FYI, the other speaker had the same problem and I fixed it the same way 💯😎.
@jimrankin6634 Жыл бұрын
I used this technique and an old HP PS, and now my 5.1 lives again. Thanks bud.
@JustBarran Жыл бұрын
Glad to help
@OnHoldAt502 жыл бұрын
You're what we call a board-level technician. Nothing wrong with that, but it would have been worth your time to bring that simple power supply to the component level. Something made that resistor get hot, you could do it. * Regardless, I came here to find out how you fished the main board out. I got so much more, because of your complete disassembly. Thanks man, kudos.
@JustBarran2 жыл бұрын
Hahahahah I not gona lie, you are right 😂😂, I was tempted to dig in some more but it wasn’t worth my time since I had a powersupply to replace it, dw next time
@matimobilia4 ай бұрын
You save my birthday, tomorrow i make a party and i fix my z506 with this metod! Many thanks!!!
@enforcedraccoon8648 Жыл бұрын
Worked great! Thank you. I used an onn brand 19 volt, 4.7 amp computer charger and so far it’s working great. Got the Logitech system for $10 and the charger for $5. Not a bad deal at all lol
@JustBarran Жыл бұрын
That's a great deal 🙌 awesome stuff
@jccarpent2 жыл бұрын
Hello, thank you very much for that video. My daughter faced exactly the same problem and I fixed it thanks to your video ! We were so happy to save that device.
@JustBarran2 жыл бұрын
Omg it's always great to hear when my videos helps someone 💃. Thanks for your comment and keep fixing 🙌.
@tanewaatz73982 жыл бұрын
THANK U SO MUCH, I got a set for free because it was faulty, and now with an old laptop psu I can get it working, bless u. 💖💖💖
@JustBarran2 жыл бұрын
No problem mate, happy to help 💃🏽
@ZikiDwiJR Жыл бұрын
my z506 got broken this week, sound cutting out arround 70% - 100% volume and I think it get worse everytime, now I can only play at around 20% - 25% volume. already checked the mainboard and the cable, all looks good. not yet check the power supply yet because it's kinda hard to reach, but thanks for your video that confirm it can be replaced with laptop power supply and I have some spare laptop power supply
@JustBarran Жыл бұрын
No problem, just be careful power supplied tend to have a capacitors that store charge so try and discharge the unit before testing and let me know how it goes. Happy to help
@waiora_wf3 ай бұрын
Same speakers started out with a slight buzzing sounds, when it was cold in winter time the buzzing would be worse if speakers were off and eventually fade when using them. After a few years the buzzing stopped but speakers started cutting out at 30-40% vol. Woke up one morning with power tripped and when i switched everything back on, the speakers were just dead.
@damiantobaj597711 ай бұрын
hello, I subscribed to your channel, I have the same problem, but I don't know if I can use the old Lenovo 20V 4.5A power supply?
@JustBarran11 ай бұрын
Hi, this one I am not sure about the 20v might work but it would be risk. I most I tried was 19v
@damiantobaj597711 ай бұрын
@@JustBarranwhat exact power supply model did you use?
@JustBarran11 ай бұрын
@@damiantobaj5977 18.5V 3.5A 65W HP Pavilion DV4 Power Supply
@damiantobaj597711 ай бұрын
@@JustBarran I bought the same one, I haven't cut it yet, but which cable is + and which is - in this HP power supply
@JustBarran11 ай бұрын
Hi, this would be different between models but I recommend using a multimeter to check this.
@brokensilence513 жыл бұрын
Great job bro, love the step by step breakdown of the troubleshooting process, and also your thought process. Keep it up!
@JustBarran3 жыл бұрын
Thanks at bro, 🙌🏽 people don’t realize fixing isn’t a to b it’s a to b c d ……. And the solution might be all the away at z
@daansteeman52272 жыл бұрын
I can see the same resistor looking... a bit fried. But I couldn't get either of the boards out. I was about to rip the box to pieces and fix it later. But now I know the boardremoval and voltage. So I can either fix the board of just change the PSU. Thanks!
