Low Water Pressure - Well Pump Problems? Check This First

[@Mark1959Holladay]

Thank you, I'm in my 60's and hung drywall for over 30 years after serving in the army in the 70's so I am not really good in your field. That said my bride and I are deep in the mountains of NC/TN and I did just what you showed..... Praise the LORD I was ready to call the Well folks, you sir saved my bacon and my better half thinks I'm MacGyver so again thank you and you are officially on my subscriptions. Blessings

[@clapinta]

its fine if you just thank the guy that made the video.

[@John-d2c7n]

Very good information, thank you very much. This helps and saves a lot of money for us. Also Mark in Tennessee, we used to live on a beautiful creek in the Cherokee National Forest, Southeast Tennessee, and had to move due to my daddy getting pancreatic cancer and passing away, but we're praying the Lord will help us find another deep mountain property with a creek we can maybe just put a nice camper with a concrete slab and roof over, to come enjoy at times when I'm not preaching here in Central Florida at Hernando Cowboy Church.

[@jljnbj]

Thanks for putting out the clear useful information. With no long introductions. With no music. With no rambling philosophical or political commentary.

[@fredla7353]

So, I have done this several times over my 66 years; but I always read [in the old days] up [now, I simply watched both of your EXCELLENT videos]. I have a two-story home, on a well, 60' away from the pressure tank and well head. My pressure was dropping to ZERO for 30-45secs before the switch kicked on. So, I [checked the pressure tank pressure [as instructed], it was at 35psi. I decided to replace the 50-70switch with a 60-80 Merrill heavy duty. I set my pressure tank to 58psi. I installed the 60-80 switch. It would not cut off. My safety valve opens at 90psi [nice to remember -I installed it 10 years ago]. I reduced the cut in/cut out side by 3 full turns, NADA! I loosened the cut off switch completely, NADA. It would not cut off. Plus my pressure gauge was no longer working [thankfully, I had another]. I was STUMPED! STUMPED ! STUMPED! But, I pulled the pressure gauge, and inserted a stiff 8 gauge wire into the pressure gauge/pressure valve coupling. COMPLETELY BLOCKED by lime/scale due to our very, very hard water. I reamed it out, blew it out, twice. Reinstalled all...WORKS PERFECTLY!! 58psi cut in, 70psi cut off. Which FINALLY gives us decent pressure upstairs in the shower. Thanks for your videos, they coached me along PERFECTLY!! Ps... Next plumbing supplies I need, I will try to buy from you.

[@sushiitron1]

Finally, an informative youtube video that doesn't give you a run-around just gets to the point. 👌

[@SilverCymbal]

I really appreciate that, thank you

[@scooters_scooter]

I agree completely

[@MohGhanem126]

I just installed a pressure tank with the switch and pressure gauge. The pressure tank came filled with air pressure of 60 PSI and I reduced it to 28 psi as I wanna run my pump between 30psi and 50psi. But when I turn the valve on the gauge stops at 20 psi and the pressure tank won’t fill with water. The pump is a submersible one used in a well at 28 m of depth and has 1.5 hp. I wonder if this pump is powerful enough to fill the pressure tank.

[@RandallCarroll-rq5gg]

Couldnt go with out leaving a big thank you here. Our water was sputtering thought the house. Followed your instructions to a T, come to find out I was holding 20psi at my tank. Filled it to 35, all is well. Great video, you just saved me hundreds in having to call someone out, and I learned a lot about my system at the same time. Cheers!

[@jingomeme]

The reason the gauge suddenly drops as you are emptying the tank is that until the gauge drops there is stored water pressing on the gauge, but as it runs out through the spigot it gets to a point at which there is no water left pressing on the gauge. Immediately before that point the pressure that is displayed is the air pressure on the other side of the bladder, but as soon as the water has gone there is nothing pressing on the gauge to register the pressure. It's not "just the way the pressure works" - there is an easily understandable reason! Not meaning to be critical of a useful and well presented video, but it is good to understand exactly what is happening.

[@seriously749]

Clearly stated. Very informative and helpful. Had some issues with my tank today and it’s given me another item to check before having the well company out. Thank you for the clear and informative video-this is wonderful!

