Peugeot 207 ESP light on. Fault finding and repair.

[@beluxauto5968]

Nice video . Pretty straightforward diagnosing these pumps and easy swap if everything is rust free .

[@LMAutoRepairs]

Indeed... and no programming required! 🤣🤣🤣 👍👍👍

[@nabskikda3590]

Hi you are doing really good work,I have problem with my peugeot 207 2008 hdi airbag light on took it to a garage they couldn't fix it the codes I have are p0651 ignition positive supply volt and the data is showing neutralization switch faulty please help me if you can thank you ,and if you have wirring diagram that would help me a lot as the plugs under the seats have five wires and I don't know what they are. Thank you

[@lukp4297]

Hi I'm like your Chanel very professional fix. Did you had some case in past with ESP light on ford focus MK2? Please maybe you can have idea where I should look for mistake. Symptoms are when the engine reaches the temperature of 90 degrees, the esp light comes on and the tachometer pointer works once and does not work. When the tachometer stops working, the engine runs erratically and goes off. After reading the fault codes, it shows ABS U2023, EPS U1900-20, IC U2196-20, and OBD2 P1132 When the engine is turned off and on again, the light goes out and the engine runs normally, ESP light comes back again in few minutes. What I noticed that after removing the plug from the temperature sensor when engine is working and cold on the dashboard the ESP light comes on have same symptoms as after engine get 90 degrees. I replaced temperature sensor for new original didn't work still same problem. I know that you could fix this very fast because you have professional knowledge. Kind regards

[@LMAutoRepairs]

Check for air leaks etc... Check check live data... Looks like the ESP light is coming on because of the engine faults... Thank you for watching!

[@lukp4297]

@@LMAutoRepairs Thank you very much for responding. I'm always watching your new videos 😀

[@Adam-wu7vt]

The Focus MK2 can suffer from bad solder joints in the instrument cluster, I had an immobiliser fault on mine that was due to the instrument cluster.

[@lukp4297]

@@Adam-wu7vt Thanks I was checking instrument cluster.

[@LMAutoRepairs]

👍👍👍

[@jedjones9047]

Great video I've got same problem with exactly same model car If I get abs pump module from same model car and same year will it fit ok or do serial numbers have to match the numbers on mine are missing any help would be appreciated. Many thanks

[@LMAutoRepairs]

You should be able to see the numbers on the ecu information with the scan tool... Nevertheless, yes, as far as it comes from the same car, should work... 👍👍👍

[@jedjones9047]

@@LMAutoRepairs thanks much appreciated

[@LMAutoRepairs]

👍

[@mrgrumpy5116]

hi, Louis you must have thought about using the new valve block with the original ecu, is there a reason why you didn't do that? .. thanks for the video

[@LMAutoRepairs]

Not really... they are not coded to the car... was just easier to straight swap... Would have to remove the whole unit to separate the two parts any way. But you can obviously do that... 👍👍👍

[@DieselPower1968]

Great piece of advice and help..just looking at a 207cc that's up for sale with this exact problem..what's the total cost for having this done..

[@LMAutoRepairs]

Hi The price or the unit and a couple of hours labour... I guess... Thank you for watching and for your comment! 👍👍👍

[@Axlg]

does the steering wheel was hard to turn with that ESP error ? I have a 207 too, is not CC but looks exactly like that one (interior, engine, everything) Im not mechanic, im having that error with abs, and the steering wheel very hard for like 3 years now. Is very intermittent. Peugeot wanted to charge me to change the electric power steering motor, BUT i dont think thats the problem, (it would not have to work intermittently). The last month the steering wheel worked for 10 days in a row. I got an AUTEL, so im going to do tests with it. Do you think if I get 0 data in braking pressure, it is very likely to be the abs pump failure? Sorry for my english. im from Argentina. I saw your two peugeot videos and really like them!! Best Regards.

[@ferdiyurdakul]

Im surprised that it doesn't need coding. Same issue in focus/v40 too

[@saidrezgui8223]

Hi I have exactly the same problem on a peugeot 1007. Unfortunately impossible to find the ate reference. a vendor selling a different reference told me that it will work if I code the abs bloc with a diag tool. if anyone can tell me if its true ? and is it possible to code it if I just plug the electric part of the new one without taking off the old one? To be sure it works before taking off brake hoses and bleed the system. thanks. edit: great video , so easy to understand what to do

[@ahmedledraa572]

Good fix again, About mileage, is not necessary programming the abs kms?

[@jasonwilliams4212]

All live data is in km/h

[@vladutz76]

Thanks for the video. Is there any chance to permanently deactivate the ESP using that tool?

[@LMAutoRepairs]

Possibly... Depends on the models... 👍👍👍

[@vladutz76]

@@LMAutoRepairsFor 207? I should have mentioned.

