This video shows how to disassemble, inspect and reassemble a Constant Velocity (CV or Birfield) Joint. If we can ever assist you in any of your off-road needs log on to www.lowrangeoffroad.com or call us at 801-805-6644.
Пікірлер: 250
@ruslan26769 ай бұрын
Simple and straightforward, very good tutorial 👏👏👏
@endurofan98543 жыл бұрын
a very clear and straight forward tutorial sir... the best video i've seen regarding CV joint 👌
@lilrome204 Жыл бұрын
FOR SURE HELPED WHEN DOING CV AXLE BOOTS ON PORSCHE, AUDI AND VW
@JnksFINRG Жыл бұрын
Superb video, did my first CV rebuild with help of this one and everything went smoothly. 👍
@ChannelConnect823 жыл бұрын
I'm trying to do the same job, gonna be very helpful in the process of getting the job done. Thanks for video 👊
@crazyDIYguy2 жыл бұрын
I always knew my ride has balls of steel.😆
@Nemesis27475 жыл бұрын
Saw this video last week and what i learned from here saved me yesterday. Replacing the axle on my Audi i removed a ziptie holding on the inner joint too early and the balls started falling out when positioning the axle. Cleaned and greased the balls and put them back in saving me a headache.
@pragasamsupiahs84193 жыл бұрын
Good job sir.Thanks for the Video.greetings from Malaysia. 😊😊
@trinifirst67025 жыл бұрын
It's good to promote rebuilding rather than replacing.
@CHEVYK104 жыл бұрын
A lost art in this world
@crxdelsolsir4 жыл бұрын
Throw away society all in the name of greed (but disguised as efficiency and warranty security). Manufacturers = Financially Wins as it gets to sell you more than you need (whole assemblies) increasing profits Mechanics = Financially Wins by having a higher Profit margin on top of more expensive whole assemblies. Wins again as the fix is faster (ensures profit consistency per job). Customer = Financially Loses due to paying a lot more for buying whole assemblies. Environment = Loses due to more pollution manufacturing and more pollution as land fill
@eze8024 Жыл бұрын
Today's society is too quick to throw away and buy, instead of fixing.
@danielschubert4958 Жыл бұрын
As a mechanic while I agree rebuilding is a good thing to know how to do, in certain situations like cvs it’s usually actually cheaper for the customer to replace the unit rather than getting it rebuilt so to the extra cost of labour spent rebuilding. If doing it yourself then definitely rebuilding is much cheaper
@mawabethel5 жыл бұрын
very informative and skillfully presented, Thank you #lowrangeoffroad. Love from Vanuatu
@pablolopezparrague4995 жыл бұрын
Thank you!!! Great video
@liamjhewitt13 жыл бұрын
You probably saved me at least a couple of hours there, cheers
@artnoll5 жыл бұрын
Great video, great voice over. Think I would try this on somebody else's CV joint before mine.
@budhihart81615 жыл бұрын
In indonesia..we fix cv joint....by recondition the cage....and the sound gone away....and only for 6 dollars minus the boot
@PUBLICIDADECOS3 жыл бұрын
@@budhihart8161 How do you recondition the cage?...
@budhihart81613 жыл бұрын
@@PUBLICIDADECOS if the cage is symetric .just reverse it..put inside to outside.. But if not..then just weld and re shape the inner side of the cage with grinder
@PUBLICIDADECOS3 жыл бұрын
thanks, @@budhihart8161
@PUBLICIDADECOS3 жыл бұрын
Thanks, @@budhihart8161 ...It will be great if you make a video of that recondition :)
@richardperry41153 жыл бұрын
Very helpful, at this moment I’m doing the exact job on my Daihatsu fortrak . Many thanks .
@knightrunner1667 Жыл бұрын
where did you pick up your rebuild kit for this buddy
@richardperry4115 Жыл бұрын
@@knightrunner1667 Milners in uk . 🇬🇧
@dixonmarrah75644 жыл бұрын
Hi low range garage, we do follow up all your tube videos me and my younger brother. Me and my younger brother we a garage on our own. But Your healthy support towards tools. like Jack stands, air wrench, hub seal tools etc. With thanks.
@stoker203 жыл бұрын
I'm surprised no lubrication was used!!! Very interesting. Replaced an outer boot on my Honda today. Someone warned about balls falling out but that was never a worry for me. Must be worn as hell if the balls fall out. Mine was almost as tight as that one.
