Citroen C4 Picasso 2008 Engine ABS ESP EPB Gearbox faults... Fault finding and repair.

[@stuart6798]

You legend! Have exactly the same problem on a C4 Grand, just tried wiggling the loom and in and around the fuse box and now the faults have cleared. I need to fix it now, but thanks to your video I know where to find it. Thank you

[@LMAutoRepairs]

That's great! Thank you for watching and for your comment!

[@glenncooley1940]

excelent sir appreciated😀

[@leonlouiswalker]

Thank you for sharing this video. I had the exact same problem on a C4 Grand Picasso 1.6 HDi engine. ESP warning light would come on, ABS warning light and it also said Parking Brake Faulty. I went to get an M.O.T and those warning lights failed it. I then went to an Auto Electrician and he diagnosed: ABS Sensor (£48) needed replacing/fitting (£40) and/or EGR Valve. The ABS supply & Fit including V.A.T £105 (£48 + £40 + V.A.T) If that didn't resolve it, then the next step would be to supply and fit an EGR Valve. The valves range from £110 - £200 and labor is anything from £80+ as it is located in an awkward place. However, if you are lucky and have your own Diagnostic tools you could follow this video and see how you go. If you have an M.O.T due, beware that they will fail you with those Warning Lights. Good luck! :-)

[@LMAutoRepairs]

All true... any if this lights is an MOT failure... Thank you for watching and for your comment!

[@fetehfeteh463]

Thanks

[@stevebuchanan2032]

A few months ago I bought my 1.6 HDI 2008 with 95000 cheaply from seller because of all warning lights to do with brakes, and DPF. Speedo was also not working. Took a chance on it after watching this video. Before tackling possible wiring issue though I thought it best to put into my local mechanic to run a diagnostic in case it turned out to be just a faulty wheel sensor and easy fix. Unfortunately OBD port was non responsive and still is. He was unable to find why even though power from battery is going to it. Decided then to put into main dealer as they were only going to charge me £55. Made them aware of problems and non responsive OBD. After they finished with car, told me that it needed a complete rewiring at a total cost of £4266. Said that wiring was badly corroded throughout, even they their report gave a 100% no problem r for all other functions of the car which they said drove great. They did not bother with OBD as it was pointless following the visual examination of wiring. Needless to say I was not happy with outcome. Told them where to go and that I would sort car out myself and prove them wrong. Since I had nothing to lose I stripped out the battery and the useless tape supposed to protect the wiring. Following the instructions in the video in tracing the wires, particularly the blue one to see if any were exposed or snapped could find nothing obvious..Ater spending almost a whole day and getting nowhere and being miserable I started to put everything back together. Just as I did so the blue wire came apart without effort about 25cm from the fuse. I patched it up. Started car and couldn't believe it when speedo was fully working. Ran car for a few minutes and rechecked wiring. Switched back on and all warning lights disappeared with exception of DPF. Ony driven couple of miles in car since. When I restarted car today, No DPF warning anymore but now I get faulty handbrake and esr. Even though handbrake is fully functional. Any advice to sort this out now and OBD issue would bo appreciated. But for this great video., my car would have only been fit for scrap according to the main dealer. Sorry for making post a bit of a saga but no doubt a lot of other people have been having same issues. Just take the plunge and have go yourself and save yourself a lot of money.

[@LMAutoRepairs]

That's great man... well done! For the obd... As silly as might sound, check all the fuses... If you give me more details I can check where the power to the OBD comes from... You check grounds first though... However, you can still scan the car, some tools can be powered externally, and you will still be able to scan the modules.... Thank you for watching and for your comment!

[@nigelelyons]

Another THANKS from me! Was very reticent to strip loom too much but as it looked in great condition for the first few inches at each end. But right in the middle along the bulkhead behind battery the thin blue wire was corroded and severed internally. A quick insertion of a link between the break and all the errors have gone. Unbelievable! To help others I had had the following faults. ABS Fault, Brake fault, EPS fault, Depollution fault, Handbrake fault, Gearbox fault, Power steering fault. EGS Gearbox would only change using paddles from 1st up to 3rd. To get further I had to accelerate and drop into Neutral and then back into Auto mode to get 5th or 6th. Gearbox changed down fine! Speedo was just 2 dashes. ODB II reader showed lots of CAN bus errors. Blue wire sorted everything apart from Depollution error. Hopefully a reset and few miles will clear it too. MANY MANY THANKS !!!!!

[@LMAutoRepairs]

That's great news! Well done as well... thanks for sharing your experience! And for watching the video... 👍👍👍

[@SteveSingerFowkes]

This the exact same fault I currently have!

[@SteveSingerFowkes]

What link did you use?

[@johnmarsey3312]

Your a legend!! Sorted my mams car after 5 attempts and garage wanted to replace all parts like abs module and shit to find out was a issue with perished wiring rubbing of the back of the battery housing. Thank you brother 🙏

[@LMAutoRepairs]

That's great! 👍👍👍👍 Thank you for watching and for your comment!

[@RomekStanek]

You are amazing. In my C4 GP 2008 the same blue cable was broken. I have managed to solder new one and it works. Thank you 🙏

[@LMAutoRepairs]

😊 That's great! 👍👍👍

[@alankane8686]

Edited. 6th April 2021 Hi Everyone, After trying everything that was obvious from watching endless videos about wheel sensors, Blue wires, corroded connect etc it turned out to be my front Passenger side Wheel Bearing because the Magnetic strip was faulty. I was amazed that this was giving me all the issues ie. Christmas tree lights Abs, Ecs, Auto Gearbox and more. I hope this helps and it was a pretty inexpensive part to fix compared to the warning alternatives 😬 Alan.

