Just finished replacing cartridge, what a wonderful success! Thanks
@TopHomeowner2 жыл бұрын
Fantastic!
@RandyLie Жыл бұрын
Thanks for the video. I followed your instructions with my Hansgrohe system and replaced it with a new cartridge, but 2-months later the pressure has gradually worsened again. Any thoughts?
@user-cj2wt2ku2g2 жыл бұрын
Probably the BEST DIY video regarding this concern. So straight forward and most of all...IT WORKED!
@TopHomeowner2 жыл бұрын
Awesome! Glad it fixed your problem!
@VolleyballJIM6 ай бұрын
Yep, not too long, not too short, covered all topics
@mikealvord554 ай бұрын
Change the cartridge same issue I did put it in upside down so right is on the hot side now. What are your thoughts?
@djmannion23692 жыл бұрын
Fixed the problem. Watched the video a few times and everything was SPOT ON!!! Two thumbs up!!! Thank you
@TopHomeowner2 жыл бұрын
Great to hear!
@deannabailey7408 Жыл бұрын
Great job describing the parts and how to...love to see any hiccups, because in the real world we always have issues, like the part not coming off easily. GREAT VIDEO!
@TopHomeowner Жыл бұрын
Thanks for watching... and for the feedback!
@Salanan2 жыл бұрын
My hot water is suddenly low pressure at every faucet.
@franklinrogers6388 Жыл бұрын
The issue where your pipe connects to your water heater, usually a clr type issue.
@Zackmack91 Жыл бұрын
The issue is likely a blockage. Happens often with galvanized pipe not as common with copper.
@jimjamjom12 жыл бұрын
I have changed the complete shower unit (and therefore also the thermostat cartridge) and yet this exact problem persists (reduced pressure only on hot). Anyone got any thoughts about what else the problem could be?
@aaronbaraiya36922 жыл бұрын
any update? could be your water heater, do you have any issues with that?
@joryclouthier2 жыл бұрын
If you are on a well with hard water or iron pipes hot water tank inlet/outlet could be blocking
@MakaylaTW2 жыл бұрын
i’m having this problem too did you ever figure out a solution?
@jimjamjom12 жыл бұрын
@@MakaylaTW yes, for me it was the water tank in the attic was too small. Had to get someone in to work out the problem.
@kia511 Жыл бұрын
The best video on the topic! Followed the instructions and have hot water pressure again! The strange thing is that my house is 8 years old and we have never used this guest shower, so not sure how the cartridge had gone bad?! Maybe from sitting there without water flowing through it?! Thanks again!
@cabletv1997 Жыл бұрын
Thanks for sharing the video. Question. Could the low hot water pressure from the shower also affect the hot water pressure from the vanity sink faucet in the same bathroom?
@ChuckTownRC51 Жыл бұрын
I did all this and it did nothing. Also, my water takes forever to get hot. This ONLY happens at one shower (and one place) in the entire house.
@i-tit5474 Жыл бұрын
Try this: it's due to the air bubbles in the vertical pipe going to shower head and the sink is usually lower than shower head therefore it (the sink) gets more pressure .what i would do is either run the sink tap on full (Hot line) for a few seconds, you will hear air bubbles coming out once there is no bubbles you can turn it off or you can run both sink and shower ( on full hot lines as well) at the same time for a few second ( it may take longer depending on how far your hot water tank is to both) then turn off the sink tap. i hope that works let us know if it works for anyone. it works for me:)
@flash80512 жыл бұрын
At least a half dozen things that could make this task NOT go as easily as the video shows. Regardless, still helpful...just be aware that it may not be this easy (like most DIY projects).
@gbpluspcrepair Жыл бұрын
Agreed - with my luck, this is never going to be the fix! lol
@anthonymadrigal8851 Жыл бұрын
Thanks for this video 👍 Really appreciate your work. thanks 🙏
@kodaboda242 жыл бұрын
What would be your course of action if this was happening to a shower that the hot water worked in the morning and now it’s not in the afternoon? Would you suspect a cartridge? Home is 20 years old, only this particular shower is loosing pressure on hot our other one is not. We do have polybutylene pipes.
