to navigate all your posted videos. You have hella of them lol. Not hating only suggesting to improve the channel
@marsocreaper5 жыл бұрын
A real car shows up !!!! Evo for live
@-LFATV5 жыл бұрын
marsocreaper i think you meant life... lol
@BjornFSE6 жыл бұрын
loved the detail
@-LFATV6 жыл бұрын
BjornFSE thanks man
@oveidasinclair9826 жыл бұрын
Looks like you had your block re-decked, my dad had to have that done to his 7mgte, he has the pictures of it on his cell phone still. In my Supra I'm not goingt owast any money on the 7m, I'll be istalling a 1JZ at the end of them month when all my parts finally arrive. Good luck with your car.
@-LFATV6 жыл бұрын
Oveida Sinclair thank you man
@j-soulfilms6 жыл бұрын
nice man! Its good you show some details in the block. How about show some of the detail head too.
@-LFATV6 жыл бұрын
Initial JDM thank you man! Im not sure if you check out the next video yet but i made the head assembly video the same
@j-soulfilms6 жыл бұрын
LFATV Yea, I check it already right after I watched your other video lol. keep it up! Love the build though
@-LFATV6 жыл бұрын
Initial JDM haha thanks man 🙌🏼🙌🏼
@chrishanse1005 жыл бұрын
Awesome video, just dropped block at machine shop couple days ago. Looking at the wiseco pistons and eagle rods. You like the 9.0:1 ratio? Are those eagle rods you used? (I have always lubed both sides) great build!
@-LFATV5 жыл бұрын
chris hansen im loving the compression ratio so far, havent gotten it tuned so wel see later for best results. And yes i used eagle rods
@chrishanse1005 жыл бұрын
@@-LFATV super cool, what injectors are you running?
@lockjawjak6 жыл бұрын
I thought you weren't supposed to put lubricant behind the bearings?
@-LFATV6 жыл бұрын
lockjawjak well on initial start up there will be no oil on them whatsoever, so the lubricant put on them is for the first start up. But then again everyone does it different
@sansui19686 жыл бұрын
i make a oil pressurized primer i hook in to the oil tap on block the most elcheapo would be a bug sprayer with oil in it used as a oil gallery primer
@ClimptonDiddlehopper6 жыл бұрын
You shouldn't and don't need to lube between the bearring and block or caps. They don't turn unless they are failing. You use a proper assembly lube (not white grease as it cakes up think of a chapstick consisenty) only on the bearring surface on the crank side. A proper assembly lube is cheap compared to a set of bearring rods or crankshaft. Yes I'm a engine builder from motorcycles to heavy diesel to tug boat diesels as well as performance including my son's Supra 7mgte and 2 non turbo. Also built my turbo first gen neon.
@-LFATV6 жыл бұрын
Billy Beane Got it.. well its been couple months since this video and engine is running perfectly 😀
@pnuema1.6183 жыл бұрын
haha this is the comment I was looking for! Heavy line Diesel mechanic here and the answer is no your not. Assembly lube on the the wear face only. LFATV ~ you get lucky sometimes thats all there is to it. No hate just education. Forged rods aren't better btw.
@czarekaj10982 жыл бұрын
Just out of curiosity, What is the piston ring gap for your application?
@sansui19686 жыл бұрын
cool i know its an inline but i hope ye balanced it gaped rings according to intended boost
@-LFATV6 жыл бұрын
Sansui Mcpeters everything was done properly 🙌🏼
@ClimptonDiddlehopper6 жыл бұрын
With forged piston and rods you are well within spec and weights are done in the factory. You can take one step further and have the entire rotating assembly balanced but it's a waste on a mild build so this will be better than stock and acceptable by any builder of 7m's
@-LFATV6 жыл бұрын
Billy Beane 🙌🏼 Very Knowledgeable! But yes, Mr.Gallardo ( builder ) thought the same and didnt have any worries when it came down to balancing
@mrctuned28446 жыл бұрын
Actually, if you are talking about assembling an engine correctly, you need to balance each piston and connecting rod seperately, usually to .1 grams is sufficient. The entire rotating assembly must then be balanced, on any build, if you want the engine to last as long as OEM. It doesnt cost much, and saves main bearings. Every single set of piston rings I've ever installed has had to be filed to the proper gap.
@-LFATV6 жыл бұрын
MRC Tuned definitely! I was asked on FB aswell if the rings were properly gapped and pistons were balanced. But we dis follow spec as to them being forged pistons, there is a slight difference from the gap on the cast pistons but we got them dialed down. She is currently running beautifully
@ACommenterOnYouTube3 жыл бұрын
11:10 WHO is using a mallot to drop the pistons in ?? If they are, they don't need to be working on an engine. I just got the cheap auto zone piston ring compressor and dropped them in with my fingers the same way you did. As most engine builders have told me the rings need to be compressed from the outside going in at equal distance. Your compressor is a fixed size so you have to use your fingers to compress the rings so that you can slide the compressor over it. It works but i guess everyone has their own method. 12:14 & 13:17 Did you deck the block ?? What are those black spots by the water jacket holes ?? is that the old head gasket material that is still left there ?
@joseluiscruzperez4399 күн бұрын
Como aumentarle los caballos de fuerza aun motor 7m gte mk3
@MARZOSIRUS5 жыл бұрын
That crankshaft looks like it has waterspots
@123thatsithaha6 жыл бұрын
Did you uses any locktite for the crank bolts or the rod bolts?
@-LFATV4 жыл бұрын
tim moua no bro not on the rod bolts
@2012lakers5 жыл бұрын
How much is the cost to have 7mgte rebuilt? Just in parts? I Just picked up here in Phoenix a turbo 89 Supra targa top for 800.00 but has a spun bearing. Would really appreciate an answer.