[@12CROWN]

Can you please explain which wheel lift or right I have same problem .. regards

[@alankane8686]

@@12CROWN For mine it was the Front left hand side (Passenger on my car). But to be honest it could any wheel, My part was only about €40 to buy and about €50 to fit.

[@alankane8686]

@@12CROWN If you can get someone with a car scanner to run a test it might say what wheel is causing a the issue but not what the actual issue it that is what happened to me.

[@12CROWN]

@@alankane8686 thank you I'm trying. I scanned the car but it's tells only p1507 gearbox faulty

[@alankane8686]

@@12CROWN a seard on that code says an issue with the Air Control Valve. Someone else on another forum had similar to this and replace an air valve and all was good.

[@ShaunieDale]

I've repaired faults in this area too. As the loom runs behind the battery at this point I believe it is due to acidic vapours from the battery leaching through the PVC of the wire and attacking the copper. The battery has a nice cover that guides all the gasses rearwards and over the loom. In my case there was no communications with the ABS unit and the car was reporting EPB problems.

[@LMAutoRepairs]

ShaunieDale Thank you for watching and for your comment!

[@mrgrumpy5116]

you can't beat having seen it before .. saves a lot of time.

[@LMAutoRepairs]

Absolutely! The very first time I came across this issue, too a bit longer...😋 👍👍👍

[@TheHamouda]

thank you for taking time helping me .your top man.knows great ways to fault finding. take care mate.im learning from you.always

[@LMAutoRepairs]

👍👍👍

[@georgebell9917]

Mt C4 Picasso, has started doing this, i have had it in 2 garages they couldnt work out what it was, due to nothing showing on their diagnostics, now armed with this video going to go back and say theres the fault, Brilliant many thanks for doing what 2 garages couldnt.

[@LMAutoRepairs]

george bell Hi Thanks man... hope you get it sorted... 👍

[@thebear8068]

I can’t remember 7 months back never mind 7 years lol. Good job.

[@LMAutoRepairs]

Tony Lanceley Lol... Thank you for watching!

[@steves7973]

Good one, the wiggle test is good for tracking down electric faults. I have a C4 Picasso, but hope I don't have problems like this !

[@LMAutoRepairs]

Steve PalmII Thank you for watching Steve!

[@peterbeswick8233]

thanks for the video, i checked mine and it was good, i had same faults apart from gearbox, checking and clearing faults then rechecking pointed to EGR, which i brought a new one, just plugged it in without fitting, all faults gone

[@LMAutoRepairs]

Peter Beswick Good for you... hope that fixes your issue... Thank you for watching! 👍

[@almirrajkic22]

Dobar video ,svidza mi se i sve pohvale za majstora,pozzz

[@davehumphrey8672]

I have similar problem on 2008 C4 Grand Picasso 1.6D: Parking break works, but wont disengage. Have to flick dash switch and pump break to manually release electronic handbrake, not ideal. 'Hand brake faulty' & 'ABS /EPS warnings' on display. Some mention checking main dealer for possible software updates but Citroen UK want £90 just to drive into dealership, pop bonnet and plug in diagnostic. Will have a look at wiring like you but possibly a faulty EGR valve affecting parking break system. That's a £200 part and £100 to fix.

[@LMAutoRepairs]

Have you scanned the car at all? Thank you for watching!

[@gezdipz5425]

Got this fault on the same model be taking a look tomorrow,thanks for great vid 👌

[@LMAutoRepairs]

☺️ 👍👍👍

[@magid5441]

I hoped if you captured all the processes glade see you every time

[@LMAutoRepairs]

Magid Thank you for watching!

[@carwashnoord6755]

Great Video.Still working on my 2011 C4 with similar problem.Will try this and let you know.

[@LMAutoRepairs]

Boutique The Source Let us know then... Thank you for watching!

[@johnmurdoch8852]

Thank you for video. Just what I was looking for. Cant imagine what CITROEN would charge.

[@LMAutoRepairs]

Me neither... lol Thank you for watching and for your comment!

[@suditaliano]

Planning to get this car and this video came up 😅. Thanks looks like it might happen eventually

[@LMAutoRepairs]

☺️ 👍👍👍

[@VFRRiderFT]

Hey, Thanks for your video and yes I had the same problem unfortunitly I'm not adept enough to carry out the repair myself however a local Auto Electrician has undertaken the task for me. As you have identified in this video and the live stream you did; once the loom was opened there were many wires affected and that needed repairing :-( I'm hoping to collect the car today... Thanks again.

[@LMAutoRepairs]

Sound good! Hope they get it all sorted! Thanks for the feedback!

[@VFRRiderFT]

@@LMAutoRepairs I've just had an update from the Auto Electician and he has identified about 30 of the 60 or so wires as needing repairs, I've never had such a problem before but I guess this isn't the only car this issue affects; he has also identified some arcing dammage to that internel fused distribution board and will be replacing that too. It does make you wonder about all of these car fires with Vauxhall's over the years????

[@LMAutoRepairs]

@@VFRRiderFT Never researched that... but possibly... At least you are getting it repaired... 👍

[@LoadingRetroGames]

Not sure if you are in England ? Can I ask how much it cost? I'm having the same problem but I've been told it could cost a couple of thousand :(

[@Chris_905]

It always seems that its the french cars that has the electrical gremlins so this vid does make alot of sence , nice vid all the same thanks ..

[@LMAutoRepairs]

chris90 Thank you for watching and for your comment!