@ianholden52368 жыл бұрын
I wish I saw this yesterday I just put my axle back together and was wishing I knew how to pull the birfields apart hahaha
@irshadashraf79457 жыл бұрын
very technical video basically i am Machanic
@mwevurasalum46953 жыл бұрын
What about grease no needed when installing the ball
@vinny69353 жыл бұрын
This is great - thank you so much for sharing this video!
@kamrynfinn12482 жыл бұрын
Sorry to be off topic but does anybody know a trick to get back into an Instagram account? I was stupid lost my login password. I would love any tricks you can offer me!
@gusrohan98682 жыл бұрын
@Kamryn Finn Instablaster =)
@kamrynfinn12482 жыл бұрын
@Gus Rohan i really appreciate your reply. I got to the site on google and Im trying it out atm. Takes quite some time so I will get back to you later when my account password hopefully is recovered.
@kamrynfinn12482 жыл бұрын
@Gus Rohan It worked and I finally got access to my account again. Im so happy! Thank you so much, you saved my ass !
@gusrohan98682 жыл бұрын
@Kamryn Finn happy to help :D
@khimsophacarfixing3 жыл бұрын
This is a good work. I like it.
@DOCTOR64236 жыл бұрын
extremely professional way to teach.great job. from Pakistan
@estbiker3 жыл бұрын
Very helpful video!
@katlegomohlala55453 жыл бұрын
I still feel nothing beats brand new. But very informative
@JahvaBonner4 ай бұрын
Thank you so much for teàching❤ God bless you sir
@FiliposM32 жыл бұрын
Thanks for that... Few days ago I pulled apart my whole driveshaft from a '99 Toyota, and couldn't assemble back an outer CV joint, because in the inner CV joint I had to insert these balls from inside and I thought that it is the same on the outer CV joint, lol. Thanks again!
@TomTom-up1kz4 жыл бұрын
Very good job 👍
@DOCTOR64236 жыл бұрын
great video.good luck
@devilalsuthar1772 жыл бұрын
नमस्कार मे आपके ईस काम से हमें बहुत सिख मिली
@uduakedet47964 жыл бұрын
Good to see people
@amana14803 жыл бұрын
Does it matter if the balls go back in different positions compared to how they were removed?
@OSCARANDRES0392 жыл бұрын
How do you remove the spline shaft from the rased??
@bstevenson10025 жыл бұрын
Perfect.. thank you
@hatemalfiqi45827 жыл бұрын
big like Thank you
@TomTom-up1kz3 жыл бұрын
Very good job thanks for you 👍👍👍👍👍👍👍👏👏👏👏👏👏👏
@macloviomus42464 жыл бұрын
Nice video tanks for that
@tnamen13076 жыл бұрын
Sir, my car CV axle has a play and make sounds on both sides of the front car. I hold the CV axle firmly, pushing in and out. During this time, the axle makes a play movement about 1 cm with a bit of click sounds. There are no leaks or signs of worn in the bushings or rubber parts. Is this normal? And any danger in driving with this axle play? Would be please to hear a good solution Thanks
@ariftoygar15567 жыл бұрын
Thank you.
@jakobat19947 жыл бұрын
thats a nice looking hammer you got
@lowrangeoffroad17 жыл бұрын
Custom made lol
@nizamiqurbanov89616 жыл бұрын
Recros Recr
@jacksegond71632 жыл бұрын
Good vid for half the job. Would like to know how you separate the rest of the cv tho? How do you get the long shaft out?
@cassimdangor65787 жыл бұрын
Thank u I hv learned a new task
@RKubernac7 жыл бұрын
Thanks for the video definitely helped me but one question I have is would a brass punch and hammer be a better choice? Watching you installing it by hammering on the ball with a steel punch, did it not leave a flat spot?
@lowrangeoffroad17 жыл бұрын
That is a good question. These parts are super hard. We took this joint apart several times with these tools and there was not sign of any damage at all. We have tried brass and found that brass flakes and chips off leaving little pieces of brass inside the joint and they are almost impossible to clean out. So we recommend using steel tools. Thanks for viewing and commenting.
@ericdixon28986 жыл бұрын
I installed some outer wheel bearing races into a brake drum with a hammer and punch. Ruined my punch.
@armandog.damato81936 жыл бұрын
Exacty. IMO, for this job soft steel tools are the best.
@bnellynel4 жыл бұрын
I use hardwood dowels they work very very well and no shavings no scratches at all.
@longobardir3 жыл бұрын
use a nice solid chunk of UHMWPE plastic
@adeelautosworkshop373 Жыл бұрын
Very informative great
@firoznanji17712 жыл бұрын
Very Very Good, Thank You
@garrisonk86275 жыл бұрын
is it possible to install the race upside down in the cage? i rebuilt my cv joints on my honda s2000 and there is a humming noise coming from the drivetrain now
@sisilsuranjan50197 жыл бұрын
thank you
@robworrall68323 жыл бұрын
That was excellent but what about types of grease and how to pack the CV properly?