[@SilverCymbal]

So glad it was helpful, thank you

[@chrisgarvey2974]

Thank you! Worked perfectly! Wife is very happy to have her water pressure back and that it didn't cost anything ☺ .

[@DonaldSmith1]

Just a note to tell you I followed your youtube video and all came out great. My valve pressure was 21 to start and needed to be 28. It was a great video so easy follow, now my pressure is correct. When you have a problem and don't know what to do, it's so good to find your kind of video instruction. It was in plain easy and to the point, so helpful, Thank you very much.

[@SilverCymbal]

Glad it helped, I love to hear that this helped someone. Thank you for watching

[@warriorshepherd1240]

It’s been many many years since I’ve had to mess with a well system. This video was very helpful in helping refresh my memory of trouble shooting these systems. Thank you! You did a very good job with your video!

[@warriorshepherd1240]

As it happens our went out yesterday and has low pressure today!

[@saintluckyjtr]

Since moving into our new home from a city system to a well system I always felt that the water pressure was just a tad low. Figured there was nothing to be done about it until this video auto played after one of your Great lawn videos. Watched the video and made the adjustments and wouldnt you know we have great water pressure now!!! Only thing ill add is I tried a bike pump first and it made little to no dent in the pressure of the tank so i whipped out the air compressor and that did the trick.

[@andilongmeadowfarm]

I have to say, this is one of the most straight forward DIY videos I have ever seen. Thank you so much!

[@SilverCymbal]

Thank you very much I really appreciate that.

[@ronaldharris5330]

I finally have my well problems corrected after about two weeks of battling the issue. I read through all the posts, and lost some time there in the reading. End result, well is good, well casing good and no clogs ... I touched up the 18 year old pressure tank's pressure ( it was at 24 psig ... increased the pressure to 38 psig and observed it over a few days and is holding OK). Then pulled the also 18 year old pressure switch ... it turned out the 1/4 inch X 6 inch nipple that it was mounted on was completely clogged by hardened sediment. So, because of this lack of a live pressure sample, the pressure switch remained closed and the well would start and run for around an hour, the shut off for about an hour ...it was being started by the closed pressure switch, and would run until the pump's thermal overload kicked it out ... the 1 hour well pump offtime was the time it took to automatically reset this overload on its own, and then restart. New switch, new pipe nipple ... now the pump starts up at 40 psi, and it takes about a minute or so to pressurize my water system to 60 psig and shuts off. It then stays off until water demand reduces system pressure. So, end result of all of this, if you have an older system, or a system that experiences a lot of sedimentation, try checking the piping that your pressure switch is attached to and ensure that your pressure switch is seeing a good pressure sample due to a clear mounting pipe.

[@SilverCymbal]

Thanks for sharing this. Those pipes to the switch get clogged a lot over time. I personally replace that pipe with the switch each time. I like to change my switch out about every 7 years just to be safe and it's cheap and pretty easy to do. You must be thrilled to be up and running again! Thanks for watching.

[@minorm2]

@@SilverCymbal I noticed when I replaced my switches there was a lot of sediment but I only ordered the switches/gauge so I had to remove the sediment with a screwdriver so I could be back and running....but its not working correctly again, do you think it could be sediment in the piping causing my issues?

[@arnelarsen4073]

I’m a municipal plumber, had zero training in well system. Thank you, well explained.

[@jason8283]

Because of your generosity of information I fixed my problem! My pressure tank was a 23PSI. I pumped it up to 28PSI after checking the tank to see if it was full, which it wasn't. Then I checked the pressure regulator. Made sure it had power then made the contacts connected and everything worked. So in the end it was the pressure switch not kicking back on after a power outage.

[@MrJudges4u]

Just look at the number of reviews...a tell tale indication this Professional is a good as can be on KZbin. Another outstanding video for us DIY novices. The certified plumbers and well techs must be scratching their heads.

[@javierruiz2608]

Thank you for the best video on KZbin for homeowners taking care of their wells!!

[@PCBrandt1]

Thank you, you illustrated this procedure so clearly. I hadn't done this for 30 years, I'm a little worried, but my pressure in the shower seems to fluctuate, so i need to do it !