[@carbonlarge]

Found the fault ??? (maybe) Checked the wiring around battery, nothing bad really !! then the top of battery fuse plate, looking at the thin wires going to the separate fuse panel where you found broken wire... all looked good but corroded, so I thought I'd strip and clean all contacts,,,,,,, the 4 bloody little fuses just fell apart !!! so i have bridged them out for a test....and dash is back to normal , hand brake working .....so now to make a permanent repair..... Thanks for pointing me in the right direction ..

[@LMAutoRepairs]

That's great news! 👍👍👍👍

[@chrisi1909]

Seems very common on these cars, just had one last week, same blue wire that runs to Pin 7 of ABS. Broke at the same place and also the other wires looked funny. I was thinking that it was coming from the battery gasing.

[@LMAutoRepairs]

chrisi1909 It seems a common issue indeed... It is a possibility... Thank you for watching!

[@zjawiskowy]

Hey, i had today the same problem, I will try tomorrow get out battery and see if is the same problem. Few days ago I did had the same problem but after disconnected battery all gone but today back and I looks like is permanently. I let you know if I will find any broken wire. Thank you so much for the best video! !! !!

[@LMAutoRepairs]

🤞 👍👍👍

[@kennyb1155]

Another 1 bites the dust. Great find Luis 👍

[@LMAutoRepairs]

Kenny B Thanks 👍

[@fawadentezar5511]

Wow wonderfull thaaaasnks mr exsactly i have same proplem with my car.. ur the best tacnicer and profitional! I was more then 10 mecanic but no One can fix it....

[@LMAutoRepairs]

Thank you for watching and for your comment! 👍👍👍

[@carbonlarge]

Cheers mate,,,, same sort of problem on mine and handbrake too.... Next job after the 207 BSI / ABS search :-)

[@LMAutoRepairs]

carbonlarge 👍 Thank you for watching!

[@longfieldcommercials]

Well,this could be a big ,massive help,I have same car, it has fault codes,f000 ecu mute on the can, f000 engine fuse box not communicating on the can fault,but I can read some live data from ecu ie throttle peddle position air temp ,so tomorrow big strip down in that area ,thanks for your video,I was going to confirm powers and ground first,but I think your dialogue make sense,ps it has already been to several garages,parts cannon be fired big time,not by me,I’ve purchased from a breaker,it is just to good to break.

[@LMAutoRepairs]

Hope you find the issue! 🤞 Thank you for watching and for your comment!

[@darrenobee2412]

i have that exact same problem at the moment so i will look in this area thanks

[@LMAutoRepairs]

Darren Obee Hope you get it sorted... Thank you for watching!

[@Новостибезкомментариев]

Огромное спасибо за реальную подсказку возможной причины. Даже, не владея английским языком - более, чем понятно. Удачи Вам.

[@goldgaus]

Получилось решить проблему?

[@Иследуймирснами]

@@goldgaus а у вас как было? Просто я сейчас столкнулся с этой проблемой. Правда у меня с4 2011 года но все болячки у них как я понял семейные

[@andrewmacaskill6167]

I've the same issue here, tested all fuses, repaired the same wires as you found. Nothing worked. Now I've the handbrake module apart, removed motor and that works alone. There is power going into the EPB ECU, not sure why handbrake won't work. It had gotten stuck on and I used the unlocking tool. I've checked all cogs in handbrake unit and they seem to be working fine. Any ideas would be greatfully received.

[@LMAutoRepairs]

What codes do you have? Check live data, and see if the motor work with the scan tool...

[@paulo12222]

Had same problem brought it to Citroen it took a hole day to find what was causing it it was a faulty fuse box on top off the battery

[@LMAutoRepairs]

Glad you got it sorted... Thank you for watching and for your comment!

[@donamoskola4761]

Dear LM Auto Repairs, i have a C4 Grand Picasso 1.6HDi Automatic Dieser year 2010. i have the same errors as you, but not permanently.When i travel short distances 1-10 km the errors are no generated, when i travel long distances 10-200 km the lights comes up . When the lights comes up i am driving in highway, i don't stop the car, i continue to drive, but on this moment the gearbox is switched to manual mode. In dispay i dont have A6 (automatic 6) but i have 6 (mean manual 6). If i lower the gears to 3 than i am not able to go up 4,5,6. Looks like emergency mode. I have a look for any malfunction cable but all cables are fine. If i stop the car, switch it OFF, and switch it ON the lights are not comes up, the errors are disappears. The error appears after some km, often more than 10 km. I did an scan with computer and the error that comes up is : 05FF BSI INTERNAL ERROR. Any recommendation what i have to do to fix this issue ? BR Amos

[@LMAutoRepairs]

Hi Providing the code description is correct, and that is the only fault you have, it can be a bad BSI... Try to see if it can be reflashed/updated and go from there... Thank you for watching and for your comment!

[@donamoskola4761]

@@LMAutoRepairs Can i reflash/update BSI by myself ? Is any tool that can do this ?

[@LMAutoRepairs]

I would take it to the dealer... If you want, you can get Diagbox... but will not allow you to have access to the latest updates... and if you only need it once, is probably a not very sensible investment...

[@donamoskola4761]

@@LMAutoRepairs Totally clear , thanks MAN

[@LMAutoRepairs]

@@donamoskola4761 👍

[@supermarketsweeps]

great nemo's do the same but they lose map sensor signal and egr problems , we got customer to repair himself as hole loom was damaged he wouldn't buy a part loom £170 , i think its because they twist wire and bend them round corners , great vid

[@LMAutoRepairs]

supermarketsweeps Thank you for the info... and obviously thank you for watching!

[@allendownie7254]

Good video, hope it helps people save some money. I had exact same issue with my automatic c4 picasso , totally baffled Citroen mechanics.