@truth66002 жыл бұрын
Cartridge is pressure balancer, if you have a pressure drop it a no brainer.
@TopHomeowner2 жыл бұрын
Most likely it's the cartridge.
@truth66002 жыл бұрын
I would suspect the cartridge, it floats between hot and cold,in the morning you shower relieving the hot expansion, during the day water heats up expands and gets stuck ,sometimes I have seen little or no pressure from both sides.
@tomacquilano1304Ай бұрын
Brand new shower valve only delivering 2 GPM from the tub spout on full hot setting. Plumbing is all new as the bathroom was gutted and completely new mechanicals installed. The mixing valve is a Moen UT2133EPBN. On full cold from the tub spout I get just over 4 GPM. Spoke with Moen and they say it's not the valve. Any ideas? Thank You!
@1smokeyj350 Жыл бұрын
I wouldn’t check the shower head if there’s pressure with the cold water
@jacobsmith86448 ай бұрын
He said that
@kaltrex9465 Жыл бұрын
Which point in the line to reduce water flow (pressure?) in the shower stream at least, to save money on water bill?
@TopHomeowner Жыл бұрын
They make shower heads that are designed to reduce the flow and save on water
@knicks6030 Жыл бұрын
Quick question what is the pressure from the hot side is not only in the showers I have problems with foists as well.
@jyt-iz6jm2 жыл бұрын
1st time someone tries this and half the cartridge gets stuck or breaks inside the valve. They will be calling a plumbing company. 2nd thing that occurs is the cheap aluminum puller breaks🤣🤣
@bigboybelly15679 ай бұрын
I’m soooo glad I found this video, I could cry ugh
@rscranman2002 Жыл бұрын
Nice video sir. Could this issue also occur in the bathroom faucet? Trickle of the hot water side comes out but nothing when we swing the lever to the cold water side. All other faucets/showers dispense water normally in house.
@bethaiton99162 жыл бұрын
Thanks! Your video helped me change my sister's cartridge. Thank you so much
@TopHomeowner2 жыл бұрын
Thank you! Glad this was helpful!
@timfalter59406 күн бұрын
Yeah the cartridge had nothing to do with mine... there is a mixing unit behind the cartridge that got clogged and had to be replaced. I then used the same cartridge.
@jamesj49096 күн бұрын
Thanks for clear navigation through this repair. Worked a treat.
@kanoelapriel84622 жыл бұрын
Great video. How would I do this with a three knob shower set up?? Thanks in advance.
@TopHomeowner2 жыл бұрын
With a three knob, there will be a separate valve on the hot side that's probably bad. Check out this video for more details: kzbin.info/www/bejne/sHW8Y4B5hr-Fn8U
@davidanderson63042 жыл бұрын
We have a moen brand faucet are the cartridges the same for all brands? Great video Thanks David Anderson Newell iowa
@tonynguyen82482 жыл бұрын
I have new one . I just put in today but the water not strong enough. Can you help me please tell me what I need to do?? Please
@SteelCityFilms2 жыл бұрын
Hi, thanks for the great video. I get perfect cold but when turning to the hot it gets very weak. The entire system is brand new and has never been used before. I have the same set up in the other bath w/ no issues. I have a tankless heater (Navien NPE - 240S). I don't see or know about a manifold. Before buying the tool to remove the cartridge, do you have any suggestions? Much appreciated.
@TopHomeowner2 жыл бұрын
Since it's new, you might just be able to use pliers to pull the cartridge out to inspect it without buying the tool. Also, it could be that the hot water line has some type of blockage inside the line... Like debris from wood or even solder if it's copper pipes. Either way, both hot and cold are mixed in the valve so if something is blocked, or if it's the cartridge, I'd look there first. If it's not the valve/cartridge, then the problem has to be between that shower and the hot water tank.
@patdennis32022 жыл бұрын
hey, i have the same tankless heater, same problem. Did you get it figured out?
@truth66002 жыл бұрын
Replace pressure balancer cartridge.
@truth66002 жыл бұрын
Great job.