[@jgallone]

Thanks for this video...I checked our tank pressure for the first time and it was at 19 psi and should be at 28 (30/50 switch). I added air pressure to get it to 28. I'll check it again in a week or so to see if it is maintaining the pressure. If not, then probably a bad air bladder and will need to get a new tank...fingers crossed that's not necessary.

[@mattb9664]

A word of caution before attempting to adjust your well tank pressures and draining the water from the pressure tank...if you do not have any filtering or silt filtering (or maybe it's after the pressure tank), while it's closed off to the rest of the house lines, make sure to fill and flush that pressure tank about 2-3 times to clear out all the silt that's in the helper tank. You can tell the silt is mostly emptied when no more clumps of it come out while the water is quickly evacuating from the hose. If you drain it only 1 time to correct the tank pressure while the tank is empty without dealing with the silt, the tank will get stirred up with all the silt like an Ovaltine and let all that silt freely into the plumbing...and each output will require some type of special clean out and tending to get it cleared.

[@gracec1665]

Fantastic video!!! Our well froze over during last week's winter storm and the pressure is super high right now. Thank you.

[@j3o5h8n5j5a3y8]

Great video, but I would add that you can easily confirm the cut in pressure while you are draining the tank. Note at the video 2:04 mark, the click heard is the pressure switch closing. The gauge pressure is 42 psi which is the pump cut-in pressure. That said, there is the possibility that the gauge is not accurate. If the gauge fails to go to Zero when the tank is empty, I would replace the gauge.

[@pjmazar4533]

Very clear and concise video on well pressure. If your system is running with pressure set for 30 to 50PSI, the tank should be set 2 pounds below cut in pressure. That would be 28PSI. In my case, my deep well system runs from 25 to 45PSI for which I need my tank to be set at 23 pounds. It might be worth checking the readings of the cut in and out of the system before draining the tank. On another note, there should always be a shutoff valve to the whole house in case of an emergency. Thanks for the video.

[@danielpullum1907]

A better explanation than two others I watched. My tank is 12 yrs old. It is a WellMate WM-9. I haven't checked it yet and now I know how. I haven't watched your longer vid but will do that now.

[@neilhudson6194]

Guys like you are a saviour to less handy people like me--very good presentation--if the girls can't find you handsome--they should find you handy

[@MrStang9090]

That rings a bell... Red Green?

[@neilhudson6194]

You betcha

[@pzat65]

​@@MrStang9090😮

[@rapturebound197]

Haha... Keep your stick on the ice too!

[@jeremysims974]

Red Green show is the BEST!!

[@jpodlipec]

thank you for posting this.We thought our well pump was out but all we did was drain tank and find the the valve on top had 0 psi pressure. re-filled to 38psi. Everything is working .....for now. perhaps the bladder in the pressure tank has a slow leak but that is for another day. thank you!!

[@markfahrenholz5363]

We have low water pressure. I had a guy check the pressure of the tank, but he checked it when the tank had water in it, not empty. Thanks to your video, I can check the tank properly myself.

[@SilverCymbal]

Thats awesome, I love when people let me know the videos are helpful. Thank you and I am glad it could help.

[@dogge929]

I didn't reach 18 psi when my tank bladder ruptured. If you're new to well systems, GET A PROFESSIONAL! I managed to turn a simple service call into a major repair bill because of this video.

[@longjohnlongdong4692]

Same I think…

[@matthewcalifana488]

On some older homes the small pipe about 5 / 6 inches long is made of steel & can clog with rust ( leads to pressure switch ) , Which I also replaced , Good video ! Thanks Much !

[@SilverCymbal]

😀 If you enjoyed this video please *SUBSCRIBE* and *LIKE* . It really helps keep my channel going and bringing you great videos like these 😀This is the tank I used in this video amzn.to/2mWaF0w

[@kommoncents0000]

For people with a little extra money to spend, I have my standard tank plus I have added 2 larger tanks (all set with the same air pressure, all tied in to my water supply) for a couple reasons. First my well pump does not have to run as much, because I have a lot more water stored, so I am extending the life of the pump. It also enables me to use a pressure washer without waiting for water to be pumped. Another thing I have done is replaced the pump pressure switch with one that has a lever on the side, which is used for 2 things. It is used to prime the pump to start filling the tanks with water. say I had to drain all the water for maintenance. Second it has the ability to shut the pump down if you temporarily run out of well water, which if that was to happen you can burn out your pump motor.