[@LMAutoRepairs]

Thank you for watching and for your comment! 👍

[@moshedayan3999]

Hello, I have a Citroen C4 Picasso and the fault is that when I change the gear selector on Automatic, it shifts by itself to reverse.

[@LMAutoRepairs]

🤔 Check on live data that when you put it in auto that the gear selector is indeed requesting auto... You can have a bad gear selector... Thank you for watching!

[@mickymadueno6594]

great video and good work I know it is a short video but one of the steps you have had to do. is. See the communication uce of abs and the line can either be with an opcislocope or true polymeter since for this it is safe to remove and check the wiring or well if it was another shorter route in good time greetings from Spain

[@LMAutoRepairs]

Thanks! 👍👍👍

[@xuacu77]

Hola amigo soy de España, tengo ese problema de service, ABS, freno parking....he cambiado la EGR con diagbox y el problema persiste. Puedes darme algo más de ayuda de eso que dices? Muchas gracias estoy negro ya con el...un saludo

[@LMAutoRepairs]

@xuacu77 Have you watched the video?

[@xuacu77]

Yes, I go to try It. Thanks​@@LMAutoRepairs

[@ayyldz6711]

I CHANGED THE BATTERY 15 DAYS BEFORE. Could the battery be the cause of the malfunction? I CHANGED WITH THE SAME MODEL BATTERY.

[@LMAutoRepairs]

Most likely no... but is something was braking up, while changing the battery the wires might have been disturbed, and started to give you the faults...

[@ayyldz6711]

@@LMAutoRepairs You may be right. Because the technician had a bit of trouble while inserting the battery. there may be a break at that time. thanks for everything. You're a good man. :)

[@aaboud123]

Hello, my 2009 Citroen grand Picasso semiautomatic. I get a message "Gearbox faulty" When i move the gear lever, nothing happened, it does not go to "'D" , it stays on "N" and sometimes the car does not start, and other times it starts. The OBD II says "Manufacturer Controlled Transmission. Code P 1834" what do you think the problem is?

[@teetaadla4090]

Hey ,i have same car and today when i get home and stopped ,gear box wont go to Neutral or Reverse ? When i turn off the car it goes to neutral and can start up the car ,now when i drive again and stop ,has same problem ,when turn off car it goes to neutral and again everything works until i stop and try to change r or n ??? And i dont have any messages on dashboard

[@gmills3483]

Amazing! Amazing! I have the same issues. Thanks a million. Tell me, how does one change the dashboard display? My current one doesn't save anything in the memory. I always have to reset date & time. Thank you

[@wandergtb]

Olá. Estou com um Citroen C4 Hatch 2.0 aqui apresentando 12 volts na K-line do Abs e Direção assistida, por isso o câmbio AL4 parou, já revirei o carro todo e não encontrei o motivo. Estou quase cortando os fios da K-Line pino 12 da tomada de diagnóstico e fazendo um ligação "por fora" para ver se resolve.

[@orderofmagnitude-TPATP]

Hello mate i have mk1 pug 3008 abs, egr etc but it wont go past 3rd gear (its auto) - cleared codes. They come back, tried wiggling loom wire. Does not seem to do anything.

[@MrAndrjuha]

Hmm..I have Peugeot 3008 2011 after changing oil in gearbox and place battery back in place i got similar errors as (Electric parking brake fault , Gearbox fault , abs fault ) and so on....I assume that could be place to look first.

[@LMAutoRepairs]

I would guess so... Specially if all started after the area was distributed... Obviously, do check the basics first... connections etc... 👍👍

[@MrAndrjuha]

@@LMAutoRepairs All started after removing battery and tray, because i changed gearbox oil.

[@lukimalin]

hello! Is it possible that the P1739 error I am experiencing is due to damage to this wiring harness? /C4 Picasso 1.6 HDI MCP gearbox /Thanks for answear

[@LMAutoRepairs]

It is possible... but difficult to tell without proper diagnosing... Thank you for watching!

[@sargblue820]

Liked n subscribed ok great video have same problems done check on wire loom all ok pressure break switch changed. On live data says breaking pressure is 125 bar a rest position is this the fault aswell I've run the abs moter and it activate.... please any help helpful many thanks

[@nevzatkayhan5278]

Thanks to the video you provided, I also solved the same problem. Thank you. but my car's rear suspension needs to be calibrated. I don't know the height, in millimeters ( H1M - R1 ) Can you help? Citroen C4 Grand Picasso 2008-modell thank you.

[@nikolarakic4749]

Thank you for this video. I have c4 picasso 2009,2.0 hdi automatic, gearbox fault occasionally, so I cant reverse or use M, gearbox itself works flawlessly, except when sometimes gives a faulty gearbox error. I will check wires, do you know which one would be for gearbox ad how did you manage to replace the wire? Did you replaced small part of it, or entire one and how ?

[@LMAutoRepairs]

Hi I have only repaired the damaged section... there is a link in the description on how I do repair wires... But, have you scanned the car? Thank you for watching!

[@nikolarakic4749]

@@LMAutoRepairs car has been scanned, there are no errors

[@nikolarakic4749]

@@LMAutoRepairs will it be noticeable that wire is damaged? Cut open and simular? At this point, hardest thing is to pinpoint exact wire

[@LMAutoRepairs]

@@nikolarakic4749 You can do that... damage will be visible... It is strange that the gearbox triggers the lights and does not store any codes... What a about live data?

[@nikolarakic4749]

@@LMAutoRepairs i will check live data, i read on internet that problem usually is solved by changing brake switch below a brake pedal. I believe that gearbox itself is good, is just some tiny wire/switch problem

[@DavideMenegalli]

Exactly same faults on my Peugeot 307 !! i'll check the harness loom, thanks !!

