I’m doing a RWD conversion on my 3rd Gen Prelude! This is gonna be a sick build. All the builds you guys do are top notch!
@Jeremeytickle274 жыл бұрын
That’s awesome. I’m putting a F20 out of a S2000 into mine.
@Jeremeytickle274 жыл бұрын
John Mitchell I’ve got a channel if you want to go check it out!
@slapdatcorn4 жыл бұрын
I'm subbed
@Nova_Ways4 жыл бұрын
Just a recommendation on the backside of the motor mount fish mouth piece drill a hole a bit bigger hole than the socket that fits the nut on the motor mount that slips in so you can tighten them up easier.
@mickeyandrade34354 жыл бұрын
Cali Ways - the nuts are plenty easy to access.
@sykko.exit23484 жыл бұрын
That's what I call BUILD. It's not just putting on blings str8 out of the box. Hell of a good job!
@gavnott45634 жыл бұрын
Victors editing is so awesome, yet another super talented guy in the throtl stables
@victordeleon84124 жыл бұрын
Thanks dude, I appreciate the comment 🤙
@briangapud4147 Жыл бұрын
This is the best video I’ve ever seen on KZbin. I was glued from the first 20 seconds on!
@red_dragonracingsilvereclipes4 жыл бұрын
fabbing out mounts can be a pain but when you get them the way you want them to be man it makes you smile since you done it yourself.
@mickeyandrade34354 жыл бұрын
pat finstad - Glad you understand.
@lancelaprarie61284 жыл бұрын
Nice work Mickey/Ricky. Good stuff as usual. Fabrication is fun.
@jtyoung7064 жыл бұрын
I freaking love this build so much!
@blakeschmid4 жыл бұрын
You guys should get check out steel-it ! Or really any weld through galvanizing spray for all the fab your doing, especially if you want it to last a while.
@mickeyandrade34354 жыл бұрын
blakeschmid - Thanks for the tip
@blakeschmid4 жыл бұрын
Mickey Andrade yea man of course! It’s a super sick coating, literally ground up stainless steel. Love the build! Makes me want to try and rwd swap my 1st gen civic wagon.
@aidanaltimas25764 жыл бұрын
Sort of see the stress on a str8 mount, but your second attempt, even made it look far sexier ✋ keep her lit boys 🇮🇪🍀
@PlzTouchSomeGrass4 жыл бұрын
Aidan Altimas I see a fellow Irish fan, from the land of shitty ecoboxes 🇮🇪🇮🇪🇮🇪
@slothgarage48462 жыл бұрын
Forget my comment on a previous video about the traction rods 😅 what is interesting with your EK is it appears to have EG/DC lower control arms, all the EKs I have seen have a one piece lower control arm and compliance arm, the EG/DC compliance arm being in 2 pieces allows you to run shims between them to get up to 3 degrees of extra caster, and EF/DAs run a traction bar and rods like you now have on the EK, which you qill be able to use to change the caster which is cool. One thing I am wondering is how you are going to change the rear toe settings now that you have custom trailing arms that have deleted the factory rear toe arms
@dontelatimore55874 жыл бұрын
I just wanna see who is going to finish first jimmy oaks or throtl
@dylanmounsey75154 жыл бұрын
Probably jimmy because there’s less involved
@fl0win.pr0se744 жыл бұрын
Apple's to oranges
@RR-cg2rq4 жыл бұрын
Gears and Gasoline
@mromagachi51944 жыл бұрын
elevator to latters
@Walter370z4 жыл бұрын
Can't wait to see the civic done! 🔥🔥
@branndon20864 жыл бұрын
Love all the Honda content, keep it coming please!!
@PANTYEATR14 жыл бұрын
Mickey here's a tech tip...you want to know what the best template material is? the cardboard from your cereal box, Eggos box, Rice-a-Roni box or anything similar. it's thinner and easier to cut than that stuff you were using. happy New year guys💪
@hannabishi04 жыл бұрын
Such strong yet creative hands.
@wldwst224 жыл бұрын
I love watching your skill in fabbing up solutions to the issues you run in to. Keep up the good work.
@chezrayrodney14804 жыл бұрын
Use the k-tuned thermostat swivel for the water neck it can be angled in multiple ways
@sanjuan2404 жыл бұрын
Was thinking the same thing about your first mount setup. Your build is kinda making me want to do the same thing one day but I’m thinking more of a rwd integra.