@MilkyWayGalaxyy8 ай бұрын
Right after a water main break and repair on my block, my bathroom and kitchen sink hot water stopped coming out, only cold water comes out. But my shower and other bathroom sink are fine. Just my kitchen and main bathroom hot water stopped working at the same time and same day they worked on the main break on my block. So i doubt its the catridge, both faucets are only 6 years old. So is the problem with my hot water heater? But the hot water works for my shower and 2nd bathroom sink??
@user-xh2iy1mw9r3 ай бұрын
Would it be the valve if the hot water is low and the cold is full pressure but when it's hot the water also comes out of the faucet for the tub water?
@lewishorn5628 Жыл бұрын
We had the same problem, replaced the cartridge and still have low hot water pressure in the shower. However, if the vanity sink water is running at the same time, there is good pressure. Any idea on what can cause this?
@i-tit5474 Жыл бұрын
it's due to the air bubbles in the vertical pipe going to shower head and the sink is usually lower than shower head therefore it (the sink) gets more pressure .what i would do is either run the sink tap on full (Hot line) for a few seconds, you will hear air bubbles coming out once there is no bubbles you can turn it off or you can run both sink and shower ( on full hot lines as well) at the same time for a few second ( it may take longer depending on how far your hot water tank is to both) then turn off the sink tap. i hope that works let us know if it works for anyone. it works for me:)
@AboveAllAerials Жыл бұрын
@@i-tit5474 thank you soooooo much for this, I was just about to order a cartridge and saw your comment...after running both the hot water on the sink and shower the hot water pressure in the shower again is good again, you made my day! :)))))
@fictions21352 жыл бұрын
What if it’s the sink and shower only in one bathroom? Hot water in kitchen and second bathroom ok. Hot water in the sink and shower in the first bathroom very low. The only thing I can think is a bad solder job protruding into the copper pipe choking the flow.
@i-tit5474 Жыл бұрын
Try This: it's due to the air bubbles in the vertical pipe going to shower head and the sink is usually lower than shower head therefore it (the sink) gets more pressure .what i would do is either run the sink tap on full (Hot line) for a few seconds, you will hear air bubbles coming out once there is no bubbles you can turn it off or you can run both sink and shower ( on full hot lines as well) at the same time for a few second ( it may take longer depending on how far your hot water tank is to both) then turn off the sink tap. i hope that works let us know if it works for anyone. it works for me:)
@jameswood4303Ай бұрын
I have low pressure in my shower after a water main break
@YungHustle1010 Жыл бұрын
Thank you for this. Definitely fixed my problem. I followed you step by step and now my hot water pressure is back.
@TopHomeowner Жыл бұрын
Awesome, glad to hear it!
@shilver101 Жыл бұрын
had low water pressure in both my showers just started happening out of the clear blue...I called my local water co. they asked if I have a water softener which I do but have never used. They advised me to turn nozzle onto Bypass which I did and water pressure if BACK to normal
@PaulMathews-p4o6 ай бұрын
That Pressure don't look too full :o
@bee2333 Жыл бұрын
Behind the wall if i turn cold off from the valve and keep hot on i get no water on hot at all
@stevenvillarreal6834 ай бұрын
Same here. Any suggestions?
@uncledoey3 ай бұрын
thanks for this before/after presentation. One question--is there any way to tell whether the problem is just the cartridge as opposed to the whole valve fixture itself? The latter is a lot more work and mess.
@tyoder872 ай бұрын
Great video. Fixed the issue but for some reason when the water is turned about halfway between cold and hot, it sounds like it’s struggling to to let water in or something. I heard an odd noise coming from it but only in between hot and cold. All the way either way there’s no noise. I got a Danco cartridge. Could it be just an inferior cartridge compared to the Moen?
@David-ik6yu2 жыл бұрын
Great video. I just installed a new Moen 2510 valve with a new 1222 cartridge. I have extremely low water pressure. If I take the cartridge out and turn the house water back on, the water pressure is normal blowing across the shower. I have contacted Moen and their answer was a new 1222 cartridge. I have now swapped the cartridge 3 times with three different cartridges and no difference. I reversed the cartridge so that H&C are on the bottom. Same issue but now hot water comes out instead of cold. I did recently install a new hot water heater (electric) and pressure tank before replacing the shower valve. Could the pressure tank on the hot water heater be the issue???? All other plumbing in the house works fine.