[@LMAutoRepairs]

🤞 Hope you find the issue! Thank you for watching and for your comment!

[@mohamadmirza31]

Hello, I have a cetarwen c4 picaso. Do I need to change the gearbox oil, knowing that it is written in the maintenance book that it does not change, but if I replace it is it better for the gearbox or it gets worse?

[@AndersMagnusOlsen]

Fantastic, Saved my year, or rather my car :)

[@LMAutoRepairs]

That's great! Thank you for watching and for your comment!

[@allanriches9381]

Great video

[@LMAutoRepairs]

Thanks! 👍👍👍

[@hashirnawaz4532]

Hey why don’t Come your new video. I want ask about code came in my car u1219 Citroen c4 Picasso patrol 1.8 can you what is the problem with Parkering break.

[@ALImohammed-jd1xe]

Great finding, and thank you so much for sharing. Very Good job mate.

[@LMAutoRepairs]

ALI mohammed Thank you for watching and for your comment!

[@ta.tar.8125]

I don't think it's only modern citroens you just haven't incounterd other brands with this lots of Electronics

[@LMAutoRepairs]

Ta. Tariku That's true as well... But the quality of the materials used, can make all the difference... Thank you for watching and for your comment!

[@xuacu77]

Perdona amigo, cuando haces búsqueda global en diagbox..no te da también fallos de egr? Gracias. O solo de abs.?

[@xuacu77]

La he cambiado y sigue el problema. Voy a mirar eso de la batería pero quería saber eso, si te arrojó fallos de EGR en diagbox.

[@nevzatkayhan5278]

Hello, I have a Citroen C4 Grand Picasso 2008 model. Can you tell me how many millimeters the rear suspension height should be? Thanks for your help H1M-R1

[@-UmarKhan]

Hi, I have a 2013 Citroen c4 1.6 hdi semi automatic, ESP/ASR fault , Power steering ecu data invalid any ideas what it could be drives perfect no issues just those two lights on

[@-UmarKhan]

My rear brake light the middle one is not working will be changing that doubt that will put the two lights on dash

[@LMAutoRepairs]

Check live data also... might give you some clues about what the issue is... 👍👍👍

[@stramazzo26]

Buonasera stesso problema cambiato interruttore ma nulla in piu ho sempre le luci dello stop accese come devo fare grazie

[@grahamtranter3431]

Hi I’m having a similar problem I had fault code c1396 and replaced the clutch pedal sensor now few days later I’m getting fault code c139f the fault in diagbox says short to positive short to earth or open circuit from the clutch pedal could this be a break in the wire where your showing Thanks

[@LMAutoRepairs]

Possibly... Difficult to say without checking diagrams...

[@khaledrahman8087]

Hi my a gear doesn't select it shows gear 1 and I have to use paddle shift to change gears and I only have gear 1 2 and 3 what can be the problem with my car

[@LMAutoRepairs]

Difficult to say... Scan the car, check live data and go from there... Thank you for watching!

[@gee3770]

May I ask if the blue wire is split in few places and I need to replace it , what amp should the replacement wire be? Thanks again

[@evilelf5967]

exactly whats happening with mine,goes fine in manual mode when driving,cuts out and dies instantly,all manner of faults,gearbox faulty,abs,oils pressure....always thought it was a rubbing wire and not mechanical.

[@olehansen6655]

What did u do? I have those alerts on mine c4 to

[@carterjameson6242]

Was the fault draining the battery as well as my battery is draining but it has got all the same faults

[@LMAutoRepairs]

Don't think is this case the battery was draining... but to be fair, you can get all sort of issues when you have this problem... so might be that as well... Thank you for watching and for your comment!

[@shaunwake9200]

hi do you know the correct wire to use to replace this? i have found the damaged blue wire

[@LMAutoRepairs]

Just something similar... If is a can wire, try to keep the twist... 👍👍👍

[@shaunwake9200]

thanks seems theres 3 or 4 with corrosion i have found hopefuffy this sorts it..appreciate the prompt reply 👍

[@wandergtb]

Em algumas literaturas informa que, na K-line não deve haver voltagem, e em outras já que deve haver 12 volts, e caindo para zero volts, e retornando a 12 quando há comunicação entre o módulo e scanner. Estou aqui na dúvida. Qual informação está correta. O veículo apresenta o código de defeito c1208, "Informação de velocidade do veículo em curto-circuito 12 volts ou desligada". Apanhando muito aqui.

[@LMAutoRepairs]

Verifica com o osciloscopio...

[@SlagwerkdocentNl]

Is it possible, to check there is a broken wire in the ABS, when you use a extern 12V on the ABS to check?

[@LMAutoRepairs]

Yes... you can do that... Just be careful to not short anything... Thank you for watching and for your comment!

[@SlagwerkdocentNl]

Thank you?

[@LMAutoRepairs]

@@SlagwerkdocentNl Ok? 🤔😉

[@cristiandalleave6305]

Hello. What about replacing the whole wires assembly? It would be a clean job and would allow to avoid surprises like other hidden damaged wires.. is it so expensive to replace the whole piece? Only connectors to clip isn't it? I just now have the same problem and I think that a full replacement with a clever protection to prevent the new wires being damaged by the battery gases would be a good solution.. Is it really so expensive?

[@LMAutoRepairs]

If you do it yourself is is probably cheaper, still, if you but the entire loom will not be cheap... unless you go used, and get it from a scrap yard or something... 👍👍👍

[@cristiandalleave6305]

Thank you. I am thinking about that because looking at the wires there, they look like they were 80 y.o. .. I have never seen wires with such a bad look neither in Hot Water High pressure washers of 40 years old. Thank you. You are a good man and make good videos .. really divulgative and educative. God bless you!!!

