It's great that you tried to make the LogPer from printed circuitboard, as suggested in the comments. This is truly experimental science at his best! Good for you! 73 PD0PSX the Netherlands.
@ecotech41489 жыл бұрын
Thank you for al this vides.
@jmanjulian9 жыл бұрын
The picture in the calculator (and other google images of LPDA antennas) point that the feed point of this antenna is the front. You however are feeding it from the back side. Is there a reason you are doing it this way? Doesn't it have a negative effect to change the feed point?
@adistef9 жыл бұрын
I am using Yagi Calculator by John Drew; i made a couple of them for 2.4 Ghz: long ones, short ones, metal boom, plastic boom and they worked great; please tell me what you think about Mr . Drew software, becasue his calculations were a little different compared to other ones I found online.
@thesmartass573 жыл бұрын
20 years in the field and all my LP where end-fed !!
@an89533 жыл бұрын
Love your work 👍👍👍
@Vigilence9 жыл бұрын
That's some sexy soldering closeups thank you :D Another awesome video!
@netpixels9 жыл бұрын
interresting video, thanks for sharing. One thing which would be very interesting to me and surely many others would be a comparison in terms of performance of this build vs. the Bi-Quad you built previously. It's difficult for me at least to fully understand the actual pros/cons of each build in terms of how they preform in short distances, long distances including actual aprox beam width signal quality/drop-off points. Would you mind providing a bit of clarity along these lines? Again, thanks for sharing all your helpful build videos!
@andrewmcneil9 жыл бұрын
+Christian Hochfilzer Hi Christian I am planing on filming a test over some distance as well as a bit of theory as to why some antennas work better over long distance but are not as good over a much shorter distance.
@netpixels9 жыл бұрын
That would be very helpful. While I personally do understand the general differences of the various antenna types I can't exactly figure out if I should attempt to build one of these, a directional panep antenna or that Directional Bi-Quad of your which is my personal favorite of your builds.
@dennismanning99538 жыл бұрын
Thank you for your excellent videos . I am a complete novice at all of this. I realize tho so s almost BASIC question but how is the antenna actually connected and to what? That is, is it connected via coax to a router or to the laptop, for example? Thank you fir your patience with my qquestion
@MrAndroidhands8 жыл бұрын
I have a 60cm boom with the same frequency but the calculator gives same dbi as your antenna. I need it for long distances so does anyone know how to increase range
@tracibeacer6709 жыл бұрын
I'm into rc planes and find your videos of great interest.If I was to buy one of these or foolishly try and make one ,as there are so many variations on the 2.4 frequency which one would you advise. Looking for long and straight flights!Many thanks s
@MrDeeejaaay7 жыл бұрын
If you used complete di-poles you would probably have even better performance. A true LPDA has a + and - element for each position.
@ieeeleadinguniversitystude7904 жыл бұрын
Hey, Andrew mcneil, Thanks for creating this video. I wanted to know what other material is best for antenna 3Ghz-12Ghz range? Can I use copper/brass/stainless steel as Element and Boom. What are the best material for boom and element?
@NicuIrimia9 жыл бұрын
Have you tried feeding from the tip?
@RobertJochim9 жыл бұрын
The wider bandwidth you cite is probably a product of the diameter of your elements - 2mm in this case. You'd be much tighter to the 2400 - 2500 MHz target if you had used a 1mm wire or tubing.
@donnypodcast3 жыл бұрын
How exactly is the coax soldered onto the boom? I'm not exactly sure, but from what I saw, is the braid twisted into a wire and soldered on one side and then the center wire soldered on the other side?
@philnyc3 жыл бұрын
Andrew, a Quick question. I've been making lpda Antennas for the 144/430 amateur radio bands and their design are fed with coax from the front of the boom. May ask why your design is fed from the end. Does that make a difference from Which end the feed point empowers the aerial? The only difference I am noticing is that your dipoles are unevenly spaced out. Antennas I've made, have equally distant dipole from both ends of the boom. Thanx. Great work on your part w these Antennas TBH 😀
@natebecks69109 жыл бұрын
would it have been easier to use a propane torch? or would the heat of it have warped the boom? i know you would have had great heat distribution on both the boom and the element and a good solid connection.
@hoggif9 жыл бұрын
If you have an analyzer, I'd love to see impedance or reflection coeffiecients (like SWR) measured for the antennas. You could perhaps use a directional coupler and a spectrum analyzer/power meter to check for matching. A dremel with a cuttting wheel could perhaps be used to cut the rod without loading the soldered joint if you need to cut it after soldering.
@andrewmcneil9 жыл бұрын
+hoggif Hi yes the main reason I wanted to build this antenna is to use it as a reference antenna for the analyzer. I did try to use the dermal but the vibration made the joints loose.
@MrSailor503116 жыл бұрын
andrew mcneil When using a vice to cut elements the size of the vice seems to be an obstruction. If you measure then cut the element seem easier? Richard sailor50311@yahoo.com
@GeorgeGardinier9 жыл бұрын
very good for the reasons you said. do you know how far away is the distance of the test. can this be used for rv'er or caravanners outside in the weather
@corax20124 жыл бұрын
Don't know how I overlooked that calculator. I suppose that's just for ideal performance, but it's goofy that each element is different by 1/10 of a millimeter. Don't think the hardware store sells it that way.😁 Any advice from commenters? Andrew doesn't leave comments.
@g1fsh9 жыл бұрын
Do u have an electronics channel Andrew?
@tracecommunications8 жыл бұрын
It looks as if you are using the log periodic antenna in the horizontal polarization mode. Aren't most Wi-Fi antennas vertically polarized and shouldn't you orient the log periodic vertically?
@eknaap88007 жыл бұрын
@tracecommunications: Most of the received long range signals are reflected ones. The tend to change their polarization often. Furthermore, horizontal placed antennas are a bit more directional as they do not 'look' sideways as vertical ones.
@trench019 жыл бұрын
What would be the top 3 long range wifi antennas that you have since you have so many.
@sokolum9 жыл бұрын
Is it also effective for transmission?
@GeorgeGardinier9 жыл бұрын
also if you had these in your store you could make a sale