@mackoytvkuntingkaalamancha34912 жыл бұрын
Nice job sir
@jameswah54585 жыл бұрын
I Think you are a supper star. Can I ask a quick question . I bought a new CV join all shape and size are identical same amount of inner teeth but the teeth/grove slightly different shape the new one it had a v shape grove instead of a U shape grove and it seen 2mm smaller to fit to the main shaft. will it be ok to remove the old internal into the new one with the new bearing. The old CV join make click when turning corner as the rubber cover was damage with unknown time. any help thanks in advance.
@abdullahvetran85975 жыл бұрын
Thank you. For your steps . That is veri good.
@mahmoods98612 жыл бұрын
Hi, if the cv axle joint, wheel hub side, almost seized, is it still good to repair or cv axle no good anymore?
@havelpants5248Ай бұрын
My question is, if a cv joint is mishandled and comes apart inside the boot, can it be reassembled whether the boot is left on or not? Or was that something that would damage components and need them replaced?
@wilE67645 жыл бұрын
my problem is getting that bigger part off the vehicle..any suggestions...i heated & tapped it cant get it off..thanks
@TheThelocalboi5 жыл бұрын
tks udb!
@specialtymachining6 жыл бұрын
Shaft is retained in constant velocity joint by circlip; drive joint off shaft.
@ssmwalker5 ай бұрын
Hi guys. Great video. However, what I don't understand is that when pulling apart a good working VB join / Birfield, the whole thing moves around nicely, but during re-assemby the Birfield seems to be very tight. How do we get this re-assemblrf Birfield to become as loose as the original?
@nimalasirirandombage59664 жыл бұрын
Won't it damage when tapping on the cage and the bolls at least even little bit. isn’t there any other way to push this balls in ? somehow this is very very excellent explanation and very clear sound and expressed it in attractive manner .
@Abu-Rubeen2 жыл бұрын
Helpful 🙏🙏
@jessjohn61574 жыл бұрын
Why isnt anything being greased before assembly?
@alivevanhelsing.24055 жыл бұрын
Молотом по шарам это круто респект.
@narancs55 жыл бұрын
Why are you not using any grease in the assembly?
@ricardoilagan517411 ай бұрын
Nice video but why didn't applied the grease before re-install the parts?
@teejays25533 жыл бұрын
All parts lightly oiled, brass drift and Soft hammers of various materials ?
@longobardir3 жыл бұрын
Yeah like really? Wtf? I thought I was bad. "the punch is just ever so slightly softer than the balls and cage so lets beat it in with a sledge."
@mohamnademtiaz99363 жыл бұрын
Thankyou very much...
@ariyarathneachala62342 жыл бұрын
Thank you
@670trex6 жыл бұрын
What grease did you guys used?
@jorgeestay28025 жыл бұрын
Excelente
@stevewrenches9 ай бұрын
Yeeeeeeees!! I did it 😍
@rocioguevaraobando90756 жыл бұрын
gracias
@sportman40005 жыл бұрын
Do you sell CV joints for Subaru? If not can you recommend where I can get a quality one without going OEM?
@papabits57213 жыл бұрын
It’s easy! Just call local parts store get and install new one.
@Interventor-xn5bs Жыл бұрын
Excellent video ! In Brazil, CV joint spare are not sold...
@josepeixoto33845 жыл бұрын
Nice video,still i would do 2 things differently,i would grease the parts before the assembly,and i would use a 1/2 inch brass punch.
@zimarokas5 жыл бұрын
Good thats the right way
@ryanvf214 жыл бұрын
@jose peixoto yes
@isaakwelch34514 жыл бұрын
They mentioned that brass flakes off while doing a job like this
@mamunahmed22126 жыл бұрын
very good
@ibharchanda39492 жыл бұрын
Does that mean the bearings and other inside components were not worn out?
@luthandolaw23012 жыл бұрын
Perfect 👌
@sradowazyszczadoniecki65673 жыл бұрын
why this joint doesn't move after he rebuilds it? in the car you will also use a hamer to turn steering wheel?
@bob82pigdog7 жыл бұрын
Where did you source the cage and balls by themselves? Is this an OEM joint you are working on or aftermarket? Great video! Thanks!