@TopHomeowner2 жыл бұрын
Both hot and cold are low pressure? Since it's fine everywhere else and you've swapped out the cartridge (a lot), I suppose it could be the valve itself but I'm not sure what the issue would be. Sorry I can't be more help.
@David-ik6yu2 жыл бұрын
Thank you and sorry for the delayed reply. Ill advise if and when I figure it out.
@HugeCockAndBalls2 жыл бұрын
I have the same issue! fuck moen!!!!
@Mashataters2 жыл бұрын
@@David-ik6yu were you able to figure out what the issue was? I'm having the same problem
@jeffmaraman81492 жыл бұрын
Me too just the hot water. I've changed the cartridge and the seat several times...when I remove the seat and the cart water blasts out of the hole
@OpenMindedForever2 жыл бұрын
For a rental unit built in 1928, where the hot water supply pipe is rusted and often clogged, which reduces the hot water flow rate (pressure), would you recommend (1) changing the pressure-balance mixing valve, (2) only the cartridge, and/or (3) "cold water backflushing" the hotline? I get fluctuating 0.05GPM to 1.5GPM hot water from my shower nipple and tub spout compared to 5.0GPM to 5.5GPM on the cold side. It can take 30 to 100 minutes to fill up a 50 gallon bathtub with hot water and I get thermal too-hot and too-cold shocks from the showerhead. Yikes! Old rusted pipes!
@TopHomeowner2 жыл бұрын
Easiest would be to inspect the cartridge first and see if it has a problem, then I'd inspect inside the valve to see if theres some debris that can easily be removed. Good luck!
@truth66002 жыл бұрын
With a rental property, to remove liability, have the pipe replaced,if you take out the pressure balancer someone could get scalded.
@thirteenthgrade5085 ай бұрын
My issue is - mine is a tub/shower. The shower head is fine but the tub faucet when fully open on hot drops in water pressure. Brand new cartridge and shower a tub. Any ideas?
@ferndogg44272 жыл бұрын
Can u just turn off water through body valve?
@TopHomeowner2 жыл бұрын
The cartridge is what blocks the water so once it's removed, you'll be soaked!
@rjdatdude232 жыл бұрын
That’s a nice shower
@astrasasha Жыл бұрын
So i have same shower setup and i had no pressure. But it was because of main valve wasn't fully opened. After opening it more, switching to shower water flow started making noise. Will be performing valve replacement anyways. Watched this video 5 times now.
@jonymanay Жыл бұрын
I only have low pressure on the hot water side. Having issues after replacing my shower head. So the hose and shower nozel part is new. I replaced the mixer last year so its brand new. Trying to think what i can do. I might try the old shower head back on after work.
@cathyfrench3254 ай бұрын
What if you replace the cartridge and still does not correct the hot water flow? Ie still low pressure
@TopHomeowner4 ай бұрын
Most likely there is something blocking the flow. Either something in the pipe (like solder/debris) or possibly a supply line valve is not open all the way
@MicahsMom9 ай бұрын
Ok so my husband replaced the cartdridge because we couuldnt het the water from the tub to stop dripping so he replaced it late night next moeming i went to take a shower turned cold water on from sjower then hot and not hot water turnung jt on only made the cold water slow down what did he do wrong
@willgamez55552 жыл бұрын
Did you have to shut off the water main?
@TopHomeowner2 жыл бұрын
Yes, I did. Once the cartridge is out there's nothing stopping the water
@nicolecamelliti85195 ай бұрын
Can I use the replacement valve you added here on any faucet? I have a Pegasus.
@auniversalwoman Жыл бұрын
So educational! Thank you!
@TopHomeowner Жыл бұрын
Glad you enjoyed it!
@I-Genius2 жыл бұрын
Hello I watched the video , it very helpful. Thanks much, I tried myself, but I got different kind of cartridge. I am stuck. Could you help me if send the picture of my current faucet cartridge, pls
@jasonw471 Жыл бұрын
Looks like the water pressure in general for that shower is very poor at least it would be for me
@onemansvideos21342 жыл бұрын
What if this is happening thru out the whole house
@TopHomeowner2 жыл бұрын
I'd investigate your hot water tank first. Could be blocked there due to calcium buildup or another problem.