@melbgrk67254 жыл бұрын
awesome unique build and love the fab work guys :) Can't wait to see the finished product and see this car rip :)
@dailydriven18764 жыл бұрын
Hey I think skunk 2 make a thermostat housing that can help you out look into it LOVE THE BUILD THO ✊🏾✊🏾
@davehatzakorzian69944 жыл бұрын
The project is coming along awesome Mickey looking forward to see more on this build
@nlee61484 жыл бұрын
Those mounts are gonn flex
@everydayadventures37994 жыл бұрын
U should get the ktuned thermostat housing it rotates any way u want will help get around ur motor mount
@mickeyandrade34354 жыл бұрын
Manjit Kang - I have it
@jamesfcookjr4 жыл бұрын
Throtl ViP squad Good evening Mickey‘Rickie awesome more rear wheel drive Honda content you guys are putting in the work it’s going to be awesome 👍😊
@RunningSolo4 жыл бұрын
🙏
@cigarjefe4 жыл бұрын
May your 2020 bring you prosperity and success.
@Drawed_pengy0834 жыл бұрын
Notifs keep me updated on the build. Thank you!!
@MeSessum4 жыл бұрын
You sure the engine will slide out of the mounts now that there’s so much angle? Seems like it’s going to be stuck down in the narrower portion of the opening of both sides are in.
@megans69354 жыл бұрын
Paint match and wheel match with your other civic they would look amazing together
@CraigBrosRacing4 жыл бұрын
Hoonigan has 2 different k series mount that way in a s14 and 370z so in theory just watch how they did it and you can do the civic similarly. .
@mickeyandrade34354 жыл бұрын
CRAIG BROS RACING - With all due respect, I don’t need to watch them or anyone else to learn how to do this.
@CraigBrosRacing4 жыл бұрын
@@mickeyandrade3435 true..but all great engineers share there ideas so just figured you would like to see how someothers address certain problems when doing this swap not to "learn" how to do it...but to each his own ...bro your work is usually impressive so im sure this one will be the same..
@darylricamora10544 жыл бұрын
Shout out to throtl. Nice built.
@Jcosta72864 жыл бұрын
How are the mounts going to slide in and out with that much angle? I don’t get it.
@Pyhia4 жыл бұрын
actually looks really good holy
@AugmentedGravity4 жыл бұрын
1:37 Best episode of initial d. FOOOOREEEVEEEER
@rossneyman77814 жыл бұрын
Look at all that room for turbos
@madmadimadison75424 жыл бұрын
"...and girls". Thanks Mickey! Any other girls fascinated by this build? I'd love to do the same with my lil red EK, but with a Volvo T5 motor ;-) I love those things!
@BangBelt4 жыл бұрын
I'm not an expert, but the ears you cut off that tensioner are for an idler pulley you will need to run without the power steering pump. Might have to go center feed on the manifold.
@dutchnova34684 жыл бұрын
BANGwich electric steering
@BangBelt4 жыл бұрын
@@dutchnova3468 if you remove the power steering pump from a k series you have to run an idler pulley that attaches to the ears they cut off of the tensioner
@RunningSolo4 жыл бұрын
@@BangBelt I'm sure this is not going to stop us one bit .. we will figure something out if that is the case 🤷♂️
@mickeyandrade34354 жыл бұрын
Or, you run a shorter belt......... As I mentioned in the video.
@BangBelt4 жыл бұрын
@@mickeyandrade3435 it's not a length issue, it's a tension issue.
@t1mblumer4 жыл бұрын
So how is it supposed to slide in and out with both mounts canted back in opposite directions???
@abdulmuqsithassan30494 жыл бұрын
Make custom interior also for this build. Cant wait to see final result
@ShredGarage4 жыл бұрын
Now with the engine mounts at that angle, the whole easy slide in feature isn’t going to work.
@tbg4ming1264 жыл бұрын
Yeah like why wouldnt the mounts be good just standing straight? 🤔
@ShredGarage4 жыл бұрын
TBG4ming12 I get that part of it. Cause the other way puts the stress on the bolt, and not the rubber mount. But you could actually side the engine straight up. Now that the mounts are so vertical, you would have to slide left or right, and because they’re opposite, you just can’t slide them in, or out. So pointless.
@byrdb904 жыл бұрын
My thoughts exactly. Though, It’s a lot easier to criticize from the outside looking in. I will say, I appreciate all the hard work they’re putting in though and hopefully they’ll address this in a future episode.
@chickenfordinner20934 жыл бұрын
they should of went solid mount if they wanted the slide in brackets to work, lol they will figure it out next time they take engine out!
@tbg4ming1264 жыл бұрын
Yeah why didnt i thought of that.. It must have a meaning some how, i hope they address us
@natc53824 жыл бұрын
Nice build! Quick question, if your fish mouth engine mounts are at an angle on both sides, how will you be able to slide in or slide out the engine?
@RunningSolo4 жыл бұрын
So our first design worked that way .. but it wasn't functional... the motor mount will be working overtime to hold the engine up ... and also .. if the motor mounts brake or go bad there will be nothing holding the motor in place other than the subframe.... so by us changing the mounts to a 30deg not only will the supports will help the motor mounts but if they ever go out at least the mount holders will hold the engine in place .... as your question about sliding them in ... yes ... we have to slide them in first to the mount and then the engine block 🤷♂️ not the best results but is a better solution.