[@lauramejia6909]

Hi.where can i buy that pump???

[@kommoncents0000]

@@lauramejia6909 Are you talking about the pump pressure switch ? My pump is 80 ft below ground and is a submersible well pump.

[@marcoleotta2294]

Did you have to install pressure switches on your extra tanks or did you just connect them in series tia

[@kommoncents0000]

@@marcoleotta2294 You just need one pressure switch, then pipe the extra tanks after the first one with maybe some ball valves and drain valve or two. Check PSI in the tanks when they are empty of water, and most important put the same air pressure in all the tanks, I think its 2 PSI less than the pressure the pump kicks in at.

[@marcoleotta2294]

@@kommoncents0000 Awesome thank you so much.

[@danzohlmann8092]

I'm glad I found this. I had low pressure in my house for a long time. I dont think it was this bad when I first moved in years ago. I finally stated looking at the gauge and my cut in and off was 30-38 to my surprise. I'm gunna wait till Monday to see what my tank pressure is. Your recommendation for increasing the pressure seems to be to get a new switch first. Everything SEEMS simple. I must be missing something lol

[@danzohlmann8092]

Went well ....pressure up. The shower can still run when someone flushes!!

[@charlycostarica8738]

I bought a square D pressure switch. I recommend it

[@ralfie8801]

Dan Zohlmann You can also take the plastic cover off the pressure switch and adjust the cut in/out pressures with a wrench or a screwdriver. No need to change the switch unless it's really corroded.

[@JoeFidler]

Easily the best video on well tanks… I still don’t know what the hell I’m doing but at least I can check the pressure in the tank and for that, I thank you sir!

[@yisoleleranch2828]

Clear, concise, factual and well thought out presentation. Well done good Sir!

[@stroys7061]

I recently paid tuition to the school of hard knocks to learn what you just covered in a few minutes for free! Great video!

[@SilverCymbal]

Glad it was helpful!

[@ron8220]

You can save the cost of buying the pressure testing gauge just by watching where the needle drops quickly when you drain the system. If the needle suddenly drops at 35 psi then you have 35 psi in the tank. Close the drain valve, turn on the pump and watch the needle again. The needle will stay at 0 psi then jump up to what ever pressure is in the tank. If it jumps up to 33 psi then slowly pressures up that is what it is supposed to do. This method realiable enough to give you tank pressure within 2 o3 psi. No testing gauge required. If the drops or jumps up at any psi lower then system should, then get a pressure gauge and add pressure. If the needle drops to 0 psi as soon as the drain is opened or if the gauge slowly pressure up from 0 psi, you have problem. get your tank checked(possibly a blown bladder).

[@helenachase5627]

My tank has no pressure Guage. Go figure

[@MHS_ART]

Omg I’m going to attempt this tomorrow thank you man!! I was so nervous and scared to do this but now I’m feeling good. Thank you

[@thedr00]

This was a very clear and easy to follow video and it answered a lot of questions I had about my system. Thank you very much for sharing your knowledge.

[@SilverCymbal]

My pleasure, glad it was helpful. I will have more well videos and plumbing tips coming soon too.

[@Heimer_D]

Thank you for making this video. Very helpful. Helped me diagnose my tank as having a leaking diaphragm. Water came out of the valve stem when I checked the pressure.

[@juliabattaglia536]

Great step by step video! Helped us troubleshoot our tank, which ended up having 0 pressure. Thank you!

[@richardthomas-ed2hw]

Your diaphragm is blown more than likely replace tank

[@tracyafig]

Thank you! I feel less anxious about causing more harm to my well system AND I can reduce the wait time and stress (ithe well water company has a history of not returning calls or emails). I can rewatch your video and have confidence.

