M113 engine rebuild - Part 13 - Cylinderheads + Camshaftbearing Bridge Installation

➤Don't forget to subscribe ! bit.ly/SubscribeJMSpeedshop
➤Patreon: / jmspeeddshop
➤Website: jmspeedshop.com
➤instagram: / johanmuter
M113 Cylinderheads Camshaft Bearing Bridge Installation
Got the cylinderheads back on the engine's on both sides. also the camshaft bearing bridge is installed. Cam sprockets back connected. chain Tensionair back in place. And the crankpulley mounted and torques
To put the heads on, there is a small seallant line needed around the cylinderhead on the outside and around the coollant and oil ports. But "not" around the cylinderbushings them selfs.
Normally when you got a headgasket there is on some placed some seallant. But with Mercedes this is not the case. In the manual there is standing there is seallant needed on disorted or corrosion spots.
But on my old gasket there was on much more places seallant and im not the only one that has seen this. There a more people with rebuilds on the m113 that have this. So i applied this on both sides of the headgasket.
I have put the head on torque using the oem sequence but a different amount of torque because of my new headstuds that im using. The final torque firgure is 110nm and done this in 4 stages.
if your interested in a set of headsuds follow this link
These camshaft bearing bridge need to be mounted equil with all the bolts in and the screw done. All the bolts need to be renewed.
When putting the head on the block it helps to but the chain tensionair in for the moment because placing cyl 1-4 heads is easier. After this pulle the tensionair out again
When the heads are on the block the sprockets can be mounted on the cams. Now these are on torque the tyraps can be removed from the cams. The chain tensionair can be put back in and put on the richt torque setting.
Also the crankshaft pulley need to be put on torque this needs a massive 200NM and then a 90 degree angle.
Finally checking if the timing is correct. Turning over the engine 14 times and the marking on the cam sprockets need to be back on the chain marking. Also the crank pulley needs to be on 40 degree s
Also have a look to the other rebuild video's of this engine
JMSpeedshop.com
MUSIC: Rewind By Markvard

[@giopirmisashvili5514]

Thank you

[@selimcanavsar8702]

This build is awesome too but I am still salivating over V12 w201

[@BizzyVlogs]

Coming along nicely. Looks like you will be starting it soon!!

[@JMSpeedshop]

Engine is almost ready but i have to do the complete fuel system. And engine wiring. . But also the hydraulic system from the rear suspension . But i will get there soon

[@RichardE3046]

En al dat werk gewoon even thuis in de garage, super!

[@JMSpeedshop]

Dank je wel

[@trevorgreenwald4043]

I have the m112. Do you know the torque pattern for the head bolts?

[@thepio14343SWEG]

How long did this take/ cost you?

[@mantasjuodkojis1443]

Great job. Stock camshafts are good choice for your desired power? What ecu you are planning to use?

[@JMSpeedshop]

Oem cams are.good for 5800rpms . It is a 5.0 v8 so i dont need high rpms to get to 700hp

[@JMSpeedshop]

Ecu is going to be a Maxx ecu

[@YourFloridaLand]

When you put the sealant on, you cut the video, so I could not see if you put sealant on every mating surface, even around the cylinder walls? Please advise, thanks.

[@JMSpeedshop]

Everywhere. But not around the cylinder bushings .

[@red05srt]

What was your final torque spec for the cylinder heads with the studs

[@JMSpeedshop]

On the studs i used it is 110nm

[@slavimaster]

Hi, i have m113 without ZAS on my w220 and want to change the valve steam seals, it is necessary to change the camshaft bridge bolts to a new one.

[@JMSpeedshop]

Every time the bearing bridge is removed you should renew the bolts. That is what the manual is saying

[@robertrobbins837]

Do anyone know the proper name you called the place that you take the timing with on this video the to place that you sit on the cylinder head to make sure that the timing is set right I'm trying to order them

[@JMSpeedshop]

i dont really know what you mean. i did not lock the timing

[@robertrobbins837]

@@JMSpeedshop timing alignment plates

[@azatzhansugirov162]

🙂👍

[@rafag1194]

Can i reuse the camshaft sprocket bolt or need new everytime its out? Ty sir

[@JMSpeedshop]

New

[@LaurenJoe-mf1mh]

Blood

[@selimcanavsar8702]

This build is awesome too but I am still salivating over V12 w201

[@JMSpeedshop]

Maybe a V12 after this build 😎