Lidl Parkside 4 in 1 Petrol Multitool PBK 4 B3 Review, Part 1 of 3, unboxing

[@enginelover1]

Good unboxing video. Will definitely will be looking forward for part 3 :)

[@BensWorkshop]

Many thanks, you re very kind! I will be filming part 2 shortly and part 2 tomorrow. Many thanks for watching.

[@henrymurawskibigdogrepair]

Ben good luck with your new project nice box opening

[@BensWorkshop]

Cheers. Feels solid enough! Many thanks for watching!

[@turboconqueringmegaeagle9006]

Extra chipper today mate, not in the market for one but always glad to tune into your cheery hello.

[@BensWorkshop]

You are very kind! Many thanks for watching!

[@DavidBeechfieldBrownArt]

I bought one this week and the bottom of the strimmer head came apart as soon as revs were applied. They replaced the head and the same thing happened. The plastic lugs are not strong enough. The line spool can be pulled off without pressing in the clips.

[@BensWorkshop]

I have not had that problem (as you can see from part 3, here: kzbin.info/www/bejne/r6HKfnl_pN5sgrM Could you send pictures of the both sides of the head? In particular I would be interested in the bits that hold them together and the spring. My email address is on my about page. I will be making a video about the head shortly and will try to work out why some fail. Also many thanks for watching! Please like, share and if you like the channel, subscribe!

[@DavidBeechfieldBrownArt]

@@BensWorkshop yes sure. I sent them a video of it pulling apart.

[@BensWorkshop]

Many thanks, I will keep an eye out for it.

[@BensWorkshop]

As you have a google account you could share it via google Drive. My email address is on my about page.

[@BensWorkshop]

I put up my video, which shows which pictures I would like to see, here: kzbin.info/www/bejne/aGKTk62Dr9eKmdk

[@GrumpyTim]

The advantage of searching for burrs by rubbing your finger along the edge, is that you get a red warning indicator when you find a burr - very useful!!!! I'm a bit behind with my viewing Ben, I'll get round to watching part 2 soon - I'll be interested to see how it performs, I always find the dedicated tools tend to work better than the multi versions, but there again most people aren't going to want to pay for 4 tools let alone store them for the 10 months they're not using them. I was given a couple of petrol hedge trimmers and a strimmer a few years ago - all non functional until I'd done a bit of work on them, and in each case they are nicer to use than my combi hedge trimmer/strimmer - but they do take up a whole load of space. Totally agree about wanting them to put the fuel mix embossed into the fuel cap or tank - each year when I get to my stuff I can't remember the mix (the labels have long since fallen off or worn out) and I have to go searching for my notes or the instructions.

[@BensWorkshop]

A it happens the burr ended up as a splinter! I take your point about dedicated tools, but as you say, there's more than one way of looking at it. Many thanks for watching!

[@GrumpyTim]

@@BensWorkshop ouch, splinters are the worst, mine are usually timber, and more specifically plywood splinters under the fingernail, but metal splinters hurt even more. Hope it's now out and didn't cause too much grief.

[@BensWorkshop]

Not worried about the pain, they are just a pain to remove.

[@AliMackMechanical]

I quite like the Parkside stuff Tbf its ok hobby stuff. Its cheap but then it's the old story you get what you pay for 😊

[@BensWorkshop]

Well... Often I find Parkside stuff very good. I particularly like the 20V team stuff. Many thanks for watching!

[@brendacharles1784]

Hi Ben, i have flooded my 4 in 1 multitool how do I unflood it? Initially the engine did turn over then it stopped. Cant get it to work since.

[@BensWorkshop]

How do you think you flooded it? Typically you could take out the spark plug and pull it over a few times to clear it. Dry the plug whilst you are at it and make sure it is clean. Hope that helps. Please like, share and if you like the channel, subscribe!

[@stephenlocker4326]

Which is better the petrol or battery version?

[@BensWorkshop]

Can't say how good this one is because I have not yet used it. (Will be doing that on Saturday). Can't compare either because I don't have a battery version of this or seperate battery tools that do the same job. Many thanks for watching! Please like, share and if you like the channel, subscribe!

[@stephenlocker4326]

@@BensWorkshop ok thanks

[@BensWorkshop]

You are welcome. I am doing a part 2 on things like putting the chain on, lubrication points etc which will hopefully published tomorrow morning followed by using on to be published Sunday.

[@stephenlocker4326]

Awesome. Interested in the weight when hedge cutting and the size of branch it will cut when you get in action.

[@BensWorkshop]

The engine has weight, quite a lot more than my hedge cutter however it is on a harness so you won't really feel that, and the ends do feel light in the hand.

[@leek1975]

What actual size is the engine in cc ?

[@BensWorkshop]

Can't tell you for sure. Someone else said it was 52 CC. It says in the manual that it is 1.97 horse power. There are 3 parts to the review then another part about the strimmer head. Many thanks for watching, please like, share and subscribe!

[@Mrremusakajack]

How many CC??

[@BensWorkshop]

I don't know where I am but it is either 1.5 or 2 HP so is quite powerful. Many thanks for watching, please like, share and if you like the channel, subscribe!

[@LS-td3dz]

I wonder if you can get spares for these Ben?

[@BensWorkshop]

Yes, and in any case some are universal. Many thanks for watching! Don't forget to like and share!

[@LS-td3dz]

@@BensWorkshop I was talking to a chap yesterday who services and repairs lawnmowers and small engines, he was saying how the E10 petrol is wrecking engines. He advised using E5 as a minimum but preferably ethane free fuel, but that is very expensive.

[@BensWorkshop]

It specifically says do not use E10 fuel. I expect it rots all the seals.

[@LS-td3dz]

@@BensWorkshop yes and according to the guy I spoke to it knackers carburetors too.

[@BensWorkshop]

Yes, all the plastic and rubber in those, like the diaphams and needle valve seats.