[@AlmaCruz-u1q]

This was great, it really helps us to understand what we are doing. We are new to Indiana and have never been on a water well. now if I can find someone that would help me find my well.

[@Dan-sq7zg]

After the gauge drops to zero you should push on the tank to confirm the tank is actually empty. If the diaphragm has ruptured, the tank won't empty in most cases even though the gauge may drop to zero.

[@fredjenkins8372]

As good a video as I have used. Hit all the high points and talked me through everything I should be looking for. Thank you.

[@thegreatga]

Thanks for making a nice, straight to the point, informative video. I will be checking mine next week.

[@harrylebastard]

For anyone living in Florida especially, it has happened 3 times now where i lose presure the tank was fine and each time the problem turned out to be frogs or a lizard had got fried in the pressure switch blocking the contacts.a simple fix.

[@SilverCymbal]

Wow that is a first for me hearing that! Crazy

[@jerrybaker5081]

Also in Florida even small ants can cause it especially if the switch is outside

[@williambozynski1176]

Check under the lid of the pressure switch (turn power off so you dont get hurt). Under the lid will generally show you numbers 30 50 or 40 60 this is the pressure your switch and system uses. If you need a pressure switch this will tell you the one (pressure cut-in say 30/pressure cut-off say 50) you need to buy. newer ones may have the pressure settings on the cover.

[@mark33545]

is there a way to upgrade it? I just got a new house and the water pressure is not that great and every time I check the guage its always sitting at 30psi.

[@swu7308]

@@mark33545do you find a way to fix it? My gouge is reading 24,I need to fix it and replace it since it’s so rusty

[@leestimson4676]

Great presentation, l got my project tommrow to check my system. Thanks again god bless U Tube and people like you.

[@mastman2315]

Nice easy to understand video. Like most of us when the water goes down we try and check to many thing s at once never isolating the problem So it can be fixed.

[@zippocrow]

Thanks, never worked on one before. Fixed my short cycle problem, I did bleed the system a few times. ( I had silt in the water, I think that was part of the problem) when I drained and tested the air tank I had 0 psi.

[@harrylindanicholson3351]

Every well system must have a Central Shut off Valve that can be quickly used in case of a catastrophic leak like dishwasher or laundry hose breaking. Locate it and tag it. Always wise to change out the hoses to your Clothes washer if they are 5 years or older. Buy high quality hoses. Turn off your water if leaving the house for a day or more. My neighbour had a faucet break while they were away, broke on 3rd floor. 5,500 sq ft home. $250,000+ in damage over 8 hours.

[@SilverCymbal]

Good advice! I thought I was the only one that changed my hoses regularly too!

[@adamwaters5016]

The dad we all needed and never had.

[@RoninJeremy]

Thanks new Well owner, this did save me from calling a plumber / well technician.

[@ElenaPeters1]

Thank you so much!!! I've just fixed my problem following your video! And I've saved a couple of hundred bucks! ❤️❤️❤️

[@brightideas5782]

I always thought the air bladder would get damaged doing this , thank you very helpful 😀

[@donmoore7785]

This procedure prevents damage, by removing pressure from under the bladder. Just don't over inflate and you won't damage anything. If you don't drain the water you won't get an accurate reading of the air pressure.

[@_MP004]

awesome clip! very clear, cut in & cutt out pressure according to the specs of the tank! nice!

[@frednewlin1459]

Of course mine is in the crawlspace surrounded by about five dead tanks abandoned since 1960 to present... I guess they last about 10 years? LOL. Think I’m going to cut an access hole in one of the closets. Thanks for the concise video.

[@MrStatic101]

This was very helpful. My pump won’t shut off because it’s a 30/50 switch and I can’t get above 40 psi anymore. Gonna follow your steps and see if my bladder is bad. Of course no drain on mine.

[@DANIELLE-gq6ct]

Did you figure out what your problem was we are have the same situation going on.

[@MrStatic101]

@@DANIELLE-gq6ct yeah my situation was the tank bladder. I tried to fill the bladder with air but it was done. New tank and it worked fine until the pump went lol.

[@Madcobra29]

I just saved me a bunch of money by watching your video.