@JustBarran2 жыл бұрын
Hahaha i know things like this does make people get frustrated. Happy to help
@triplemmenace6 ай бұрын
Hey, the sond emitting from my speakers sounds like it's breaking up and sounding distorted when the volume is proberly on only like 35%. Don't know if it's the speaker ffrom the box or something else. Could you give some advice. Thanks
@JustBarran6 ай бұрын
Hmm not sure to be honest. Distortions come from noise or a bad component in the amplifier
@triplemmenace6 ай бұрын
@@JustBarran I should have clarified b4. It's the logitech z506 speakers. The distotion is coming from the bass box. I think that the speaker is blown but I don't know if it could be something else. I disconnected the speaker but got the same result. Don't know if it's another component that has malfunctioned.
@edgardominguez90817 ай бұрын
I have one and the center speaker have some noise in the back ground and the sound is very low, do you know any way to fix it? I tried cleaning the input and the plug but did not worked.
@JustBarran4 ай бұрын
Sorry not sure, a number of issues could be causing that , could be short in the wire also or a bad transistor on the amplifier
@oneil2311 Жыл бұрын
Hello can a Logitech Z313 Subwoofer Speaker work in the Logitech z506 subwoofer as a replacement ? trying to find out online but it's really difficult
@JustBarran Жыл бұрын
Am not sure sorry.
@escapethematrix5379 Жыл бұрын
Speaker watt and impedance should be match otherwise it would be damaged to speaker or amplifier. So replacement subwoofer should be 25-30 watt max and impedance should be exactly equal.
@escapethematrix5379 Жыл бұрын
It should be between 20-30 watt, Don't play bass volume at max. Use 60-75% bass n volume. IT won't be damaged.
@dennisacheampong4910 Жыл бұрын
can I connect the z520 speakers to thr Z313 woofer, Bcos I want more bass in my sound
@JustBarran Жыл бұрын
Am not sure to be honest
@oOPaiNOo14 Жыл бұрын
Do you know how to fix the part where you plug in the speakers to the subwoofer? Cause the right front(black) female connector on the subwoofer is only making noise or static when i hook up my speaker.
@JustBarran Жыл бұрын
Sorry I returned the speaker to the owner, so I really can't say.
@adityam88882 жыл бұрын
Hi, should I use 15v 5A adapter or 19v 3.2A ? I appreciate your response, please help me choose don't say they're the same. lol thanks
@JustBarran2 жыл бұрын
Hey ether one will work, the 15v 5a is closer to the original powersupply so try and see if it works first and how it sounds. The only reason I used 19v was because it was what I had available. So if you have had to chose go with the 15V as it is more with in the original specification
@adityam88882 жыл бұрын
@@JustBarran thanks man I appreciated it, and yes it works like a charm! But now I have other problem the potentiometer is broken because I forced it without opening the screw at first lol..
@JustBarran Жыл бұрын
In one of the other comments on this video I give someone the link to a replacement pot, ask them if it worked
@escapethematrix5379 Жыл бұрын
Are you using 15 v.?? I think it will be safe. I replaced with 12 v but can't play at max volume IT play well around 70-80 % of total volume bass. Reply if 15v is working well.
@BlindMellowJelly Жыл бұрын
I have these and after 4 years they have a clicking tick almost like static. I checked my drvers and all but it remained. The fix was to remove my memory and wipe it with a damp cloth. I have my tower on the floor and have carpet. Bad move....static creps in but once wiped they are all good. Outstanding speakers if you are a hip hop head and a gamer.
@JustBarran Жыл бұрын
That's awesome. Yeah the problem would probably have been the sound card on the computer. These speakers work great
@BlindMellowJelly Жыл бұрын
@@JustBarran Perhaps but it was the memory that held the static. The sound card had nothing to do with the speakers. If left on they do tend to get a hum or a click but yes great speakers but still disposable
@ThePeterasd Жыл бұрын
will bluetooth connection allow surround sound (all speakers will sound?)
@JustBarran Жыл бұрын
Yea these speakers don’t do directional processing so what ever Input you put in would be equally play the output (L and R)
@ThePeterasd Жыл бұрын
Thanks again. I will try getting a Bluetooth adapter.
@LindellHarry Жыл бұрын
You just got a new subscriber love this video, hope to see more electronic fixes on the channel ❤
@JustBarran Жыл бұрын
Thanks a lot. Working on some more videos stay tuned.
@buhuhuh7757 Жыл бұрын
I have this speaker set and I wonder whether it's something that I could make battery powered? Perhaps a laptop battery and power supply?