[@markobezjak6952]

And He fix it one more. 👍 Thank you for the video.

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@BOSKILLZX]

Hi Again LM, I’ve since had the car read and it was the same fault code C1302. I bought a second hand pump, a mechanic has come round to fit it. The original code has cleared but now shows a C1398 which is a programming fault. Have you come across this before, the mechanic is advising I take it to specialist or Peugeot themselves to programme it. I was confused as I thought there was no coding, the part numbers were the exact same. I’m really lost, it’s becoming a real headache. Any help appreciated 😢

[@LMAutoRepairs]

Hi Is that the same car as the one on this video? Is that trouble code, stored on the ABS/ESP module or on a different module? 👍👍👍

[@BOSKILLZX]

@@LMAutoRepairs Thank you so much for the reply, yes the car is Peugeot 207 1.6 although it’s the CC model, looking at the part number on the pump it’s the same as this one. I’m not entirely sure what you mean regarding where the code is stored, I’ll ask the mechanic. But he came with a diagnostic tool which read the exact same code as in this video, the used abs pump I bought removed the fault but has produced another one. I’m tempted to buy another used unit, what do you think?

[@LMAutoRepairs]

@BOSKILLZX That code indicated that the module you bought has a different configuration... All it needs is configuration, pp2000 or diagbox should be able to do it... Perhaps the unit you bought came from a normal car, and not a cabriolet, or something like that... 👍👍👍

[@BOSKILLZX]

⁠​⁠@@LMAutoRepairsAbsolute legend thank you, I’ll pass this on to the mechanic. Sent you a little something on ko-fi to say thanks😄

[@LMAutoRepairs]

@BOSKILLZX ☺️ 👍👍👍

[@fam.a-r9140]

Hi, I have opel corsa c 1.0 ecu doesn't work anymore, can you tell me please if i change ecu kit complete do i need to programing?

[@LMAutoRepairs]

No... But easy to just change the ecu on those... Thank you for watching!

[@alanoo4470]

Hi Luis. I have exactly to my car Citroen c2 , I not can't resolve my problem . How can found you? Thanks

[@LMAutoRepairs]

What do you mean? If your problem is exactly the same as per the video, just follow what I have done, and that should sort the problem... 👍👍👍

[@marcinwyrwa6617]

What is the difference when diagnosing Autel Maxisys and Autel Im608

[@LMAutoRepairs]

None... The diagnosis interface and capabilities, from what I have seen so far, are exactly the same... Thank you for watching and for your comment!

[@marcinwyrwa6617]

@@LMAutoRepairs Thanks for the information;) So for all brands IM608 is better :)

[@LMAutoRepairs]

Well... is the same... You have the immobiliser and programming on top... but it does not do BMW and Mercedes flashing...

[@jothain]

Wow, at 10:00 that cover is actually open below in Peugeots? That's nasty design for that wiring connector. Water, salt, grime etc. Sure there's the wheel liner, but still that's quite nasty location. Edit: Forgot to thank for good video again 👍👍

[@LMAutoRepairs]

😊 👍👍👍

[@kevinpalmer7452]

As always great diagnosis and repair

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@peugeotobsessed7772]

About time someone put one up about a esp pump fault been having this problem awhile thanks does the replacement abs esp pump need to be the same part number ? ?

[@LMAutoRepairs]

The same or a compatible one... But try to fund the same... Thank you for watching!

[@peugeotobsessed7772]

Thanks for your help

[@LMAutoRepairs]

👍

[@BOSKILLZX]

Thanks for this video, do I need a specialist diagnostic tool to take the light off the dash or would fitting the new abs pump automatically disable it if it’s the culprit. Thanks!

[@LMAutoRepairs]

Might needs faults clear... but don't need nothing special for that... 👍👍👍

[@BOSKILLZX]

@@LMAutoRepairs Thanks for the reply, the problem I’m having is that the fault code doesn’t show up on a cheap OBD scanner. So I haven’t actually diagnosed the car yet, but based on reading it’s likely the abs pump or wheel speed sensor. I found a cheap used part for the pump and thought I could just test it by fitting it,was hoping it would just clear the fault on dash straightway(if that was the cause of the fault)

[@LMAutoRepairs]

I wouldn't do that... Parts cannon is never the way... Any local garage will scan the car for you for a small fee... from there you can do a much more informed decision on how to proceed... Replacing parts just in the hope that it will resolve, is not very advisable... plus, you might need to clear the faults anyway...

