Long Range FPV RC Car Remote - RadioLink RC6GS v2 Review & Unboxing

[@rcbear5863]

So this thing goes further than a crossfire on 1w???

[@ChaddRainsFPV]

No, but it does go farther than a really good analog 5.8ghz video system. And so it is a much better option for a lot of people that are just getting into FPV RC cars 🤙

[@Gordon-Scott]

@@ChaddRainsFPV I agree with this. I do run crossfire and of course it will give you more range but then you have video to contend with…

[@QSpeedRacer]

No. It's 2.4ghz at 100mw. And I don't think it's Lora cause 600meters isn't far. For penetrating trees and buildings I'd want atleast 250mw cause theoretically 250mw 2.4ghz matches range of 5.8ghz 1w (video feed)

[@stevefox3763]

I haven't used crossfire and Dont know how they compare but you can flash R9 gear with elrs firmware for even better range though I haven't done so as the reason I would want to use elrs firmware is to use the cheap elrs 900mhz RX's but all of them output on serial and I need ppm/sbus. I use R9 Slim+ RX's on everything, they output sbus but also 8 regular pwm, they also have inverted and uninverted s.port . I love the s.port, I use it for forwarding mavlink telemetry from a flight controller and on my Tx's colour screen I have all the data like voltage, current, speed, distance etc plus satellite mapping showing the position of the craft :) The R9 system supports its own telemetry like rssi, voltage ect and you can buy all sorts of sensors but if you have a flight controller as the brains of your craft, all you need is already there.

[@neubianx]

So anxious for FPV racing leagues

[@ChaddRainsFPV]

FPV Rc Cars are so much fun to race. If more people had the range they wanted I’m sure we’d see more racers haha

[@walterhartman]

Very cool. I like the extra channels with the dial for a pan/tilt control. I really want to turn my car into a robot with the abilities to look around and pick things up.

[@ChaddRainsFPV]

Picking things up would be awesome haha. I’m thinking of adding a speaker and mic so I can talk to people lol

[@1lovelucas]

I have my first rc car coming in soon, I'll be trying this

[@RECKLESSMOTORstudio]

This one is awesome bro🙏🙏🙏👍🏼👍🏼🤝🤝

[@ChaddRainsFPV]

Thank you! 🙌

[@dronefootage2778]

so the crossfire gives you more range than you need hu? sounds perfect for me

[@petrokey]

Cool! Do you know what protocol does ut use?

[@TheRoadTaken]

Since you offered to answer questions, I'm going to take you up. :) I'd like to be able to flip a switch and have the radio reduce the throttle by say 50% and then be able to hand my wife the transmitter to let her drive it. I've attempted to change the settings but I'm not finding the magic combination. I do have the V2 but I suspect the V3 wouldn't be any different for what I'm trying to accomplish.

[@ChaddRainsFPV]

Hahah for sure 🤙 It’s unfortunate but the v2 doesn’t support dual rates on a switch (possibly after an update- I haven’t updated mine in 2 years). I know how it works on the v3, but v2 you have to get into the menu (number 13) and change it manually every time. Kind of a pain but it’s not terrible 👍

[@TheRoadTaken]

Darn. Okay, thanks.

[@Radiolink_official]

Thanks for your video!!!

[@Gordon-Scott]

Great video and information very well done 😉👊👍

[@crazyoreo9454]

Great video man, i have a few questions, i have gotten hooked on youtube channels like ADHD RC and others and was thinking about buying a long range rc car. So from this video i know that this is the best cheap remote/receiver but what car should i buy that comes with a camera?

[@ChaddRainsFPV]

No cars come with a good camera and video transmitter. We’re stuck building our own for now. I’ve actually got a good how to video for an inexpensive build coming up 🤙

[@crazyoreo9454]

​@@ChaddRainsFPV ok thanks

[@thenerdshow]

I use crossfire with this controller and have a lot of issues with it. The throttle mainly will start going on it’s own.