[@LMAutoRepairs]

☺️ 👍👍👍

[@whitepulsarrbeli1309]

Hey mister your videos are very good and helpful i have 1 question i have automatick 2.0 16 v petrol grand picasso car was on automatick brake and i start moving but brake not let go now i have have milion mistakes gear box fault brake fault abs eps fault i can drive car only if i manuely change shifts we clr all mistakes but 2 left says left abs sensor not working and parking brake not working so my question is if i change abs sensor what u think its problem be resolved i mean is there conection betven sensor and parking brake? Thx in advance

[@LMAutoRepairs]

Yes... they are interlinked... Now, as for changing the sensor, make sure there is no other issues, like wiring problems before changing the sensor... otherwise you might change it, and the problem does not goes away... Thank you for watching!

[@whitepulsarrbeli1309]

@@LMAutoRepairs thx Mr.for answer

[@whitepulsarrbeli1309]

@@LMAutoRepairs i resolved problem it was abs sensor everthing is ok now

[@LMAutoRepairs]

👍👍👍

[@sadikmamoun2847]

best tip of the day man thanks for the video

[@LMAutoRepairs]

sadik mamoun Thank you for watching Sadik!

[@stuartcook1972]

Hi, my 2007 C4P has just started with all this and i suspect i am going to cut the loom in the morning and find likewise ( i hope as it has been a nightmare trying to chase the fault until i stumbled on this) . my question , as i am building the loom back up what wire did you use to restore the loom with so i can get some ready for this rebuild. all help appreciated and thanks again

[@LMAutoRepairs]

I used wire from old looms... Just make sure you use the same thickness... Thank you for watching and for your comment!

[@richardguile2954]

Hi my Citroen c4 Picasso 2008 cars depollution came on a few weeks back and now it goes into Limp mode on 3000 revs it was misfiring so I changed the coil and spark plugs but it still goes into Limp mode have you any ideas please

[@LMAutoRepairs]

Have you scanned the car? Thank you for watching!

[@beckygreenwood572]

Hi, I have this problem with my car now. The handbrake is stuck on and abs/esp service lights flashing. I have a fault code of U1213. Do you know what that is? I am on my own with 2 kids and not much money. How would I fix it myself please?? Thankyou for the video.

[@LMAutoRepairs]

I showed it on the video what the problem was (in this case) and how to resolve it... There is not much more I can do... 🤷‍♂️ Thank you for watching!

[@dlugas251]

Good job as always.

[@LMAutoRepairs]

dlugas251 Hi Thank you for watching and for your comment!

[@michalukasz1660]

Any idea which wires are for the transmission signal ? I have a permanent fault transmission signal short to +, or broken ciruit.

[@MrLeofezollari]

Hi Mister . Where is located the ABS module on C4 Grand Picasso 1.6 hdi diesel, Automat, year 2010 ?

[@LMAutoRepairs]

Hi Usually, left hand side front wheel arch... Thank you for watching!

[@paulhenderson9585]

I’ve got handbrake error diagbox says no coherence to the clutch sensor I’ve looked all over the wiring an carnt find nowt wrong do you know where the wiring for the clutch sensor goes too and I’ll bypass it ?c4 gp 2008 VTR+

[@grahamtranter3431]

paul HENDERSON i am having the same issue if you find out how to bypass the clutch switch let me know

[@paulhenderson9585]

There’s 2 clutch switches if your Cruz control stil works that eliminates one of them the other sensor goes to the suspension pump under the wheel arch,still not fixed mine

[@vedranbc]

Can this also be a problem with my citroen c5, 1.6 semi automatic transmition. Every now and then I get gearbox fault repair needed error, and after that error I can't put in any gear onlu in neutral, and when car is cooled down there are no more that error and everything works fine. Thanks a lot.

[@LMAutoRepairs]

Difficult to tell without checking... but if it is heat related, you might be into something...😉 Thank you for watching!

[@kirosimonovski6833]

Ej zdravo druze. Kod mene isto. Citroen C4 1.6 semi automatic, isto pokazuje kad startujem motor. Primetio sam da samo u ljetni period ne mogu da ubacim vise od trecu brzinu, ja imam onu verziju sa F1 komande na volan. To se samo desava kad je napolju vise od 30tak stupnjeva. Samo stanes, ugasis motor i opet startujes. I auto vozi. Znam da nije rjesenje, ali ipak pomaze. Inace mozemo i razmenjivati iskustva zajedno, imamo tako reci isti auto. Pozdrav.

[@nigelcarter7740]

Very well done 👍👏

[@LMAutoRepairs]

Thanks! 👍👍👍

[@nigelcarter7740]

@@LMAutoRepairs this will help as my mates car has this same problem. I’ve got to figure out why the OBD port has no power to it first 🙄 that’s my job for today. Great wrk 👍

[@LMAutoRepairs]

Check fuses top of the battery... not just the fuses, but the wiring also...😉 👍👍👍

[@nigelcarter7740]

@@LMAutoRepairs hi ! Planned to look at car today but it’s pissing down, will look Thursday.. I did look at the battery fuses but they looked ok.. I’ll clean the block and install new fuses see if that works.. thanks for your advice 😎

[@LMAutoRepairs]

Same here... all my plans for today are out of the window...🌧 😓

[@sublimecleaningservices1696]

Great video! Thank you. I have a C4 Grand Picasso 2009 2.0 Diesel. The car has a ESP warning light, Engine light and parking fault. Those lights appear after the Engine is running for 10 minutes, the acceleration go up and dow and the Engine starts with more noise that's normally does. The scanner show the fuel pressure rail. Do you believe that should be the problem?