@JustBarran Жыл бұрын
Hey, definitely I think that’s a good idea, you could also get a Bluetooth module also. In terms of battery it would need to have a decent capacity depend on how long you wanted it to play for. The speaks are DC so you just need to flow the video , but where I change to rectifier /power supply you can substitute that out for a DC jack and feed the speaker of a 12-19v supply /battery and you should be good.
@fixorfling70323 жыл бұрын
Nice wood smell, can we get that in a candle form?
@JustBarran3 жыл бұрын
I would give you a candle with the smell of my wood 😂😂😂😂
@fixorfling70323 жыл бұрын
Christmas gift that keeps giving 🤦🏽♂️🤦🏽♂️🤦🏽♂️🤦🏽♂️
@ShooterQ2 жыл бұрын
Hello, do you know if it's possible to modify this subwoofer for use with RCA input without the control speaker? I acquired the subwoofer by itself and i'm looking to see what I can do with it.
@JustBarran2 жыл бұрын
It should be possible since the control speaker doesn’t do much other than put on the amplifier and set the volume. It would require getting a pin out for the DB9/rs232 connector and making the required circuit. Check out this www.yoreparo.com/es/audio/audio/preguntas/1250316/logitech-z506-control-de-volumen-db9
@ShooterQ2 жыл бұрын
@@JustBarran Thank you.
@JustBarran2 жыл бұрын
No problem
@RM-ys4io2 жыл бұрын
is it better to use 19v laptop adapter or 15v ?
@JustBarran2 жыл бұрын
I don't think it should matter, I believe the original one was around 15v, once the current is around >2A
@RM-ys4io2 жыл бұрын
@@JustBarran thank you for your response, I was just wondering if using 19v will create a static or noise?
@JustBarran2 жыл бұрын
I really not sure, am not that deep in electronics to say
@andresvega54762 жыл бұрын
Thanks a lot I did the same test 'cause I've the same Logitech speaker problems. Gonna fix it now, Thanks for sharing your knowledge. Cheers from Mexico🤓
@JustBarran2 жыл бұрын
Awesome happy to help, remember to take all precations when wiring up even if is the dc side. Last thing you want is the box of catch fire. Other than that good luck and you can always DM me on Instagram if you need any further help.
@andresvega54762 жыл бұрын
@@JustBarran Yeah, I've used thermofit to cover everything. Also used a 19.5 volts 3.5 amp laptop charger. Thanks again
@JustBarran2 жыл бұрын
@@andresvega5476 awesome well you all set, and cheers from Trinidad 💃
@Haldrie5 ай бұрын
The real solution is to replace two capacitors on that power supply on the power output side which go bad. I am currently dealing with this very issue and found a reddit thread of several people also with the same issue and one person finally realize it was just those two capacitors on it which is the same conclusion I came to when I noticed the bulging capacitors after a few hours of troubleshooting and pulling apart the volume pot to clean it and resoldering connections only for nothing to work. It's a lot easier and cheaper then just tossing the whole power supply and replacing it. I'm currently waiting for replacements I ordered which is a set of 5 so if I have this issue in the future I will have some spares on hand.
@JustBarran4 ай бұрын
I check the caps on mines and all were fine. I just reach a point where I weight the time taken to find and fix the bad components or spend just replace it with something I already had lying around. I went with the lather. Sorry that you reached the same place 🤣
@drumreach59402 жыл бұрын
Great video man, can you tell me how can i find the potentiometer on the controller speaker(volume control)
@JustBarran2 жыл бұрын
It is a dual (double) 20 ohms potentiometer i believe, A 22 will also work. It looks like this. store.comet.bg/en/Catalogue/Product/25571/
@drumreach59402 жыл бұрын
@@JustBarran thanks much appreciated
@MeTr01DPr1M32 жыл бұрын
Hey bud, great video! I happen to have the same speakers, and with the same exact problem. Even have an old laptop power supply I can use. Just a quick question to clarify, you skipped really fast on the wiring and connecting the wires from that laptop power supply to the DC wire that connects to the board of the speakers. Any chance you can explain a bit further how you did that exactly? Would be greatly appreciated.