@lowrangeoffroad17 жыл бұрын
The Joint and rebuild parts are manufactured by RCV Performance and available from WWW.LOWRANGEOFFROAD.COM. Thank you for watching and for the question , If you have any other questions let us know at sales@lowrangeoffroad.com
@Okey_dokey Жыл бұрын
I was taught not to hammer but is it okay to do it on cage?
@najawassolls2434 жыл бұрын
Where do i get balls and housings? Here in germany it isn't common to repair like that although it is a great thing. I think that probably the work time is to expensive. If you search here at the auto part dealer you can only buy the whole axle. In some cases you can get the joints solo. But i don't know where to find balls, cages or other parts solo.
@mamerismail71174 жыл бұрын
merci
@ChavezDIY4 жыл бұрын
Thanks for the video. Are the balls and cages inside the CV joint universal or are there specific sizes. I want to rebuild my Honda axle.
@isaakwelch34514 жыл бұрын
I'm pretty sure it varies. My daytona's axle only has three balls, not six, like this truck cv axle has.
@deshmitter57173 жыл бұрын
Sir i dont find this hammering mathod to dismantle ihe cv joint is a right way as it can damage the balls and ball race too.
@aogondavid3382 Жыл бұрын
That's great
@user-ml2tp8no6m6 жыл бұрын
nice
@orlandchannel1438 Жыл бұрын
Great New friend
@mimiporsche6 жыл бұрын
Excellent explanation !! can you do it with all kinds of joints on the market? thanks ☺
@mimiporsche4 жыл бұрын
@Mr MEMé me lo scrivi in italiano o in francese perché non capisco l'inglese?
@ashokrajkumarrajkumar2832 Жыл бұрын
Useful
@CampTlangram Жыл бұрын
Mine outer bearing racer was broken.New assy of CV joint axle cost almost eighty thousand Indian rupees in India.Only that outer bearing racer/cone is what i need. Can you help me to find what i need for my truck Tata 407 4x4.
@just1life9057 жыл бұрын
that's alot of work..
@CHEVYK104 жыл бұрын
If you're lazy
@saijuakshaya19832 жыл бұрын
Supper👍👍👍
@prabhudeva70045 жыл бұрын
i worked birfield manufacturing industry i need more knowledge abouts this cv joint i need some basics of materials types manufacturing methods and new models so u tells what are thing to refere to take full konoweldge about them
@robe94678 жыл бұрын
quando rcw metterà in produzione una trasmissione dedicata a vitara?
@user-py1hz9ik2i3 жыл бұрын
it is necessary to lightly lubricate the parts before assembly, and not drive the parts with a sledgehammer
@haithamsaadaldin44625 жыл бұрын
رائع
@oldrockandroller7682 жыл бұрын
Never use a steel hammer.
@mehdikashfi57615 жыл бұрын
Good
@juanbarrientos31745 жыл бұрын
Por que no suben de marcas mazda 323 y 626 ya k no ay vidio de.esos veicuños se les agradese
@user-ft5fh2uj7d Жыл бұрын
При сборке все смазать нужно слегка
@ronplucksstrings71123 жыл бұрын
Looks like a decent informative video, and all the other comments are positive, and I'm no AWD expert, but does anyone else cringe when he hits the bearings with a (hard) drift...shouldn't that be with a brass or alu drift?...the hammer didn't look especially "soft" either!
@Kogacarlo3 жыл бұрын
I disassembled and cleaned my joints and put them together without tools at all.
@gooburrum2 жыл бұрын
@@Kogacarlo Same here. Fingers did it all. I wonder if some cv joints are different?
@Kogacarlo2 жыл бұрын
Now that I think of it I have to say that my CV joints are 32 years and 280000 km old. New joints may be very tight and very hard to work with. I don't know to be honest.
@alexmurphy6442 жыл бұрын
Soft hammer….pulls out a steel mallet
@wesfields9322 Жыл бұрын
@@gooburrum care to do a video?
@mannatchauhan93327 жыл бұрын
are these repaired axles are reliable...
@lowrangeoffroad17 жыл бұрын
Yes, as long as the joint (balls, cage, race and housing) do not show wear. One of the main indications that a CV joint is worn out is that it will make a clicking sound while accelerating in a turn. If this is observed the joint is worn out and should be replaced. If there is no noise in turns and the only thing that is bad is a torn boot, the joint definitely can be disassembled, cleaned, reassembled and re-lubed. It does take more time, but depending on the cost of a new drive axle (or joint), it can be worth the effort. Thanks for watching and commenting.
@yalgret5 жыл бұрын
Wears gloves, but the CV joint is perfectly clean 😂
@FatBat5k4 жыл бұрын
It's to keep all the blood in when you smash your hand with the hammer/chisel