@adventuresofestto10083 жыл бұрын
Don't know if this could still be relevant, but I'd say around 4000 to 5000+ for a performance build and 3000 to 4000 for a basic rebuild
@overbuiltautomotive12996 жыл бұрын
i bought a micro squirt ecu fer mine
@-LFATV6 жыл бұрын
overbuilt automotive mega squirt right
@hansen21martin5 жыл бұрын
Hi Im currently in the process of disassembling my own 7mgte, and i noticed that i have the same discolouration on the crank next to the bearings. Is this normal? I realize the colouration could just be from the grinding process, i just find it Odd that no further threatment has taken place, im no metallurgist But wouldnt the crank be softer where its been heated?
@-LFATV5 жыл бұрын
Its pretty normal, i would suggest taking it to a good local machine shop and they would determine if it needs any treatment other then a simple polish, mine was fine so all they did was a quick polish and it was good to go
@hansen21martin5 жыл бұрын
@@-LFATV Cheers man 👍great vids btw
@-LFATV5 жыл бұрын
hansen21martin thank you
@andredavis27275 жыл бұрын
Hi my name is Lenny and I have a 1990 Toyota Supra MK3 in trying to do a little bit engine build to it so I have a question did you bigger connecting rods or no
@-LFATV5 жыл бұрын
Andre Davis i have aftermarket forged rods
@andredavis27275 жыл бұрын
@@-LFATV ok so no oversize bearings for the crank
@andredavis27275 жыл бұрын
Im doing a build on my 7mge T as well if you have any pointers or anything I should do for you let me know
@-LFATV5 жыл бұрын
Andre Davis no sir no over sized bearings, i would recommend and aftermarket oil pickup line, new oil pump thats shimmed, metal head gasket with arp equipment. Those to start off with
@andredavis27275 жыл бұрын
@@-LFATV thank you
@davidphillips74736 жыл бұрын
Hi what type of clvite u use and wat hp u making ??
@-LFATV6 жыл бұрын
David Phillips i forgot what clevite bearings i used bro but im still on stock power because im breakin the engine in still
@davidphillips74736 жыл бұрын
@@-LFATV sweet as was just wounding cause looking for ones to use in mine
@floydperkinsjr95896 жыл бұрын
Where is the lex?
@-LFATV6 жыл бұрын
Floyd Perkins Jr i still have her... shes just been neglected lately 😢
@tonyfalcon9543 Жыл бұрын
Where can I order a egr valve for my 1987 supra
@-LFATV Жыл бұрын
Arz performance
@matthewcoffin72923 жыл бұрын
What crank? I can not find one for my car
@-LFATV3 жыл бұрын
its my oem 6m crank
@josephmanna90825 жыл бұрын
No you don't put any assembly Lube underneath the main bearings they do not consist of any moving Parts it has no benefit at all to put assembly Lube under the bearing you put assembly Lube on the bearing not under
@-LFATV5 жыл бұрын
Gotcha, dont think im not taking your advice im just saying that we have been doing it for years on the 7M, might not have any benefit on the bottom side but we always have done it.
@davidanthonytechurnangauta48805 жыл бұрын
Nice work! Anyways whats the background music😅
@josephmanna90825 жыл бұрын
Sorry to say but you do not but lube under the bearings 😂😂😂
@-LFATV5 жыл бұрын
Joseph Manna lube is for initial start, u dont think oil goes there either?? we have been doing that for yeaarrrsss never had a problem but thanks for looking out
@GtaCracker4 жыл бұрын
10:20 i came
@jimhall109511 ай бұрын
Grease between the bearing and block? Please stop!
@-LFATV11 ай бұрын
Still running strong 💪🏼😎
@_i-kr6eg5 жыл бұрын
Wtf you dnt need no fucking spary to install the metal head gasket or even a non metal one .
@transformer889 Жыл бұрын
I wish we had the option to turn off the awful music😠
@-LFATV Жыл бұрын
Mute it
@transformer889 Жыл бұрын
@@-LFATV I love your commentary, I like to listen to you but this constant drum beat driving me crazy.
@-LFATV Жыл бұрын
@@transformer889 lol very old video, luckily i dont add music like that anynore
@transformer889 Жыл бұрын
@@-LFATVThanks, I am also an MKIII ower, I really like your Supra, and I follow your build, I wish you good luck.
@-LFATV Жыл бұрын
@@transformer889 thank you very much sir
@juancamaney35624 жыл бұрын
Putting lube between the block and the bearings is like putting KY jelly between your pipi and a condom ....That's not vary smart
@-LFATV4 жыл бұрын
Juan Camaney shes been running great 🤷🏻♂️ was for initials start up.. people think that remains there through the engines life time
@juancamaney35624 жыл бұрын
@@-LFATV That's cool man .....But now everyone knows to put on a condom first and then put on KY jelly... Anyway great video , good job .
@-LFATV4 жыл бұрын
Juan Camaney im not putting a gun to anybodies head saying this is the way to do it, everyone online has the correct way to go about things. Im simply recording the process in which i took on my build. And thank you for watching.
@juancamaney35624 жыл бұрын
@@-LFATV You're missing the whole point .... I'm not trying to put you down . I just gave everyone a tip ...You can at least say thanks for the tip
@-LFATV4 жыл бұрын
Juan Camaney i appreciate your condom reference, i always tell folks that i appreciate the feedback. Im simply replying and saying that there has been zero issues to us doing that. Especially my buddy that built my engine, has been doing it for yearrsss