[@LMAutoRepairs]

A poor running of the engine, can trigger the ESP... and there is no control over the engine/torque due to the engine issues.. . Sort the engine first.... Thank you for watching and for your comment!

[@marcin2303]

Hi, do you think that could causing more other problems? Like On mine c4 picasso 2.0 hdi fault is "fuel pressure regulation electrovalve", but engine does not start after change the regulator :/

[@LMAutoRepairs]

Possibly... Check wiring from the valve to the ECU... Thank you for watching and for your comment!

[@luismiguelrsilva]

Olá Luis Mateus. Parabéns pelo vídeo e pelo trabalho! Mais um seguidor garantido pela qualidade do conteúdo. Gostava de pedir ajuda sobre um erro que penso pode estar relacionado com o conteúdo deste vídeo! Tenho um DS4 de 2014 e acontece que neste momento regista o erro P1716 "Malfunction in the gear lever. Malfunction of the power line or poor contact of the device with the network. " O que acontece ao carro é que por vezes fica como "Auto" a piscar no quadrante e deixa de engrenar a marcha atrás, por vezes regista erro na caixa de velocidades e por vezes recusa-se até a pegar. Por vezes regista erro no ASR/ESP bem como até já registou erro no sensor do pedal do travão. Já foi substituído o comando da manete de mudanças e contínua a persistir apenas o erro P1716. Qunado acontece de o Auto estar a piscar consigo arrancar normalmente e passado uns kms o "Auto" deixa de piscar e a situação normaliza. No entanto acontece por vezes que desligo o carro e quando volto a ligar até aparece o erro de caixa e o carro nem pega. Tudo é e parece muito aleatório!!!! Alguma ideia ou experiência com este erro em concreto? Poderá ser um mau contacto ou fio meio partido que esteja a fazer mau contacto? Gostaria de ter uma opinião e desde já agradeço a possível ajuda? Obrigado e força no canal e no trabalho!

[@LMAutoRepairs]

Olá! Não, acho que ainda não encontrei esse problema... Pode ser mau contacto algures, um fio a partir... ou algo parecido... Se tiveres um osciloscópio, vê a rede em diferentes pontos quando o problema acontece... vê também se consegues comunicar com todos os módulos quando isso acontece... 👍👍👍

[@anthonylonican3180]

Hi I have the Citroen c4 picasso 2008, it came up electrical fault, the starter won't try to start and the inside dash fan won't work, it was driving ok until today, I tried the circuit board on top of battery and checked the fuses, any help please, thanks Anthony from Ireland 🇮🇪

[@anthonylonican3180]

Update, my problem was the earth wire bad connection, so good idea to check it first with jump leads, attach one to the battery earth and the other end to the exhaust, no need to attach the live wire, also if no success try jumping it of another battery, I went through all the circuit boards but I had no tester, so I went old school, everything works grand now, just need to do brakes for test and hopefully all will go well 😀 💚🤍🧡

[@LMAutoRepairs]

Somehow I missed your first post... Anyway, great find! 👍👍👍

[@JeffreyAtkinson-tf9je]

Would u change the wires on other citroen grand c4 as a job

[@LMAutoRepairs]

😊

[@farukhnawaz4071]

Hej sir how fix ABS breaking system faulty on Citroen c4 grand Picasso 2006 1.8 petrol many time come and if lock with key so no fault but may be come after 2 day again

[@LMAutoRepairs]

Scan the car and go from there.... Thank you for watching!

[@fatihkasapp]

Good job. Congratulations.

[@LMAutoRepairs]

Thanks!

[@CarsExposed]

Another great video mate... I was just wondering how much a Citroen dealer would charge for the job ... in my experience they would change ECU, looms, etc to get rid of the problem costing thousands of pounds. What’s the car year and mileage ? Cheers

[@LMAutoRepairs]

Cars Exposed Hi The car year is on the title of the video, the mileage you can see it throughout the video... You are not paying attention... 😉 Lol Thank you for watching!

[@LMAutoRepairs]

Cars Exposed Not sure how much dealer would charge... I know that the one I had years ago, came to me after the owner spent about £300 at the dealer, and some more on a few garages...

[@CarsExposed]

Oops oh yeah 🤪 🤣🤣 cheers

[@michaelknight8149]

Cars Exposed I had a similar problem Citroen told me wiring loom was rusty and had spread to fuse box due to me washing the car and would cost over £2000 to fix the car was only on 39000 miles they said its a common fault and refused to repair it even with there warranty which I had said it was water transgress due to me washing the car I wrote a letter to the Citroen head chairman and got In touch with the BBC Citroen then called me bak said we will replace whole loom and fuse box for me and I must contribute £650 which I accepted they also recalled a few who had same problem offerd them same deal i still have car which is fine now but have replaced air suspension with steel springs car still runs fine it did take them 4 months to fix but gave me a hire car 7 seater which they paid for but I did have to sighn a document to say they did it out of good faith think that was for legal reasons it was a 2 month battle I did ask will this happen again they replied we can't say no for sure

[@shlakser]

Thank you my friend.

[@LMAutoRepairs]

👍👍👍

[@1942Grampz]

Hi, and great video, I had very similar, and loom wires were bared lower down where yours were, Something rubbing on them with engine vibration, had worn through to the wires, shorting them together. Always good to check. Can you tell me which fault code machine you are using. I can't find a cheapy compatible for my Citroen C4GP 2007 1.,6HDi? Thanks a lot.

