Making BIG GAME PCP 3500 PSI Valve and Tank for airgun

[@paulvanwyk9937]

Good stuff man😁👌

[@BernyAV]

Benjamin Marauder based?

[@pcpairgunschannel]

@@BernyAV yes I am copying the marauder design for a semi auto

[@BernyAV]

@@pcpairgunschannel Very nice. Hope you could do a video on how the semi auto function works.

[@pcpairgunschannel]

@@BernyAV kzbin.info/www/bejne/Y3TLmJSFicSAgJI check this video, it's not an explanation exactly though. I will probably make an explanation video with illustrations on how it works

[@BernyAV]

@@pcpairgunschannel Yes sir, I have watched this video and I must say, you do impressive work sir.

[@Brett_M]

The video just popped up for me🤔 I better turn on notifications!

[@benoitdudzik]

amazing like always !

[@adityasalunkhe1288]

wow pcp air gun boi back :0

[@MarouaneLM]

Gut gemacht 👍🏽

[@RJ-re4lj]

Very nice!!! Btw, try using PEEK instead of Delrin for the valve poppet next time. It’s harder to get a good seal (use the same method you do now) but you can crack the valve open much easier as PEEK doesn’t deform like Delrin against the seat, which also allows you to use a larger valve throat.

[@pcpairgunschannel]

So its easier to open? Sounds good!

[@RJ-re4lj]

@ yes, for the same amount of force from the hammer the PEEK valve will open more compared to Delrin (specially with higher pressures). I use around 80% of bore size for all ports, except the throat where the equivalent area (stem area - throat area) is about 90% of bore size. Anything above a .30 caliber it gets harder to open the valve (heavy hammer + heavy long spring), so I’ve been making balanced valves instead where you reduce the closing force on the poppet by having an internal “piston” exposed to outside pressure. It gets fun from there… there’s a lot of info online.

[@pcpairgunschannel]

@@RJ-re4lj I am actually planning a 80-100 ftlb .25cal. I will definitely use a balanced valve for that, otherwise it would need crazy hammer tension

[@sanepbodong1292]

Semakin bagus👍👍👍, sempat bingung lihat anda yang buat dari kuningan.

[@Canal-da-pesca]

Trabalho excelente

[@jbtharu515]

Please make a video making of 4500 psi air rifle tank

[@pcpairgunschannel]

maybe Higher pressure isn't always better but if you balance it it is fine.

[@markjonior]

Keren sekali, bagus sekali. Tapi mengapa Anda tidak menjelaskannya, seperti biasa, kami perlu menjelaskan detailnya agar manfaat penuh dapat diperoleh. Salam saya untuk Anda atas pekerjaan luar biasa Anda

[@Hunter_927]

👍👍👍👍

[@detoderos2027]

Hola que marca o que referencia de torno utilizas, gracias

[@pcpairgunschannel]

Vevor 7x16, the link is in the description

[@detoderos2027]

@pcpairgunschannel gracias,eres muy amable

[@Ben-f4s1x]

Hey man what Mill you use

[@pcpairgunschannel]

Bernardo KF 20 L

[@Ben-f4s1x]

@ oh wow i just orderd the Bernardo kf25D.Bernardo realy makes some good machines

[@robertkonarski7609]

👍👍👍👍👍👍👍👍👍👍 👏👏👏👏👏👏👏👏👏👏

[@ManoelSilva-nu6sj]

Is This cylinder not in danger of bursting?

[@pcpairgunschannel]

No, I calculated what it can withstand

[@triyosokumoro8313]

Mantap

[@USLUGHUNTER]

Why rotate spindle by hand for making thread

[@pcpairgunschannel]

I need slow speed, on A mini lathe low speed has too little torque And wont cut

[@USLUGHUNTER]

@pcpairgunschannel thank you for your information. Your design pcp seems like pcp in my country indonesia

[@pcpairgunschannel]

@@USLUGHUNTER Yes, I think there are many Mouser type air guns in indonesia. This is like the benjamin marauder

[@haichen7693]

用的钛金属管，还是不锈钢304管

[@gabrielurena608]

Se daño al final 😂😂😂

[@pcpairgunschannel]

no damage

[@gabrielurena608]

​@@pcpairgunschannel no quedó en 0 psi

[@MarouaneLM]

Wie lang ist die rohre ?

[@pcpairgunschannel]

60cm

[@MarouaneLM]

@pcpairgunschannel Und wie ist die länge von dem eingang der luft bis das druckventil ?

[@pcpairgunschannel]

@@MarouaneLM 41.5cm, 220cc

[@MarouaneLM]

@@pcpairgunschannel danke für die informationen 🙏🏽

[@MarouaneLM]

Noch eine frage : Ich machte eine, aber das Geräusch der Explosion ist laut. Deines Erachtens warum ?

[@prototype9030]

Full stenlis or duralumin

[@pcpairgunschannel]

Stainless, valve brass and aluminium

[@BernabeGarcia-f2g]

How to make to order with you sir that airgun valve and cylinder…

[@pcpairgunschannel]

Its not for sale, sorry

[@tillidie9832]

Can i buy ur item

[@pcpairgunschannel]

sorry, it's not for sale and i cannot ship it due to courier policies. it is just for entertainment

[@bayouflats5054]

Pretty slick. Why water? To “my mind”, now gotta get moisture out. Why not use nitrogen and getting any moisture out from atmosphere at same time. No finding fault, simple curious from my experience of “ things”. 😁🫵👍 Lathes are cool

[@pcpairgunschannel]

I had to fill it with water so that there is very little volume left for air. It's for hydrotesting, to see if the tank can withstand it. The water is easy to dry out, I had to disassemble it anyways for continuing the project.

[@bayouflats5054]

@ thanks for reply.

[@haichen7693]

漏水了吗，这个结构全靠密封圈承压，不会太可靠

[@pcpairgunschannel]

@@haichen7693 no leaking

[@willynilsen9302]

it`s normal to test with water because if the pipe burst it`s less energy. no ¨explotin¨, because u cannot compress water