[@BOSKILLZX]

@@LMAutoRepairs I’ve already got the car up in the air with the wheel off. The only thing that’s stopping is rusted to death torx screw to get the arch liner off 😂😂

[@LMAutoRepairs]

😅 They can be a nightmare... 👍

[@sulemanhabib1743]

Thank u my boss (L M A) nice video, continued your good work for us.please for the seek of your viewers, clicking on the icons on the scanner,we need your voice on them. Habib Auto all day way from Ghana Accra West Africa

[@LMAutoRepairs]

😊 👍👍👍

[@khalifaalshawoosh1892]

Thank you so much 😊 I replace it and it’s working now 👍🏻

[@LMAutoRepairs]

That's great! 👍👍👍

[@misu377]

Haloo y have same problems whit my car I bay a second hand unit but the problems not solve , exactly same error code , is it probably bad unit too?

[@LMAutoRepairs]

If you have checked everything else, most likely you got a bad unit... Thank you for watching!

[@misu377]

What else exactly do I have to check?

[@LMAutoRepairs]

Power, grounds, communications... 👍

[@misu377]

@@LMAutoRepairs ok thanks

[@misu377]

I have 3 code error U 1208 no communication with engine ecu c1390 regulation of engine torque end c1302 brake pressure sensor no signal

[@Misadventures2018]

Is this the same for a 407 sw

[@LMAutoRepairs]

Possibly... Never did it on that one... Thank you for watching!

[@rhiantaylor3446]

Well if you say the pressure sensor can't be fixed, it can't be fixed. I have never watched you miss an opportunity to open a sealed unit before, with a view to repair of course.

[@LMAutoRepairs]

😊 👍👍👍

[@MrJavedbaghlani]

if you live happy don't buy rubbish cars like peugeot, citroen ect....

[@louisbeeston7647]

What is it that you replaced

[@LMAutoRepairs]

As per the video... 👍👍👍

[@louisbeeston7647]

@@LMAutoRepairs what is that part called. What pump is it, I would like to know becasue it helps me with this assignment I’m doing

[@LMAutoRepairs]

It says on the thumbnail... ABS/ESP unit...

[@misu377]

Whit this problem the engine is in limp mode?

[@electronic7979]

Super 👍

[@LMAutoRepairs]

Thanks! 👍👍👍

[@SabretoothBarnacle]

Excellent stuff🚙👍🏻😁

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@hashirnawaz4532]

Good morning and Nice video

[@LMAutoRepairs]

Thank you! 👍👍👍

[@jasonwilliams4212]

What I normally do in this case is just change the module as this saves a lot of time trying to bleed theses out.

[@LMAutoRepairs]

Was a quite straightforward process to be honest... In this case wouldn't work... the pressure sensor is actually in the modulator... Thank you for watching!

[@chrismcguiness6952]

I've a berlingo with asr/esp on start up. Once I hold break it clears the break again its back on. Tried break switch not related

[@LMAutoRepairs]

@chrismcguiness6952 Have you scanned the car, to see what faults are logged?

[@nemanjadzombic6101]

Thank you for another great video!!!

[@LMAutoRepairs]

👍👍👍

[@saibabupodala6297]

Good information nice video Make one video ur mobile van learning some New technician how to make mobile van and using thank you ...

[@LMAutoRepairs]

I don't really do mobile stuff... Very few exceptions... Will might plan something... Thank you for watching and for your comment!

[@foxsittofox8567]

Thanks man!

[@LMAutoRepairs]

😊 👍👍👍

[@muradali1519]

Sar plz I need ur help

[@planetpowersteerings3502]

No need to perform any coding or programming for used unite.

[@LMAutoRepairs]

Not for this particular car... Thank you for watching!

[@iankelly2110]

Good job guys

[@LMAutoRepairs]

😊 Thank you!

[@trevorcornes1056]

Brilliant very interesting 👍

[@LMAutoRepairs]

😊 👍👍👍

[@abdallahtanjawi9421]

good man good job thank you

[@LMAutoRepairs]

Thanks! 👍👍👍

[@renatairmarius123]

Hi thanks for video.

[@LMAutoRepairs]

😊 👍👍👍

[@saadi747]

❤❤❤❤

[@LMAutoRepairs]

😊 👍👍👍

[@viktora762]

good one!

[@LMAutoRepairs]

Thanks! 👍👍👍

[@Username64870]

Good..Good..!

[@LMAutoRepairs]

👍👍👍

[@aymenmohamed1134]

👍🏻👍🏻👍🏻🌷

[@LMAutoRepairs]

👍👍👍

[@andyg817]

Awful position its located, near the wheel arch , attracting all thè crap and rain ...

[@LMAutoRepairs]

Indeed... But it is not just this car... plenty of other manufacturers use the same or similar locations for the ABS/ESP units... Unfortunately... 👍👍👍

[@andyg817]

@@LMAutoRepairs ive got one of these, 207 gt.... had it one year.. done a fair bit on her so far.. I've had my esp light come on.. found the top connector blocks on the fuse box, had water in, sorted.... 👍 thanku. Good video, .

[@yousefbhoyroo6960]

Nice

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@johnmwangi6291]

✍️

[@LMAutoRepairs]

😊 👍👍👍