@onemansvideos21342 жыл бұрын
@@TopHomeowner thats what im thinking but I'm waiting till spring till I mess with water its currently below freezing temps here in minnesnowda
@onemansvideos21342 жыл бұрын
@@TopHomeowner we had a 40⁰ day last week i turned the main off and turned on all the faucets and turned the main back on to see if I could push whatever it was but I don't think it would have made a difference in the situation since we have full pressure on the cold water and dribble and air with hot water
@aaronbaraiya36922 жыл бұрын
@@onemansvideos2134 any update? We have this issue as well, when I turn the handle to fully hot, the pressure reduces, which happens to all showers in the house
@onemansvideos21342 жыл бұрын
@@aaronbaraiya3692 we had build up it our pipes so we disconnected the main hot from the hot water heater and used an air compressor and blew compressed air thru the hot water side of the faucets and blew chunks of build up out the hot water line at the hot water heater...it definitely helped alot
@Newbrandstudio3 ай бұрын
Excellent video! Thanks
@indymudshow Жыл бұрын
It's not just the showerhead it's also the shower faucet.
@LOREMIG Жыл бұрын
Its possible that all new shower valve has to be adjusted?
@lasaldude8 ай бұрын
Great video man. Thanks. I think this is exactly what my problem is with my shower. Quick side note. Why would any one want tile with a chipped cutedge like that? Was it on sale? Lol it's so ugly. 😂
@TopHomeowner8 ай бұрын
Glad it helped! We think they were going for a Tuscan look when they built the house. It's not too bad but we wouldn't pick it for sure!
@VerryLongName Жыл бұрын
Would calcium deposits limit one or both hot and cold pressures? My shower upstairs doesn’t have as much cold water pressure but has plenty of hot It could easily be a cartridge issue but I’m gonna clean the deposits either way. I’ll also check the valves you mentioned
@TopHomeowner Жыл бұрын
It's possible it's calcium, but that usually affects both hot and cold, not one or the other.
@Isgood2beKing9 ай бұрын
New subcriber, Thank you for your help! That low flow was drive me crazy
@TopHomeowner8 ай бұрын
Awesome, glad it helped you!
@Moomouse669 ай бұрын
Hello! So we replaced this and we are still having the same issue. Any suggestions? House was built in ‘88
@BenMercy5 ай бұрын
Did you try replacing the shower head? There is also a water flow restrictor inside it that you can break off and pull out for more pressure.
@thegirlwithamicrophone10 ай бұрын
SO helpful. Thank you!!
@robertlozano65462 жыл бұрын
How do you check brand of hardware and type of cartridge needed? Thanks so much.
@TopHomeowner2 жыл бұрын
I have another video that can help: kzbin.info/www/bejne/gF6Ti5KglseGfZI
@msbunns16 ай бұрын
Thanks this helped alot
@Tendertroll1 Жыл бұрын
Is the hot pressure supposed to be exactly as strong as cold or is it slightly less strong due to it not mixing with the cold?
@TopHomeowner Жыл бұрын
It should be the same pressure the whole way
@mcnobody6442 Жыл бұрын
Thanks this was my exact problem rust clog at water heater
@TopHomeowner11 ай бұрын
Glad you found the issue!
@emc2968 Жыл бұрын
Can you adjust the cartridge in any way or do you recommend buying a new one
@TopHomeowner Жыл бұрын
New is the way to go
@damien12309 Жыл бұрын
Thanks for your time, I think this will help.
@TopHomeowner Жыл бұрын
Sure thing!
@AnnM2238 ай бұрын
Subscribed!
@stevencaseymiller8376 Жыл бұрын
Comment 69
@ironwill8596 Жыл бұрын
Thanks
@alyshawilborn7491 Жыл бұрын
Nice!!!
@soumilinon Жыл бұрын
@ 1:46 removed two parts(temp. setter) @ 7:21 replaced with one part !!! just saying and @ 7:28 handle not even close to being on properly, really, why not show it now right