[@ChaddRainsFPV]

Interesting. I just started to get into testing and haven’t had the throttle go on it’s own but I have had a very touchy throttle for the first 10% of forward pull. I’m going to talk with RadioLink and see if I can get some info on how to resolve this or if there is a possible FW update to get us a more solid system. I’ll make sure to mention this in my next video on the radio / crossfire 🤙

[@Jabiyt_90]

Do you need to buy the cable extension "Needed cables (two of them if getting upgraded AU antennas)" to use this radio in the car?

[@ChaddRainsFPV]

Nope, that sentence you quoted is in reference the video systems antenna upgrade I do on my cars. You may need a specific cable if you want to use crossfire with this radio. Depends on which module you have (if it comes with the cable). But otherwise this radio comes with everything you need 🤙

[@InoymousSpring]

Hi nice video, Im quite a noob and I got this radio today I put it in wltoys 124017 but I notice that my steering is behaving weird like it is turning where it should but its not quite as smooth as i had with the previous stock controller I think do you know maybe what is the settings to fix that?

[@mitchponton]

Would you do a video putting ELRS on that Radiolink pistol grip? ELRS is the hottest thing out there

[@ChaddRainsFPV]

I think I can swing that 😁 I am friends with some ELRS devs and we should be able to work something out.

[@mitchponton]

@@ChaddRainsFPV Badass. maybe a 3d printed piece on one of the radio for something like the following. HAPPYMODEL 2.4G EXPRESSLRS ELRS TX MODULE ES24TX-LITE FOR T-LITE HAPPYMODEL 2.4G EXPRESSLRS ES24TX SLIM PRO TX MODULE FOR X-LITE & TANGO2 BETAFPV ELRS NANO TX MODULE - 2.4GHZ One of the nano modules (since we don't need the size and high power for crossfire because DJI goggle video will drop out before those small tx's lose connection. Honestly it doesn't matter what Radio as long as its pistol grip and standard screen with something like opentx/freedomtx/etc

[@ChaddRainsFPV]

@@mitchponton Getting OpenTX on a pistol radio is the hard part. I use crossfire with a couple different radios as it can auto detect a ppm signal. Configuring of the ELRS tx will likely need to be done via pc, but we can make it work I think.

[@mitchponton]

@@ChaddRainsFPV Opentx or Edgetx would make life easy, otherwise ELRS communicates just like Crossfire so you should be able to set things up on a radio for Crossfire and it works with no issues on ELRS

[@ChaddRainsFPV]

@@mitchponton are any ELRS modules capable of automatically detecting a PPM signal? If so I’ll use one on my ground radio right away!

[@Metaphysicalgrace86]

What video transmitter do you have on the car? That's where I'm stuck right now. I'm using the Fat Shark Scout goggles with a basic AKK BA3 camera ( 60-200MW ) but I'd like to upgrade and get some more range and be able to go around my block like this. 👍

[@ChaddRainsFPV]

My video setup can hit 1200mw so I run crossfire on either the RC6GS or my old Kyosho radio to make sure I have more rc range than video range. But with any analog setup that’s less than 1000mw you should be fine with the RadioLink RC6GS. It has a good amount more range than say Traxxas or Spektrum Radios.

[@danieltrilopez]

Rc Car Guys : I use vídeo 1.2ghz that gives a good range with my RC Car, the problem is that radio 2.4ghz interfere with the vídeo so the solution is Crossfire 915mhz or R9. But now there is ExpressLRS in the market, cheaper than Crossfire and promises really long range. Have you already seen this?

[@ChaddRainsFPV]

Oh yeah I’ve played with ELRS! It’s great but quite a bit different to most rc car guys experiences with radio stuff. It was a bit of a learning curve even for me. After a few more fw revisions I think it will be a bit easier to get into and I can show peeps how to use it, without frustrating 90% of the peeps that try 🤙 It truly does have great range, though I prefer the 2.4ghz version at this time. For 1.2ghz video, I would still choose crossfire at 900mhz, over ELRS 900mhz.