[@SilverCymbal]

Thanks for the nice feedback, we can also use money these days more than ever too!

[@alocin110]

Thank you Silver: the video is very informative; good and clear commentary and good tips. I appreciate it. Keep up the good work. Thanks.

[@victoryfirst2878]

What determines the pressure setting on a well system ??? THanks

[@sulibuk]

Simple first. If you have one of those inline water filters that is typically housed in a glass cylinder make sure it's not loaded with sediment. This can create pressure issues.

[@rontruex4177]

Thank you.

[@sulibuk]

@@rontruex4177 Naturally, I hope it helped

[@FrederickDunn]

Nice Job, thanks! Being a Utility/unfinished space, shouldn't all wiring be in conduit? Just curious.

[@SilverCymbal]

Not really sure why but every well around here is done like that. I am sure there are exceptions but it has been the practice.

[@FrederickDunn]

@@SilverCymbal Thanks for responding, I was just going by the NEC, though my issue may be out of date.

[@jayjenkins6021]

Awesome helpful video! I am moving to a house with a well that hasnt been used in a bit. All your info was straight-forward and useful! Thank you! Thumbs up@

[@humanze]

Wow all these years in my house I've only learned this now. 🙏

[@davidcastillo2543]

Thank you for the video, I just checked mine and had to add air, it fixed my problem

[@sotosoto2649]

Thank you for this video. We did these steps because when I ran two facets or 2 or more water sources, my pressure would drop. Our well system is set on 40/60. Our tank would read 25psi, without water so we added pressure to 38psi. But once we turn everything back on, it cuts off at 65psi now. We didnt mess with the switch box....for now we just left it as is...it still cuts on the pump at 40psi.... idk if this will be a problem for me in the future?

[@llamabahama4654]

3 years ago so prob no help now but you can adjust the cut off by itself without affecting the cut on. It's the smaller bolt with the spring usually on the right if you have the springs/bolts facing you. that way you can get to a 20psi window like usual. It's a little weird that is a 25 psi window, not sure if that matters but you can adjust.

[@miyervang9338]

Thank you. You have explained thoroughly. You have save me money and time today. Thank so much! I appreciated your video.

[@jasminnarain1911]

Great video . Clear and knowledgeable. Thank you so much for your kindness. Deeply appreciate your time and knowledge . Make more videos.

[@SilverCymbal]

Glad it was helpful!

[@brodheadjim]

Very helpful. Nice to be able to start the process before calling the plumber.

[@YukonHawk1]

I have the same exact tank as you that is still going strong after19 years that was installed by the second owner of the house. I'll be checking my tank tonight. Thanks for a great video. I just checked my well tank and unfortunately I do not have a shut off on the main supply coming from the well.

[@floreserick77]

Thank you. BIG Help I was about to call a plumber. Saved me some $$$

[@SilverCymbal]

Thank you SO much for the comment i really appreciate it. Glad it helped.

[@ibanez2010]

Thanks man! Flicking the contacts worked. Whew. Saved my night.

[@virginiajoanprange8102]

Thank you for your input! We will try this before ordering a new pump!

[@jimdezieck7743]

terrific - wonderfully produced, filmed and explained. thanks!

[@SilverCymbal]

Very kind of you thank you

[@veronicabiggs3407]

Great Video, how do you know what your cut out and cut in pressure should be and what determines it?

[@catchingupwiththecooks1078]

look at the rating on your switch, inside the cover, and your tank should match it

[@kinglou480971]

Another GREAT job of explaining. One question: Why does the tank have to be empty to check the pressure?

[@wb3161]

Because if the tank is filled it will change the air pressure. The more water is has in it will increase the air pressure. So you need to check the pressure of the tank with no water inside pushing against the bladder

[@coreymcconnell1908]

Great video. I just purchased an acreage with a well, this was very informative. Thank you.

[@leoayoroa7217]

Thank you so much I’m new to the system and learning as I go and this helped out tremendously

[@paultherrien9422]

Thank u for good information and no BS

[@traviansmith2262]

Man I want to THANK YOU FOR YOUR INFORMATION!!!! It really help me… thanks sir

[@creativesoftwareconceptsin124]

Thank you very helpful - can you explain why the pressure tank air pressure should be set to 2psi BELOW the Cut-In pressure and what would happen if the Tank aire pressure was pumped up to 5 psi ABOVE the cut-in pressure?