[@LMAutoRepairs]

Owen Baldwin Hi The machine I am using is a bit expensive just to have as a OBD reader... You better off getting a DS150 or similar... Thank you for watching and for your comment!

[@dami328]

Hi I have same problem I got all the lights coming up but when I drive the car it won’t go on 4th gear is it might be the problem . Or I got the problem with gear box

[@LMAutoRepairs]

Difficult to say... you need to investigate... Start by scanning the car... Thank you for watching!

[@dami328]

LM Auto Repairs is that problem you had on here did the Citroen was driving fine ? Or you had some problem as well

[@LMAutoRepairs]

@@dami328 As explained on the video... not sure about the driving... as I have not drive it...

[@christineoatley4650]

We have checked the loom and there are no broken wires so do you have any ideas what else it might be? The problem is exactly the same as your video shows.

[@LMAutoRepairs]

Hi Have you checked fuses etc? Check connections etc... Have you scanned the car? Thank you for watching!

[@christineoatley4650]

Have checked the fuses, all ok. haven't scanned it, we don't have a scanner. What connections? Battery ok. Gears get stuck in 3rd and won't paddle either way. Switch off ignition, switch back on all is well for a while as long as car stays in higher than 3rd gear. Great video, thank you

[@LMAutoRepairs]

@@christineoatley4650 Your problem does not sounds the same as the one on the video... I would advise you to get it on a good diagnostic session... otherwise is pure guess work...

[@christineoatley4650]

@@LMAutoRepairs Hi, I took the car for a diagnostic to Citroen this morning, it flagged up "Requires O/S/F ABS sensor

[@LMAutoRepairs]

@@christineoatley4650 Ok... providing wiring has been checked... go for it! 👍

[@smenal]

...mine had an ABS sensor (front right), that was causing these kind of errors

[@LMAutoRepairs]

Same symptoms different root cause.. 😉 Thank you for watching and for your comment!

[@carsurgeon7736]

Hi fantastic vid bud well explained I have a citreon c4 grand Picasso 2008 1.6L diesel 2008 that has a esp light and abs light on its also not shifting passed 3rd gear some sort of emergency mode I presume ,I cleaned the abs sensors on both front wheels still the same issue. I called the RAC to have a look and they've said it's a communication issue with one of the computer modules what do you think could be the problem I'd really appreciate the help bud 😁

[@LMAutoRepairs]

Difficult to say... If there is no communications with one of the modules, start by checking fuses, power and grounds to that particular module... Communication lines etc... 👍👍👍

[@carsurgeon7736]

@@LMAutoRepairs sweet thanks for the response I'm going to try that and let you know thanks again

[@LMAutoRepairs]

@@carsurgeon7736 👍👍👍

[@emmahutchinson744]

@@carsurgeon7736 did you ever find the issue with your car? I'm currently going through the exact same with mine at the moment.

[@maforautorapair5935]

I like this video , great job ,In the same case in my strategy, If the fault code indicates a loss of communication with a single module I check for proper power and ground circuit at the affected module , if the circuit are confirmed good , then test the CAN circuits for opens between splice to the CAN network and the module , if the circuit do not have open , replace the module What do you think of my strategy ?

[@LMAutoRepairs]

Good approach... can't see anything wrong with it... I also do the same... in case, experience told me to approach it in a different way... Thank you for watching!

[@emameyer]

great video! what is the scanner you use? which one would you recommend to diagnose a C4GP with ESP/ASR fault that came out of nowhere?

[@LMAutoRepairs]

Hi Can see you do not follow my channel... lol I use the Autel Maxisys MS908P.

[@LMAutoRepairs]

@@drugwiseproject8151 Hi It is difficult to make any sensible guess based only on what your description of the problem... You are going to need to have it properly scanned, look at the live data etc... Thank you for watching and for your subscription! You can try kzbin.info/www/bejne/a3vPkKOle5holaM Myself or a fellow member, will be more than happy to help!

[@Thunder2838]

Hello, great video! I have a similar problem with all the warning lights and messages, however I also have an additional problem, the gear selected is showing as '-' a minus sign rather than neutral which means that I cannot start the car, do you have any idea what could be causing it? Thank you,

[@LMAutoRepairs]

[KF]Thunder^ Hi It can be the same problem... it all depends which wires are damaged... Obviously it can be something different... Have you scanned the car? Thank you for watching!

[@Thunder2838]

@@LMAutoRepairs I have scanned the car however no error codes are present... I believe it may be something to do with the gearbox actuator?

[@LMAutoRepairs]

@@Thunder2838 Possibly... weird that there is no codes... What about live data, is anything out of the ordinary?

[@daisyvlogs2622]

Kf thunder did u get this sorted I've got same problem, I've just changed the gear lever as that had a fault now I can select r,n,a, an manual but no gear display on instrument panel just a -- symbol an great video again lm auto I will subscribe wen I work out how to lol

[@Thunder2838]

@@daisyvlogs2622 Yeah, got it sorted in the end! After wasting a year or two taking it to Citroën specialists, dealers and many others who didn't have a clue what's wrong with it, it turned out to be the gearbox hydraulic motor which I replaced and it worked straight away! Therefore, from my personal experience, if someone is encountering the problem of the selected gear showing as '-' (a dash) I would highly recommend that you first of all check or get checked the gearbox hydraulic motor and ensure that it hasn't failed rather than wasting a year or two taking it to Citroën specialists, dealers etc... Which is the exact mistake that I made.

[@gee3770]

Thank you mate !😀

[@LMAutoRepairs]

😊 👍👍👍

[@globalcarparts4209]

keep up the good work,thanks

[@LMAutoRepairs]

Global Car Parts Hi Thank you for watching and for your comment sir...👍