[@danieltrilopez]

@@ChaddRainsFPV thanks Man! At this moment I agree that Crossfire is Still the best system for RC Cars.

[@crowwing9322]

What RC car is in the video picture

[@meanmachinesrcclub]

Hey, great video, thanks for sharing this! I’ve got two questions though: 1. Have you ever tested the Futaba 7pxr for range around your neighborhood? 2. Can you share your fpv setup? I’ve never had this, I mostly speedrun and bash, but driving around like that sounds fun! Thank you!

[@ChaddRainsFPV]

Thanks! I don’t have experience with the futaba radio but I have heard it’s pretty good. I think they use the FSST protocol which I would expect to make it around the block if they have a decent output power (at least 100mw). Here is a link to my best setup if ya wanna check it out! - kzbin.info/www/bejne/gJaVo4aQYrGsarM

[@thelawfamilyproduction329]

Futaba range is horrible for FPV. In Canada it was only able to go out of sight and then no signal. Good for normal RC use

[@HugeBear32]

Hi Chadd, What’s your experience with head tracking fpv? I saw that the new Radiolink RC8 supports that feature, but I’m also looking at using the goggles to also play DCS flight simulator. All this stuff is very new to me and I’m having a hard time finding good FAQs and information regarding inter compatibility. I’d like to keep DJI and also use the goggles for computer simulator/VR stuff, and of course, I’m on a very tight budget.

[@ChaddRainsFPV]

So there is currently no way to use both head tracking and the DSC output for a simulator, as they both use the same port on the radio. You could potentially get a USB to SBUS dongle and use a RadioLink receiver that supports SBUS, to get to your flight simulator. But I have no real experience doing that.

[@HugeBear32]

@@ChaddRainsFPV thanks for the knowledge. btw, my wife digs your videos and voice. Says you need to be a radio DJ.

[@ChaddRainsFPV]

@@HugeBear32 Aw thanks I've been told I have a face for radio too, lots 😂 Hope you guys have a great rest of your week! 🤙

[@paulabriza576]

Im new to rc, would you mind sharing your wiring of this car power sources. Id Like to build one fpv as well but wondering how to power up all components like fan of the vtx, the vtx, etc etc. Thanks in advance.

[@ChaddRainsFPV]

Sure! I’m making a video about it now but here’s some info to hold you over: I power the fan from the receiver, because it’s easy. If I’m running analog I power the vtx from its own battery, because the ESC is too noisy and distorts the video. I normally use a little 800mah 3S pack.

[@rockman49er]

Hmm been waiting a long time for something like this I got lots of rc stuff but my new neighbors ruined my rc car experience called the county on us for dust and diging jumps been here 40 years and never had a problem they moved in a year ago and problem ever since I got myself a losi 8t 4.0 hobao truck buggy to many to mention 5th scale to nitro gas and electric and I can't use them anymore I have neighbors from hell I'm surprised they haven't called on my fpv quads I had the best tracks in my area to huge jumps on 2 acres we live in the boonies to I hate my neighbors ok I'm done complaining lol great video

[@ChaddRainsFPV]

Haha thanks for the comment man 🤙 Hope the neighbors warm up to ya

[@marcsangiuliano4273]

So was it the transmitter, the receiver or the camera and VTX that gives you the long range.

[@ChaddRainsFPV]

It’s 2 parts: The vtx and video RX are super important and so are the antennas I use (800mw vtx and high gain antennas) but the control link did not used to go around the block. So I would have great video and my car would be stuck. This remote and it’s receiver 100% allowed me to get around the block where I couldn’t before 🤙

[@lf5133]

I just setup my Caddx vista on my cheap 2s RC 4x4 it’s fun but the vista stays in “Low power mode cannot record”. Also I only get 25 watts. Would a higher C rated rig get my power up. Is the vista staying low power mode because of the 2s battery? I have it wired direct to the balance lead.