@JustBarran2 жыл бұрын
Hey no problem man. Sorry It was too fast. Not sure if you have a multimeter. But make sure the laptop powersupply is around 15v to 19v. I cut out the end from the laptop charger. This is the side that would have gone into the computer. On the AC to DC supply on the speakers. The little circuit board I threw. There should be a red and back wire that plugs into the main amplifier board. I cut that wire and spliced the red (positive) to the positive of the laptop charger. And the negative(black) to the negative of the laptop supply. Use a multimeter to make sure which one is positive and negative because laptop chargers vary the voltages. I put some heat shrink also before I did the splice and added solder after to finish it off. Then I pushed it Through the hole that the original AC plug would have gone thru. Tied a knot so it doesn’t pull out and fill it with glue stick. The I plug in that to the amplifier board and you should be set.
@MeTr01DPr1M32 жыл бұрын
@@JustBarran Nice one dude! Thanks a lot for the info. Wish you all the best, and happy projects! :)
@JustBarran2 жыл бұрын
@@MeTr01DPr1M3 no problem, let me know if you are successfully
@abdulllah012 жыл бұрын
@@JustBarran Hello. How many volts and how many amps does the adapter in it use? What power supply did you use? What value did you use?
@JustBarran2 жыл бұрын
@@abdulllah01 I not sure what are actually specification of the powersupply that originally came with the speakers, I believe from looking at the components it could be around 13to16v 5A , I replaced it with a hp laptop charger which output 19v 6a I can’t remember exactly cause I gave it to my friend.
@berkanindere47052 жыл бұрын
What are the values of the adapter you plugged in? Is there any problem if I use 12 volts and 3 amps?
@JustBarran2 жыл бұрын
The 12v isn’t enough because amplifier is rated for higher voltages, I think 12 may still working but it would affect the maximum output volume among other things
@trucchise659511 ай бұрын
@@JustBarrani get a very wierd doing with 18v, is it normal?
@abdulllah012 жыл бұрын
Hello. How many volts and how many amps does the adapter in it use? What power supply did you use? What value did you use?
@JustBarran2 жыл бұрын
I not sure what the Original one was, I believe it could be 13-15v 4A around there, the one I replaced it with was a ~19v 5A hp laptop charger. Anything around the should work
@smkumailnaqvi67212 жыл бұрын
Hey, I like your video.. what kind of Hp power supply you use..?? Is the normal one 19v and 45w comes with laptop..?? 🙂
@JustBarran2 жыл бұрын
Yea it was a standard old time charger, 19v about 3A
@robertdenisjustavino2102 жыл бұрын
Hello! Bro, my master speaker from my Z506 is "broken" according to the technician. He told me that I need to buy the master speaker, BUT that is not in amazon or any other website for me to purchase, or is it? Can the cable be fixed? Please answer. Greetings from Panama!
@JustBarran2 жыл бұрын
Hey Robert, when he says it is broken does he mean that the power supply is broken like in mines ? Or is the speaker with the knob broken. Because as in the video you can also try what I did and change out the powersupply with a old laptop powersupply first. If the power supply is broken the. The master speaker would not work also
@danieltan416411 ай бұрын
How do I connect the speaker with a laptop power supply board ? Not sure how it works 🙏🙏🙏
@JustBarran10 ай бұрын
You have to take out the old internal power supply and by pass it
@gabrielsama37892 жыл бұрын
Ya son como 5 casos que falla la fuente de poder en ese modelo de logitech. En mi caso reemplaze la fuente con una fuente de laptop sony, va funcionando como 5 años sin problemas. La nueva fuente la puse dentro del cajon del subwofer.
@JustBarran2 жыл бұрын
yea, thats what I did also, great minds think alike
@stephenschilling1020 Жыл бұрын
Hey nice info. But I bought 2 sets at the same time, I paid $70.oo each at a computer show. one has gone (kaput). I have had them for a long time. Don't think I'm gonna try this as it would cost half what I paid for the full set. And time to put into it. Thanks for your video as I was going to try to fix it, but think I'll save the time and get an upgraded set up. And go back to Klipsch, or set up with Atmos. Not sure yet.
@JustBarran Жыл бұрын
Hahah that’s a great deal you originally got, but yea I feel you, sometimes the repair is not worth it. See if you can sell it broken or give it to a repair shop at lease they can up recycle it. A lot of people will be looking for the speakers or control speaker alone too.
@Knight-Orthodox6 ай бұрын
can make video to open z506 center speaker?
