Low voltage cutoff for battery

[@satishgajini9086]

Sir please share the circuit diagram for LVD(LOW VOLTAGE DISCONNECT) 1.connects the when the voltage >48vdc(load 100 amps) 2.disconnects the circuit when the voltage

[@slaimeris1380]

Is it possible to not use button to reset and instead of it would be auto reset when reaches voltage a little bit higher than cut off voltage?

[@aryajayasuper]

ibwant cut off for 13.5V, how the diagram????

[@NAANsoft]

Nice. I suggest that you add a flyback diode across the relay in order to prevent voltage spikes from the induction generated in the relay coil.

[@terryplank9991]

He did along with a capacitor, I can see it on his circuit but didn't draw it in schematic. Nice little circuit though.

[@MyCaptainX]

He did at 1:18. It's showed for a few seconds.

[@shankarvaigankar8116]

Need input low cut circuit for single phase 5 kva servo voltage stabilizer.

[@enrgysolarandpowerinverter4379]

Excellent work. I want to make a circuit for the 48 volt battery, cut off at 45 volts. Can you help me? Thank you very much. I follow you from Egypt

[@stevemerritt6995]

What value is the capacitor and where does it go ,also what is the diode for?

[@Dc_tech386]

Can this circuit use on high amp draw circuit

[@bikash3003]

whcih capacitor you used ???? ,on line many variable 100uF 25v ,12v etc are availabe ??????????

[@عبدالوهابه-ب4ي]

Hello sir. What is the function of the capacitor in this circuit? Thank you very much

[@AL3X36000]

You can fix the cut off value using fixed resistor value right?

[@shubhamj6788]

Great video! But where is the capacitor you used on the circuit diagram? I see none. If the capacitor is used, can you please tell where and which type? Thanks

[@nevilbarretto4045]

What relay should I use for 12v lead acid battery

[@pac5725]

Hi can this circuit be used for 170VDC voltage cutoff?

[@arnelcope6828]

What will happen after you set the manimum and maximum voltage and then you turn it off and turn on again? Do we have to make a setting again?

[@lawalmohammed83]

What is the output current available for the load?

[@zakirjaan5885]

Sir 3.7 volt & 4 volt tak ka automatic battery charger banaiye sir please

[@obilorodinakachukwu6608]

What if I don't use battery variable. Wen d voltage drops and it cuts off from d load. After sometimes when the battery raises will the circuit come ON.

[@arnelcope6828]

nice video. I think i can use this diagram for my homemade inverter. Thanks bro.

[@Abhishekkumar-mo3pk]

How can we make for 48v battery

[@elliotoriakhi2129]

No capacitor and diode in the diagram but it’s in the practical.. I’m confused!

[@lukaskohout419]

1:17 - there is capacitor and diode in the diagram, left next to relay 100uF and 1N4007

[@candrasniper3404]

There is in4007 diode and 100uf capacitor in the diagram. How could you say no diode and no capacitor? Do you know what is diode and what is capacitor?

[@stevemerritt6995]

Me too

[@stevemerritt6995]

Not on original diagram only appears for a few seconds later on

Where do you connect the led

[@lawalmohammed83]

Will the input voltage be the same as the output voltage to the load?

[@SV-2277]

Same circuit can i sue for 18650 Li-Ion battery of 3.7 and set threshold to 2.7v as cut off, Please suggest

[@malovanyy]

3.6 V is the nominal voltage of a LiIon battery cell. If you cut-off at 3.6 V you use only about half of the battery capacity. For one cell the cut-off should be 2.75-3.1V, depending on the cell model and how many cycles you want to get from that battery. Otherwise nice circuit

[@stevemerritt6995]

The circuit is obviously made for a 1s Lipo which has a storage voltage of 3.8 volt

[@usmanshehu7988]

Am using this not the charge the battery but to prevent my battery from been over discharge

[@iginio3G]

18V (20V MAX) Li-ion battery?,,, 0.5V? ( 16.5V cut-off, 17V & up then reset switch

[@ScinnerNo1]

15V (31V switch 8V cut (-off 24V,,,,,, Battery 11V & down switch 0.7V? I hope that was helpful!

[@usamakhan9315]

dear bro i do not want to use the push button for som automatic purpose can u help me

[@arnelcope6828]

For low voltage protection, 10.5volts for my inverter project.

[@johnnwakanma5522]

This is beautiful, 1000likes. I need this application for a 48volts system to cutoff at 47volts

[@chrisrice683]

Me too! what kind of battery?

[@chrisrice683]

he says just change the relay value to match your battery voltage

[@manjunathapujari9886]

Project is good very good but you have skip the vidio for capacitor &Diode installation with digram also wrong (Not mension the capacitor &Diode in digram )

[@tryingtomake9871]

I need this circuit for charge battery.

[@usmanshehu7988]

Who can list down the components

[@occamraiser]

a relay? Really?

[@aryajayasuper]

for 12V, just change the relay???

[@masterofnothing2125]

excellent brother I need this one

[@muvirimig]

thanks

[@ebikehub9050]

You are great man in world

[@syaifulumam1980]

Thanks a lot

[@TechIdeasAG]

+Syaiful Umam Thank you

[@SolarSolutions2124]

Please lunch in market

[@roopeshkrishna34]

Great..! Thanks for sharing..

[@didiersee]

Congratulations Thank you for sharing. Could you place the translation button on your youtub videos please because I'm french? Thank you.

[@nileshpachunkar8018]

best..circuit.. very good

[@dineshlimbu8117]

Nice..

[@TechIdeasAG]

+dinesh limbu Thank you

[@mohammedsaeed1398]

good bro.

[@Which-Way-Out]

I think the backing track killed your video.

[@TechIdeasAG]

+Laten Braker You mean background music?

[@mohdsohail6091]

9yc dude

[@imanulsaif2001]

Great ! it works

[@terrylay]

Get rid of the damn music so we can understand

[@Rohanblogrk]

16v work yes no

[@m.freestyler8107]

Terrible music in the bkg.