[@ChaddRainsFPV]

So the issue is not the voltage, it’s that the temp control is on, so the vista is looking to be ‘armed’ via Betaflight or a drone FC. You can turn up the power and turn off temp control in the setting of the goggles. Be careful when you turn off temp control, always run a fan on RC car vtx’s 🤙

[@lf5133]

@@ChaddRainsFPV So I got the fan setup, turned off temp. control but the goggles won’t give me access to anything but 25 watts. I also have the 1200w hack but none of that opens up. What might I be missing.

[@ChaddRainsFPV]

@@lf5133 You may need the FCC hack as well depending on where you live. If you registered the goggles in certain countries (and didn’t use a VPN to ‘get’ somewhere like North America, you may be limited to that power until the FCC hack is done).

[@ricardomacias3478]

How do you install your fpv dji unit to the Rc

[@ChaddRainsFPV]

I use four 16mm standoffs, two 60mm fan guards and one 60mm fan, then sandwich the air unit in there and mount it inside the body with the fan extruding air. I can try to get a 3D print to work, but you can check out my best rig video for more details 🤙

[@Top-Jimmy]

Great video Chadd! I need some help mate, I'm in Australia.. I just bought a TRX4 Defender, I love this thing but I went out and invested in a Radiomaster TX12 M II and bought a Ranger elrs module for it. I also bought some 5 channel Radiomaster ELRS ground receivers but have found out that the TRX4 Crawler has a built in receiver and ESC... Now i'm really confused about what to do or how to do it. Also found out that the TX will only output 25mW to the pwm receivers and it kinda sux as ive been looking forward to utilising the power of Express LRS. I also have an 03 Air unit and Goggles 2 planned for video which will also have issues with output power and am stuck as what to do with this built in receiver stuff... any help would be great. Cheers mate

[@ChaddRainsFPV]

You got yourself some projects brother! Here’s some info that I got: You would likely have to change the esc in your TRX4 to use an ELRS receiver. Lots of smaller models come with a 2 in 1 esc / rx these days. I don’t have a power limit at all to the PWM receivers. Possibly on older fw this is an issue? I’m on the latest. I also live in a different region that doesn’t require lbt (I’m not sure if Australia does) so I’m not sure if that’s the reason. I could enter the web interface for the PWM receivers by connecting to their WiFi and change all kinds of settings. Can you get to the full setup web interface by putting /hardware after the 10.0.0.1? (I would out the full url but YT would get me lol) There is an Arduino project for arming the O3. I’m also doing a video on how I do it now. Mine is a bit more expensive and Complicated but gets you OSD (so GPS info like speed, etc). I’ll be making a video on that soon. Way too much info to type in a comment lol. Make sure to have a fan on your O3. Best of luck dude!! 🤙

[@Top-Jimmy]

@@ChaddRainsFPV Thanks heaps Chadd, I will be sure to keep an eye out for your upcoming video mate. Looking forward to it. Your channel is a wealth of information and its really cool how you take the time to answer everyone and genuinely care about helping people. Love ya work buddy. Take care man, MQ4 Australia. 👌👍

[@andrewut7ya511]

I like it. I fly fpv drones but i want to build a car to mess around with. I can do all the fpv stuff, is there a good rc car you would reccomend for around 100 dollars? I would spend more if theres no decent options but i just want to goof around with this thing using spare recievers and fpv gear so 100 would be cool

[@ChaddRainsFPV]

Hmm that’s tough. You want a 10th scale, almost definitely. The bigger wheels help smooth out bumps in the video. I’d say look for reviews on some WL toys 10th scale trucks, my 1/16 car has been a champ but I only mess with it on the smoothest streets, never off-road 🤙

[@EastTactics]

You mentioned it definitely goes farther than your stock, or classic set ups. But… Did it actually make it around your block? If not that’s OK. But I am curious if you did find that it went, what was it 600 m? Also how many meters is that point where most your regular setups Cut out? What is it like 1600 m in a mile?