@JustBarran6 ай бұрын
Sorry this was a repair for a friend, I don’t have the speakers anymore
@LeonedeBeaumont2 жыл бұрын
Liked the video! Very good! You've fixed the issue of that speaker. Well, there's one thing I want to try. I bought a DB9 RS-232 cable female to 3.5mm male (since there's scarcity on the shop for male to male) then just bought another RS-232 male to male then will use a soundbar model LP-1807 (detachable L & R) with R bar as main then control as bluetooth and main control speaker. Hopefully it will work xD Subbed!
@JustBarran2 жыл бұрын
Hey would love to hear how this works out so keep me updated. Adding Bluetooth to this would make it so much more valuable as a sound system
@LeonedeBeaumont2 жыл бұрын
@@JustBarran Once I've received the cable, will test it out then get you updated xD
@LeonedeBeaumont2 жыл бұрын
@@JustBarran Didn't work bro 😅 I think only analog speaker with rs232 will work and not the digitized ones.
@ArturoAV10 ай бұрын
I tried this with an 19v 3.42a charger, the speakers turn on for a second but then the energy fades away and wont turn on until I disconnect the laptop power supply... Im not sure what im doing wrong :(... The charger says it is INPUT: 100-240V~1.6A 50-60 Hz OUTPUT: 19V 3.42A Do I have the wrong values for my laptop PSU? Thank you in advance!
@JustBarran10 ай бұрын
Likly that the laptop psu Is detection a high current spike and going into protection mode. Check and make sure their isn't a short circuit any were or that the power supply is not faulty
@ymediatt58503 жыл бұрын
Can I bring my speaker to fix as well?
@JustBarran3 жыл бұрын
Depends is it a Logitech?
@coladict2 жыл бұрын
I tried to open mine, but both the control speaker with the buttons, and the subwoofer panel are glued inside. There's nothing wrong with it, except i want to see if I can turn the whole thing into a passive speaker system, since the *ONLY* 5.1 HDMI ARC decoder on the market has an internal amplifier. Yes, there is only one such product and it's discontinued. These are just remaining units. There are $2000 audio mixers that support HDMI ARC input, but that's a professional studio system with about 30 I/O ports of various kinds.
@JustBarran2 жыл бұрын
Hmmm good points it would be something I have to look deeper into myself and get back to you but at that price it that audio mixers are nt worth it
@coladict2 жыл бұрын
@@JustBarran Update: I managed to get the subwoofer open and adding the new direct input was easy as soldering two wires to the speaker, then on the input port, drilling a hole and gluing it there with hot glue. Also on found which two pins in the DB-9 go directly to that speaker. When looking at the RS-232 layout as reference, pin 6 is the signal + line and pin 7 is ground. Got a DB-9 connector wired to an RCA jack and it worked as expected. The whole system of course is unplugged from power. Don't want to know what will happen if I turn that on.
@JustBarran2 жыл бұрын
@@coladict did it work?
@coladict2 жыл бұрын
@@JustBarran The new inputs work. I haven't tried the old ones, because my 5.1 optical audio decoder is has a buffering issue. The longer I leave it on, the bigger the audio delay. It reaches a full second of delay within just 2 hours.
@JustBarran2 жыл бұрын
@@coladict dam that's a big delay, hope you get a work around
@jsailentkillerboy13272 жыл бұрын
Hiibro my Logitech z506 model 5 days working next day not working rear or left speaker very low volume problem telme solution bro
@JustBarran2 жыл бұрын
Could be the speakers them selfs
@Bmagj2 Жыл бұрын
Eehy watchu ylknow about di Lofi gyal?? 😂 Great job my fellow ee/me engineering coop! I actually received these speakers today wuth the understanding that they dont work. On a preliminary test, I observed massive heat on the DB9 control cable and no output sound on the control speaker. This has to be a dhort- no?? Do you think that could be a short either on the output stage or the right speaker?
@JustBarran Жыл бұрын
Hmmm heat on the db9 seems weird, yet it definitely means something shorting but also that should be a low voltage circuit. I would check all the connectors because that is serious weird
@kurtnelle3 жыл бұрын
Yes, you should post attempts as well.