@natc53824 жыл бұрын
@@RunningSolo I got a response from Rickie!!! Nice work!
@stupringle33384 жыл бұрын
Loving this series, great build Do you have to get this set up certified to roll on the public roads over there or can you just modify as much as you want with not cert needed?
@mickeyandrade34354 жыл бұрын
Stu Pringle - No certs or warrant of fitness needed.
@ROthiporos4 жыл бұрын
nicely done guys.Although getting the motor out and not the transmition is probably impossible due to the design of the mounts ?
@mickeyandrade34354 жыл бұрын
Γιωργος Δελαμανης - Totally possible. Did it already.
@ROthiporos4 жыл бұрын
@@mickeyandrade3435 thanks for answering.Hope you noticed the question mark mickey as I was asking and not being a smart a s s .Love the content BTW
@chickenfordinner20934 жыл бұрын
definitely not the first mad scientist to fit a k like that in a ek!
@mickeyandrade34354 жыл бұрын
Please show us who has already done it.
@MartianRacing4 жыл бұрын
I did kzbin.info/www/bejne/gXqTnnV6abajp5o
@theidealone4 жыл бұрын
El Freddy did too.
@joshjones20534 жыл бұрын
Ktuned makes a cool swivel neck thermostat housing, I'm sure you knew!
@mickeyandrade34354 жыл бұрын
Josh Jones - Yup. Got one
@mateomorizio27774 жыл бұрын
Im excited for the end result its gunna be awesome :-)
@ilovetoyotatrucks4 жыл бұрын
Yall leave the top of the motor mounts open?
@nlee61484 жыл бұрын
They need more support on the side
@marlostewart11074 жыл бұрын
All I want for my ek hatch is pistons, rods, and a turbo. I'm feeling real basic right now... lol.
@geraldrogers94814 жыл бұрын
The build is awesome 👌 👌
@cormaclohenry5704 жыл бұрын
You guys should do an r-34 skyline
@primohernandez31394 жыл бұрын
639k subscribers? I don't get it this channel is dope they should have millions of subs!
@scenicviews10243 жыл бұрын
I've got an FC E Production open top race car I want to put a K24 in. What front cross member did you use.
@mrcow71954 жыл бұрын
I wish to learn on how they know so much bout engines and cars in general.
@afroman55314 жыл бұрын
Something I found out, you done learn, you EARN knowledge thru hard work and trail error
@hdm2992 жыл бұрын
How much would you charge to do a set a mounts like yours for the same block
@JoseJimenez-xz5yv2 жыл бұрын
Are you guys selling these mounts for a f20c into a 99 civic coupe
@Calvin_NL4 жыл бұрын
Great work team🤘
@Realtime15014 жыл бұрын
Lucimar racing on el Freddy did longitudinal mounted civics a while ago
@mickeyandrade34354 жыл бұрын
Realtime1501 - Sweet.
@Realtime15014 жыл бұрын
@@mickeyandrade3435 they were 1000+ hp cars lucimar racing still holds the rwd 4 cylinder Honda record at 6.68
@mickeyandrade34354 жыл бұрын
Did they do K20 into EK hatches?
@mickeyandrade34354 жыл бұрын
Lol. Bro, that’s a tube chassis drag car with a fiberglass body. We are using the factory unibody. Much different.
@MartianRacing4 жыл бұрын
El freddy, the Bully sport team, and me kzbin.info/www/bejne/gXqTnnV6abajp5o
@thenjmway4 жыл бұрын
I think Jimmy Oakes solution for the front suspension and rear for that matter is simpler as he is using both front and rear s13 subframes
@EasternSkvngr4 жыл бұрын
pretty sure he mentioned when he got the car that he knows thats an option but doesnt want to use S13 subframes and wanted everything custom
@RunningSolo4 жыл бұрын
@@EasternSkvngr correct 👍
@TheCrazymicki4 жыл бұрын
@4:11 nice thought
@mr.bolt_action56544 жыл бұрын
Do a golf mk2 next please
@superstreetking954 жыл бұрын
TJ hunts Adventador < Mickey's RWD EK CIVIC
@chipd42994 жыл бұрын
How about putting a K series into a late 80s/early 90s mini truck?
@mylespatrick25354 жыл бұрын
Hey ones you get everything on the engine are you going to tear the stuff off the engine and paint it
@kap63344 жыл бұрын
How long does it take you to get all of the metal shavings out of you heard?