[@ChaddRainsFPV]

Yup, it made it completely around the block. My crossfire system easily makes it several blocks, but that car has a longer range video system. I will put the RC6GS v2 to the test soon. My other 2.4ghz systems cut out once I get around the corner at the end of my street. The houses blocking the signal will always be an issue but I do expect this radio will do 600m in a wide open field. More testing soon 🤙

[@EastTactics]

@@ChaddRainsFPV Thanks for the reply, good info

[@MrGraeme54]

Thanks for the video, I am really interested in FPV and just getting into it here in Australia. I know this was done some time ago, but I am hoping you can help me out? I am wondering how you get such Clear video signal? I cannot even get half as far without the video being so bad that i have to stop. I would really appreciate some tips.

[@ChaddRainsFPV]

There are 3 tricks: VTX power output (I run at least 1.2w), Antenna choice (I run a super tall antenna on the VTX because the closer to the ground the less effective it will be- I also run X2 air directional antennas on my receiver and point them towards the car) and the last trick is to use a digital system. This last one can be expensive and out of the range for a lot of people but really makes the biggest difference. I’ve been out over a km with my older DJI FPV goggles and plan to get out over a mile soon with my new O3 system 🤙

[@MrGraeme54]

@ChaddRainsFPV Thanks very much. I am currently using a TBS Unfy Pro 32 VTX along with a Lumenier Double AXII 2 Long Range 5.8GHz Antenna (RHCP). I don't use goggles, instead I use a Diversity Receiver. For the receiver antenna's, I am using two VAS Crosshair Extreme. The biggest issue I am having is Static. I am trying to figure out a way to have clear video. Do you have any suggestions?

[@ChaddRainsFPV]

@@MrGraeme54 oh for sure: Power the VTX from a separate battery. This will get rid of noise from the rest of the electronics. Ensure the crosshairs are pointing straight at the vehicle when possible (orient them 50° apart to get the widest beam). Double check the vtx is outputting the max power and is being cooled well enough to not limit it. If possible (and legal in your area) get to a frequency that isn’t typically used. The lower end on the 5.8ghz band typically performs better than the upper end. I like to use raceband channel 1 or 2. Let me know how that goes 🤙

[@MrGraeme54]

@ChaddRainsFPV Awesome!! thanks for the info, I will try that out for sure and get back to you. At present it is summer here and as a reslt it is in the hih 30' s so we are driving at night, to see properly I use ywo small LED spootlights mounted on a roll bar and the camera is a Foxeer Cat 3, which is geat for both day and nighht driving. have you tried driving at night?

[@ChaddRainsFPV]

@@MrGraeme54 Not yet but have some plans to drive out to this awesome camping spot/lake this summer to and will definitely be doing some night shenanigans haha. I’ve got a decent camera for it but it’s for the O2 DJI system and I won’t be able to get the same range as my O3 system. Might have to bring 2 cars hahah

[@dericklong6191]

Can this be used with any rc? The remote ?

[@ChaddRainsFPV]

Technically, it can. There are some smaller cars that have a ‘built in receiver’ to the speed controller. That would require a different esc but yeah, it even has SBUS compatibility so you could hook this up to a flight controller and fly a drone with it lol 🤙

[@jessekormick3796]

How do u use the dule rate 🤔

[@ChaddRainsFPV]

The option to adjust dual rates is number 13 in the setup menu 👍

[@gamerboytaza7619]

what kind of rc car are you using? i have a arrma senton, will that work? what camra should i use? and gogles?

[@ChaddRainsFPV]

Yup, Arma Senton looks dope. Should work fine 👍 I run a Losi Lasernut (big wheels and big suspension makes the video smooth). I have a whole video on how to make an FPV rc car and which system to choose. Should be easy to find and will answer almost everything regarding which system is right for you.

[@gamerboytaza7619]

@@ChaddRainsFPV what video is it can you send me a link?