@JustBarran3 жыл бұрын
Thanks Shawn, I guess it’s the Journey not the destination
@alexandro33852 ай бұрын
Tenho um porém de vez em quando o volume fica oscilando. acredito que também seja a fonte de alimentação.
@Mominvloglife Жыл бұрын
10:10 same Problem Plesse solve the 😢 How to Fixed in Bangladesh
@JustBarran Жыл бұрын
Hey the video sloved the issue
@trucchise659511 ай бұрын
Is it normal that we don’t get a a clear sound? I can’t really enjoy my music with this solution, I get a dirty sound I don’t know it it because of the power of others
@JustBarran11 ай бұрын
Nah, something else might be the issue. The sound on the one I deliever was clean. It could be noise from a bad power supply used, bad input connection or cable or bad sorce. I recommend try the input with another speaker and seeing if you hearing a similar sound. If not it could be one of the ampliers for damage from the original failure of the powersuppply
@piresngaihte61118 ай бұрын
Mine also got an issue with the centre speaker low sound. Compare to others
@JustBarran7 ай бұрын
Not sure about that sorry
@chrismb73 жыл бұрын
Did he just say he want to “ destroy that box “ 👀👀👀😂😂😂
@JustBarran3 жыл бұрын
No boxes was destroyed in the making of this video
@marvinfrancis73432 жыл бұрын
My systems keeps playing and cutting off repeatedly... don't know what's the problem?
@JustBarran2 жыл бұрын
Could be a number of things from a faulty cable to a bad power supply like in the video. Would be better to see if you can isolate the cause of the problem, Eg it cut of when you move the system, or when you try to play it too loud. It could also be a switch shorting out
@All3ju Жыл бұрын
Thank you.
@JustBarran Жыл бұрын
🙌
@barranfamily93793 жыл бұрын
Nice work, you still have more stuff to fix hun
@JustBarran3 жыл бұрын
Don’t remind me
@andreslezama39108 ай бұрын
como le añadistes el blutoo
@JustBarran7 ай бұрын
I used an external Bluetooth adapter
@trinib12 жыл бұрын
Watching this video cause I have a 7 year old Logitech Z506 which i bought from supertech in puna for $550 and still works perfectly. And I recently saw on amazon for this same brand goes for $264.64usd 🤣and the Logitech Z906 for $399.00 . So I have a damn expensive system in 2022. So I was just looking around to see what is the type of issues can occur and how to prevent them.
@JustBarran2 жыл бұрын
Thanks for watching 🥹
@trinib12 жыл бұрын
@@JustBarran not calling anything on my speakers but if anything goes wrong i know where to go 👍
@BonJoviBeatlesLedZep11 ай бұрын
Found this while my friends are trying to repair a Z506 power cord lmao
@JustBarran11 ай бұрын
Hope it helped
@BonJoviBeatlesLedZep11 ай бұрын
@@JustBarran We figured it out, but it was more shocking to listen closely and realise you also in Trinidad 💀
@benny69402 жыл бұрын
Very nice Thanks
@JustBarran2 жыл бұрын
No problem 🙌
@brokensilence513 жыл бұрын
You should probably get that drill checked out... I heard there's medication to help with that o.O
@JustBarran3 жыл бұрын
Yea I going “straight” to the the doctors 😂😭
@vaish63603 жыл бұрын
I blowed up my multimeter once by measuring AC voltage with DC set on it 😂😂
@JustBarran3 жыл бұрын
Sorry to hear that 😢, but yea making sure it’s set correctly is really important
@vaish63603 жыл бұрын
Don't be sorry for that !! Actually it was funny at that moment
@xtr3me711 ай бұрын
You can "blow up" your multimeter if you measure on the "ohm" setting and there is volts in the circuit though..
@Triniz53 жыл бұрын
for the algorithm
@JustBarran3 жыл бұрын
❤️ 🙌🏽
@gabrielaraez42752 жыл бұрын
Mr. Barran: I don't see the interesting part of what you buy. We would like to learn not only electronics but to program Arduino building anything useful either for home or for industry. Still, thanks for your input.
@JustBarran2 жыл бұрын
Hey this video doesn’t deal with any Arduino stuff. It’s a simple power supply replacement. If you want to learn more about Arduino and programming you can check out my Arduino playlist kzbin.info/aero/PL1vbJjS91-vTXzdub3zvdHWlKBgM8xkhz stay tuned for more videos coming soon