@jessealba32484 жыл бұрын
Hardness mick.... hardness. Durometer is a tool 👍🏽
@Mattyyoung854 жыл бұрын
Not trying to be a dick by any means but gunmetal rwd civic it is an ek and was a kseries about 4yrs ago .. so your not the first but very quality build my brotha ... once thing I can tell you def build a oil pan with a baffle to stop oil slosh under launch .. it starve that motor for oil instantly .. keep up the good work my brotha
@bigjeff12914 жыл бұрын
Enjoy watching the progress and how you’re making it all come together through “creative fabrication”.
@alexjohnson14394 жыл бұрын
Can’t wait to see this finished!
@jeremyalvey42194 жыл бұрын
Mickey do yourself a favor and order the @Ktuned billet swivel thermostat housing. 💯
@mickeyandrade34354 жыл бұрын
Jeremy Alvey - Already have it
@BeyondABuild4 жыл бұрын
The swap for 2020 SEMA!! Let’s go!!
@MTNorville4 жыл бұрын
I say we start all start a swear jar to fund getting Ricky a damn mask with his name engraved on it xD
@elminime14 жыл бұрын
So are you guys using a k series or the F series from the S2K? Well ether way car is gonna be a beast for sure.
@jeremyalvey42194 жыл бұрын
MS3T GEN2 K swap F trans
@elminime14 жыл бұрын
So is a k better than an f series and why?
@lewischafer33334 жыл бұрын
I Really in enjoyed watching the Amazing Vlogs ever
@mromagachi51944 жыл бұрын
fknnnnn love it man
@OtotheGHTX4 жыл бұрын
Whip out the torch for the cuts.
@mickeyandrade34354 жыл бұрын
oscar gonzalez - We don’t have one.
@colegerz24504 жыл бұрын
Pfi speed has a video of a rwd hatch too not sure if it was a k series tho
@MartianRacing4 жыл бұрын
Not a hatch, but good memory. kzbin.info/www/bejne/gXqTnnV6abajp5o
@amarularif31104 жыл бұрын
Im gonna tell my kids this is Hagerty Rebuild
@Taktko4 жыл бұрын
This is what the civic should have been. I could have liked them.
@gito...80683 жыл бұрын
Where is your shop?
@oscarbarahona1664 жыл бұрын
Amazing!
@doubleg27534 жыл бұрын
Jimmy O!!!!!
@griffith76514 жыл бұрын
YOO IM LITERALLY WATCHING INITIAL D RN 🤣🤣🤣🤣🤣
@Overload1804 жыл бұрын
thank you for not throwing up the 6s every 5 mins
@erikhagelin63744 жыл бұрын
Skills👍
@esaulpr554 жыл бұрын
What about the Nissan 350t
@timm59704 жыл бұрын
what transmission is being used? Is the a plate used to mate it to the trans?
@mickeyandrade34354 жыл бұрын
tim m - F20C trans with JSP trans adaptor
@timm59704 жыл бұрын
@@mickeyandrade3435 you know if H/F series FWD engines can directly mount to the f20c/f22c transmissions?
@mickeyandrade34354 жыл бұрын
tim m - Pretty sure they do not.
@timm59704 жыл бұрын
@@mickeyandrade3435 Which makes no sense. F/H engines and transmissions are all universal. If the "F"20c and "f"22c do not share the same designs why are they labeled with the "F series" moniker? Silly Honda
@ddevil49804 жыл бұрын
Lol yeah it takes around 60 tons with the right tooling to bend 3/16 steel.
@dd___dc4 жыл бұрын
Whatz up with da ice cream truck
@shredtheknoll33574 жыл бұрын
Sick!!!
@dylanmounsey75154 жыл бұрын
Nobody: Mickey: Magikarp...karp...karp 😆
@6erronjx4 жыл бұрын
Wait this will be drag racing civic or track?
@afroman55314 жыл бұрын
It's something for them to have fun with, track, street, ect.. they built a sick build but gave it away before they could rip it, and that made them sad... I can understand why
@Rezzinage4 жыл бұрын
dope!!!
@austinking224 жыл бұрын
Dope
@MrPryor164 жыл бұрын
Jimmy oakes is doing a similar build
@trianifeA7x3 жыл бұрын
I'ma just let y'all know. There's plenty of room there for a pushrod v8 👀😆
@BENKS-THEKID2 жыл бұрын
I'm watching all the video until I see everything done
@alexpichardo59774 жыл бұрын
Will you guys be interested in making the mounts again if I pay you.
@justiceofthesun73034 жыл бұрын
Not the first ever.. K has been around for a while.. Do you really think you're the first to rwd an ek??
@woodlandscrew-pa85684 жыл бұрын
All that metal is getting painted right?
@mickeyandrade34354 жыл бұрын
Woodlands Crew - PA - Powdercoated
@woodlandscrew-pa85684 жыл бұрын
@@mickeyandrade3435 ahh even better. Really really excited to see this finished product.