[@ChaddRainsFPV]

@@gamerboytaza7619 I’m not sure if links work in my comment section, but I let’s try - kzbin.info/www/bejne/nIfdepR6brlkp7c You can also search for “how to build an FPV rc car in 2021” and it’s like the first video 🤙

[@gamerboytaza7619]

@@ChaddRainsFPV thank you it worked. p.s. you have a cute dog 🐕‍🦺what is his name?

[@ChaddRainsFPV]

@@gamerboytaza7619 Right on and thanks! His name is King and he’s about ~1 1/2 years old 🤙

[@MangoJim90]

Hi🙌🖐🏻 What about DumboRc transmiter?) Have you tried it? It also has this 600m range but the receiver has only one antenna 🙂 and it is also a budget option 👍🌄 Thanks!!

[@ChaddRainsFPV]

I have also heard good things about them, but have not tried them 👍

[@upperleftusarc]

I have this radio!

[@Radiolink_official]

It's worthy, alright? haha

[@upperleftusarc]

@@Radiolink_official for the price it works! Just have to figure out some issues with connectivity glitching. May need to try a firmware update.

[@lf5133]

I thought CRSF would be the ultimate. Why r u changing. What do u know that I need to know. Before I buy a better radio.

[@ChaddRainsFPV]

It’s not that crossfire is getting replaced; this radio can work with my Crossfire lite module just like my old surface radio. It’s that this radio’s stock 2.4ghz system reaches around my whole block, so all the people that were asking for a cheaper way to get into FPV rc cars can use this and probably have more RC range than video range. Crossfire is still what I’ll use on my best rigs 🤙

[@ahmadfaris8044]

Hi, do you recommend dumborc?

[@ChaddRainsFPV]

Dumbo is okay, I hear. I have personally not used them.

[@zahriahsaif]

Hai, Berapa jangkauan jarak remote ini

[@daveopie1234]

Why don’t you like crossfire? I would be interested in a range test comparison between this radio and crossfire.

[@ChaddRainsFPV]

I love crossfire, I use it in my best rig. But it’s a lot for some people to set up, and it’s expensive. So many subscribers asked for something less expensive with ‘good’ range and this def is it. Crossfire will definitely out-range this system, but you can plug a crossfire module into this radio’s DSC port too, so it’s a win-win. I made some videos on my crossfire RC cars if you’re interested 🤙

[@daveopie1234]

@@ChaddRainsFPV yes - I saw your videos on using crossfire for RC cars - that’s why I subscribed. I was asking in case you had found an issue such as ground interference or something. Good to know it is still a great option.

[@ChaddRainsFPV]

@@daveopie1234 oh right on! Crossfire has been incredibly reliable even out to 1km, right off the ground. It will still be my go-to for anything that has serious range. I will be testing it out further, I just need to find the proper environment 👍

[@keeganforde2841]

What fpv system is this

[@ChaddRainsFPV]

@@keeganforde2841 Crossfire is an RC link, Not a video link. It’s a module that can be added to the radio in the review. I use the stock 2.4ghz system on this radio in this video along with standard 5.8ghz analog FPV. Specifically, an AKK vtx and a clearview receiver (tho rapidfire works great too) 👍

[@thelawfamilyproduction329]

Thanks for the video! Wish I can use the link, but in Canada and cant use it.

[@ChaddRainsFPV]

Strange, but no worries! I actually don’t claim commissions from any links at this time. Any link I put I genuinely believe is a good product. There is a v3 of this radio out now that I would recommend over the v2 I reviewed. Have a great weekend 🤙

[@thelawfamilyproduction329]

Thanks bud! Keep up the great work

[@thelawfamilyproduction329]

Reporting back. I got the Radiolink RC6GS v3 on the losi lazernut. The range is better than stock, but only around 60 meters of range in the city. Wondering if it possible to do the head tracker and crossfire at the same time with the Radiolink. Most DJI air unit is sold out, and the 03 is available.

