Losi DB Pro RC Guy Garage Modification To My RC ? Perfection

[@italianstln43]

hi earl watching your videos and rc guy garage gives me the best of both worlds of rc perfection keep up all the great videos.

[@jeremystewart1785]

Those wheels and tires look mean on that very nice little upgrade.

[@orangemound135]

Wzup Mr.Moorehead!!! Great advice 👍 Can't wait until you do the comparison with the rc's. Good match up. Thanks again for your knowledge. Wzup RC Guy Garage!!!

[@HAPPYJACKRC]

2 great youtuber’s

[@rcguygarage]

😂🤣 yes loctite on the video too 😂🤣😂🤣

[@earlmoorhead5555]

Right watch The whole video to know 😂😂

[@jamesgeorge609]

EARL....I made that hex change awhile back,,,,,but interesting enough you can’t use traxxas or armma small wheel nuts haboa has a different thread,, pattern,,,,,fine thread I believe.....🇺🇸👈🚘

[@tomtizumsrc963]

Great video Earl. 🤙🏻

[@benjaminhunt2395]

You could could had put a washer on it so you could have used the stock hex

[@damaylaphoenix1155]

i do that when i get cheap wheels off amazon!

[@earlmoorhead5555]

Yes as I said like the power hobby wheel video but the hex will cut the wheel over time 💯💯

[@juliemiller5740]

Nice video. Going to upgrade mine. It is a great buggy.

[@khrisyeet8022]

RC guy garage can't hold a candle to your channel Earl. When you going to put a Castle Copperhead on that baby Infraction?

[@rcguygarage]

🕯️👍😂🤣

[@Bluecuban71]

Great video 👍 Love the shirts , will be ordering 👌

[@earlmoorhead5555]

Thanks 🙏🔥🔥🇺🇸🇺🇸

[@rcjunkie260]

Sometimes it takes me 2 or 3 viewings or days to watch a entire video,well worth it. I've lost a few of the wheel nut pins. I think its 2mm think? Just dremel a drill bit to size and a little grease or carefully placed shoogoo well keep it in place!

[@galennii4794]

Aaalll riiiiggght got my merch with the dri-fit shirt too👍👍👍🤙🤙🤙🤙

[@earlmoorhead5555]

Nice 👍

[@cadeblain2265]

Rpm skid plates man, also upgrade the steering bell crank to the exotek #1930

[@soundmindtv2911]

You shoulda waited till the end to say they require the different hexes 😂 Love your attitude. I probably wouldn’t have admitted that 🙈

[@williamperri3437]

I still have the stock wheels on there and love that setup. When I tried to put Badland MX 2.8 on they didn't fit right in the front.

[@gamechangerrc4633]

Great video very helpful info👊👊💯💯

[@damaylaphoenix1155]

it look good , but the narrower tire will handle better! try proline PRO1015610 badlands mx

[@TRC2019]

Aaaallllllriiight!! Nice video. When are you uploading some bash video's? I love your bash video's!

[@arrmatuff_traxxasrocks_rc1097]

I put duratrax Mts on my dB pro and they are great 😁👍 and I didn't need to change Hex's 😎

[@adamdatson4646]

Another awesome vid! Rc car garage channel goes alright too

[@dominic9279]

Hey Earl

[@keithcollier9320]

Best upgrade I ever did on my db pro was all metal center diff (same size as lasernut) and aluminum motor mount (same as lasernut) with steel spur gear. No plastic anywhere in the center. With some dBoots hoons, I power slide all over the place. On 4s it runs like a beast! Of course I have fans on the motor to keep it cool. 😎 as 🧊

[@C_J_Edit_z]

Losi rcs are just so cool !!! Sweet mod, nice video👍😁LOSI QUALITY!!!!!

[@lowridr2]

i got a max 8 and the 2400kv motor from traxxas maxx in my tenacity tt pro i run 4s monster monster torque and speed with no temp issues stock was fine but always could be better =D

[@jonvoogd511]

Every video you've put out lately have helped me out. I've got a DB PRO also and love it but I'm not wild about the wheel/tires Rustler tires make a lot of sense. Thanks earl and RC Guy Garage!

[@nofreerides7033]

Yes definitely a nice touch when my stock tires wear down far enough gonna make the switch… guess I must have overlooked RC guy’s vid on this lol … by the way save those front and rear screw and plates with RPM plastic skid plates part # RPM 73182 they work great I also recommend using fuel line cutting to size and using as dampeners… take care Earl …

[@jonvoogd511]

Another question for you is would a vendetta motor work in the db pro? It's got a 130 amp esc a faster kv motor would be cool maybe just run it on 4s?

[@antwon2302]

Hey Earl do you know what they change in the v2?

[@earlmoorhead5555]

I do not 🤔

[@snowpaletehdog]

My buddy has a db pro and those things are really good out of the box and handle so good, wonder how it's going to stand up to the tlr typhon

[@carlosvelazquez4649]

Rc garage for the win, I always watch to the end, I'm always learning being a newbie maybe your experience got you over confident but we are always learning. Greetings Earl.

[@barbedwirerat661]

Can't wait for the comparison video between the DB Pro and TLR Typhon. A highly regarded 1/10 SCT-platform buggy with 1/8 scale buggy dimensions vs a true 1/8 scale buggy. Seeing them compared both on 3S will be interesting; although would also like to see the TLR Typhon run on 4S and then 6S since 3S on the TLR Typhon would disadvantage it somewhat since the 1/8 buggy platform with the more robust build in my view is intended for 4S-6S power.