[@dennisrudnitski-zf7dn]

Excellent video clear and safe well diagnostics .

[@MrStoney61]

Superbly explained. Thank you.

[@charlesreese9085]

thanks for the advice. real easy to understand.

[@sarahwatson7692]

Twenty psi between on and off. This is wonderful when showering as the water goes from high to low. Set it so when there is flow the pump comes on and stays on as long as there is flow.

[@ralfie8801]

Sarah Watson It doesn't work that way, most well pumps will pump more water than your shower head can flow, so it's still going to fill the water system and shut off until the pressure gets low enough to turn it back on. I need 3 water hoses running sprinklers in the yard to make my well run almost continuously. That's at least 3 or 4 showers worth of water on my system.

[@donmoore7785]

No, you are incorrect. Your pump does not need to be on the whole time.

[@Samlol23_drrich]

Your videos are fantastic. Thank you for making them. I’m having trouble finding specific parts for my system- maybe you can help. I have 1 inch polyethylene coming into my house, with what appears to be a 90 degree plastic adapter.the 1” side is a barbed fitting held into the polyethylene with some ss clamps. The other side of the 90 degree adapter is 1 1/4” MPT and goes into my check valve. I cannot find a replacement adapter. Might you have an internet source for well parts you can recommend? Most plumbing supply places have a straight adapter, but not an elbow, and I am looking to make as few connections as possible. Thanks again for these great videos.

[@qizan8065]

Thanks for the precious lesson ❤

[@josephmorningstar3272]

thanks...I hope this works

[@wendystotts4899]

Instead of turning the valve off to the house my husband instead emptied the water lines in the house & didn't empty the tank. Now we have no cold water pressure in 3 sinks & a bathtub.

[@kennethmelendres7401]

Great video, was able to use your tips just now. Thanks a lot!

[@SilverCymbal]

Glad it helped!

[@curtchase3730]

So close to a great tutorial, but missed the mark in many places. You should have explained symptoms that would point to a problem withe the storage tank. Explain what goes on in the tank and why pre-charge is very important to the life of the pump and tank. Why you set the pre-charge air pressure 2Lbs lower then the cut-in pressure. What happens if it's too high. A diaphragm tank that has had near zero pre-charge for some time is usually toast. Surging water pressure is a good indication of a failed or low air pressure in tank. Why did bladder storage tanks supersede old pneumatic tanks? List goes on. I'm NOT a well guy or a plumber! Just lived my life around well water and learned as life went along. BTW, that install is real nice. Liquid filled gauges? Wow. One thing I always do when installing the pressure GAUGE, is perch it up on a 3-6" nipple. I believe doing that keeps water from entering the workings of the gauge movement which can cause early failure.

[@toneman8478]

Could you do a video tutorial on what you mentioned and include information about the actual pressure switch

[@EzequielMaldonado-f4d]

In changing the pressure tank can you change it for a smaller tank or bigger tank ..or vise versa ....or do you need the same pressure tank...I've wanting to change mine for a bigger one. Would it be OK for me to install a bigger one

[@gial8862]

Bigger is always better. Puts less stress on your pump. Pump lasts longer. Bigger tank costs a lot more though up front. Also, go with stainless steel Union Tank Tee assembly. It will make all future maintenance a breeze.

[@terryblais9128]

Thanks for sharing your knowledge very well explained. Happy Trails!

[@omidahi9767]

It was wonderful tips you saved my weekend thanks

[@earthling7355]

Nice demo. Won't be able to apply it for a couple of months yet, camp is not going to be accessible until May or so.

[@jesusgrl11]

Such a great and informative video! Thanks so much for your knowledge!

[@judykerr5312]

Thank you for the information . Very good video, simple and direct.

[@Random_Innovation]

thank you for clear and concise information.

[@gial8862]

Should cutout pressure always be 60 if the cut in pressure is 40? Would cutout of 70 psi put the system at risk?