[@ChaddRainsFPV]

@@thelawfamilyproduction329 There are plenty of Air Units here in the states, but I can't speak for everyone. I know ProgressiveRC ships to Canada and has a bunch of original AU left. You should be able to squeak out a a bit more range if you orient the antennas well (get them high up if possible). As far as I know, head tracker and crossfire is not possible with the v3 as it uses the same port for both (different firmware to output a ppm signal from the DSC port, or input head tracking signal [probably ppm still], but no way to do bidirectional communication to different devices). Best of luck getting the range you're looking for!

[@thelawfamilyproduction329]

@Chadd RainsFPV thanks for the tips and advice. I will try that website! I wonder if I can extend the receiver cables somehow. If not then maybe I can stick the receiver right in the back for the highest spot and try again.

[@Chris-vc1dh]

do you use recharging bats with this radio or just normal AA?

[@ChaddRainsFPV]

I just use AA for now but I may use a little 3S as I will use crossfire from time to time and it needs its own power anyway.

[@Chris-vc1dh]

@@ChaddRainsFPV will this radiolink be ok with 3s voltage not too much as 6 x 1.5v is 9v and 3s is 12v

[@ChaddRainsFPV]

@@Chris-vc1dh I am 99% sure that is fine but double check the manual before plugging in. I won’t be able to check for a week or so (until I’m back in town 🤙)

[@Chris-vc1dh]

@@ChaddRainsFPV I got this radio today and i have 1.3g video but as the car gets a bit further i get like glitches on the control like the car stops or goes where it wants and i cant stop it, do you think 1.3g can interfere with 2.4g?

[@ChaddRainsFPV]

@@Chris-vc1dh 100% it can. You need a filter on the 1.3ghz vtx. Look up a notch filter or high pass filter. That should help a lot. You can also put filters on the receiver but will need a lot of stuff (u.fl to sma pigtails, correct filters, 2.4ghz antennas). Most people will avoid using 2.4 with 1.3, but you can add a crossfire or dragon link module to the back of the RC6GS v2 if 2.4ghz isn’t working out 👍

[@Chris-vc1dh]

what car is that? what do you think of X Max the big baby?

[@ChaddRainsFPV]

That is a suppppper old Traxxas Rustler lol. I love the X Maxx but it’s so expensive. It might be the perfect rig for an FPV Car 👍

[@scrubbasher6418]

@@ChaddRainsFPV I will let you know as I am just about to dive into a build with my X Maxx. I have a Traxxas Summit with Crossfire and a Caddx system and it works great. I will be looking at including a flight controller so I can get some more OSD as I find I am getting lost driving my rig around the outback in Australia as bushes all look the same. I love this side of the RC hobby and thank you for your video,s.

[@Chris-vc1dh]

nice, what video system do you have ?

[@ChaddRainsFPV]

For this car I am just using 5.8ghz analog, but I normally run a DJI Air Unit or Caddx Vista. I do also use 1.3ghz from time to time but it’s more trouble to set up 🤙

[@Chris-vc1dh]

@@ChaddRainsFPV 1.3g can overlap 2.4g?

[@Chris-vc1dh]

@@ChaddRainsFPV can you put tbs crossfire to this radio?

[@ChaddRainsFPV]

@@Chris-vc1dh if you use a high pass filter / notch filter you technically can use 1.3ghz video with 2.4ghz control. I never do tho

[@ChaddRainsFPV]

@@Chris-vc1dh Yup Crossfire can plug right into the DSC port on the back and it’s all automatic from there!

[@petestarfpv1028]

I use a dji fpv drone that I crashed. Works perfectly no shaking 👌 also that controller is the tits!

[@ChaddRainsFPV]

Ayeee that’s a solid idea! A bit of added latency but trade for an easy gimbal/stabilized camera. Prob has great range too 🤙

[@erlandfpv]

I have this remote but it have defect on the screen 🤦‍♂️🤦‍♂️🤦‍♂️🤦‍♂️

[@ChaddRainsFPV]

Sorry to hear! I am sure RadioLink would like to know about your remote’s issue. You should send them a direct message either on Facebook or email!

[@robert-oq9jq]

Quit with the Hard Sale and just show us it's features and what it can do

[@KVNGSYN]

Can u show a diagram to show how to do it for beginners plz And do u have any social media to ask u for help when am setting mine up

[@stevefox3763]

I have 868mhz R9 long range rc link on my car :)

[@ChaddRainsFPV]

Awesome! Do you know if the R9 module can accept a ppm input? Most need an SBUS or CRSF input, but if so there is a cable you can to use it with this RC6GS radio 🤙

[@stevefox3763]

@@ChaddRainsFPV yes, google the R9M, the module takes cppm :)

[@ChaddRainsFPV]

@@stevefox3763 sweet! It’s way better doing cars with ground remotes. Just need to make that cable and you’re set 🤙

[@stevefox3763]

@@ChaddRainsFPV ahh see I prefer my traditional transmitter, I started rc life with a car and a trigger style tx when I was younger but now fly things and have a high end stick tx running OpenTX and love it. The throttle not being swung loaded to the neutral position would get people at first but car esc's with forward>brake>reverse make things easy, my diy 1/4 scale truck has a esc that is straightforward forward and reverse and that was a little more tricky and I programed in a bigger dead zone in the middle. It is possible to fit the springs required to make my transmitter sprung loaded on the left stick as some counties have the throttle and steering sticks reversed but being someone who flys, it's not something id do to my own tx.

[@ChaddRainsFPV]

@@stevefox3763 Super interesting. I’ve been flying for 13 years now and I cannot make an air remote work for me with RC cars. I like that others find the air remotes nice on rc cars tho. The more people trying the hobby from different angles, the better!

[@abruptlyblunt]

there's no way a 2.4 Ghz radio signal will go that far out of the line of sight, especially around corners with houses and vehicles in between blocking the signal, 2.4 isn't as bad at traveling through walls as 5.8 is but it won't go through the walls of multiple dwellings.......

[@ChaddRainsFPV]

I used to think this too, but look into LoRa. For real. Spend 5 minutes goggling that 🤙

[@choppergirl]

Seriously? Crossfire can go like 30 kilometers line of sight. 2000mw vs 200mw. Radiolink I think is Jumper's "junk" bargain brand

[@ChaddRainsFPV]

Crossfire is def a better RC link, but a lot of the people that are just getting into this don’t have the money or experience to get into crossfire. This radio and receiver allows for enough range to max out the most common FPV video links, so it’s a great option for a lot of people 🤙

[@UmKa-xv8xk]

u need amplifeer. any will do as long as it support same wave lengt . buy one with 8 watt, u will go to the moon

[@ChaddRainsFPV]

Hahah, I did this years ago! But amplifiers aren’t necessary any more. This radio will match the range of most analog 5.8ghz systems, as is. And if you need crazy range, a cheap cable and a crossfire module will work perfect 🤙

[@UmKa-xv8xk]

@@ChaddRainsFPV do u know how many mlw this radio ?like 400mlw?

[@ChaddRainsFPV]

@@UmKa-xv8xk the ELRS module is between 500mw and 2000mw but that power not necessary. Take a look into 2.4ghz LoRa. It has much more range 🤙

[@UmKa-xv8xk]

@@ChaddRainsFPV no i know abour tbs and elrs i fly my self) i mean radio for car .

[@ChaddRainsFPV]

@@UmKa-xv8xk ahh right on. The RadioLink remotes are 100mw iirc. They run a low refresh rate to achieve their range, kinda like setting ELRS or Crossfire to 50hz. It has way more range than any of the other ‘ground protocol’ remotes I’ve tested. But honestly, I use their new RC8X with an ELRS module now. But that’s only because I get over 1km of video range and the RadioLink remotes tap out at around 600m of range in open space. Enough for almost every analog system though 🤙