MAXXFORCE 13 DELETE. EMISSIONS REMOVAL

maxxforce 13 egr removal and dpf removal
www.vppartsunlimited.com/prod...
s1partscenter.com/?gclid=CjwK...

[@titomedellin624]

Thanks again for this video it was very very helpful! I just finished up the delete on my day cab which went very smooth and it was all thanks to this video. Unfortunately I did not have the time to ship my computer or wait for parts from VP unlimited so I had someone local reprogram the computer and I made my own block off plates. And just yesterday I tore apart my other truck to do the delete on that one as well.

[@jadatransportation347]

Thanks for a great well explained video! Very helpful!

[@neilcockrell3252]

this video has helped tremendously with our delete using same programmers and delete kit you used thanks!

[@alecburril3433]

I'm happy it helped you out. Let me know how you like it after you run some miles

[@DSKdanny]

Great video, helps a lot!

[@kymachen381]

My butterfly valves were broken inside the EGR valve on the back (hot side) of the EGR. I found all but 1 piece of them. They beat up the tubes of the EGR and coolant was leaking back into the exhaust. I tried to grind the beat up tubes down some so the block plate would sit flat. I did the best I could and was a little surprised that it didn't leak afterwards. I was lucky because the exhaust manifolds on this truck were not solid. They both had the flexible braided steel couplings on them which allowed me to install the thin blocking plates in them without removing them. I could not get the bolts removed from one of the exhaust manifolds, (the far back one) so i installed it at the front of the EGR valve. I left all of the components installed. I was only able to do this because of the flexible manifolds. All of the coolant lines were left installed as well. The front side block plates were pretty easy though. When the valves broke on this truck the electric motor that controls them was stuck on and the wires that power it were fried all the way back to the wiring harness and some other wires were burnt. Someone was lucky this truck did not burn to the ground. I sure wish I would have found that one lost piece of butterfly valve.

[@jbtrading1116]

Awesome work bud!

[@aaronpeddicord2944]

Very well done sir!!!

[@topquality9949]

Thank you for informative video(respect)

[@alecburril3433]

You're welcome

[@midnight873]

Amazing video, any chance you can post the link for the exhaust you got on amazon?

[@honda110wave2]

nghe tiếng turbo tăng áp của dòng máy maxxforce n13 hay lắm

[@dustinma6466]

The truck I bought already has a dpf delete and tune but they didn't do the egr. Should I still go get it tuned after I plate off the egr or do you think its good for now?

[@thomashall6878]

Hi Alec. Thanks for the video! I just purchased a low miles 2013 prostar. I would love your help. I live next door in Spirit Lake.

[@alecburril3433]

@thomashall6878 its pulling season but I'll help if I can

[@nervillerih-reh6824]

You're awesome. That thing will run for ever once it stands

[@alecburril3433]

No. Still several issues with the maxxforce engine it's self. Was never built to last. Made it to 909k miles before shitting the bed. But hey it was a 10k truck that made me a ton of money.

[@robstuckey]

​@@alecburril3433 ah yes, shitting the bed, a technical term in which the engine is no more, nada, zip, it just disappears out of your truck, impossible to fix. what in your opinion are the issues with deleted maxxforce engines Alec? You have gotten probably 50 questions on how your engine did post delete, maybe you can update folks with terms other than just, it shat the bed, which provides zero information

[@alecburril3433]

@@robstuckey there is an update video posted.

[@robstuckey]

@@alecburril3433 the update video is prior to your engine "shitting the bed"

[@robstuckey]

@@alecburril3433 but thanks anyways for answering zero of my questions

[@jahmarkx6307]

Great information

[@JH-tl8xj]

Where is the ECU located in a 2012 International ProStar? I am going to follow your advice and send it to Abbotsford BC. Thank you in advance. JH

[@253FreakCar]

Looking to buy Maxxforce and delete right away how is it running after? Pulls strong ? No more random check lights ?

[@popsshop6349]

I just got a prostar that runs fine but looses coolant after 100 miles through the exauhst. So I’m going to block the cooler off. I noticed you dealt with your manifold. Is that because yours was just cracked? So i don’t have to do the manifold part if I’m just blocking it off? Ecm has to be tuned to run it after the block off ?? My truck doesn’t have def from manufacture idk if that matters.

[@alecburril3433]

The maxxforce didn't come with def just the N13 and A26. Yes the manifold was replaced because it was cracked. Remove the egr valve and cap both sides of the egr cooler and have the ecm tuned. That truck will treat you good 👍🏻

[@nyahsanchez9878]

Do I have to remove the egr cooler core? Or can I just put the plate where the egr valve goes and that will seal it?

[@bhicks2136]

Alec thx for the helpful video and the nugget on v p parts but where did you send the ECM to get reprogram ?

[@alecburril3433]

Sorry I didn't mention that. I used 3k calibrations in Abbotsford BC. Cost with shipping was $2100 US🇺🇸

[@bhicks2136]

@@alecburril3433 Thx a lot my friend.

[@rayturner2823]

@@alecburril3433 where you got ecm program at again i got the block place already man you been big help keep up the go work

[@alecburril3433]

@@rayturner2823 glad the video was helpful. I used 3k calibrations in Abbotsford BC. Took a week with shipping both ways

[@bhicks2136]

@@alecburril3433 I sent my ecm to 3k and got deleted and tune and I'm expecting it back tomorrow. All I have left to do is to install the block plates. I really couldn't trust anyone to do this delete because people don't really honorand stand behind their work. And 3k made sure that I knew the ecm tune has a lifetime warranty. ALEC YOU ARE THE MAN !!! I'm sending you a big high five for that video and the info...

[@maltesefuller7507]

I'm confused on what your saying to do with the coolant line in the front after removing the hard tube section and running it back to the radiator reservoir. Could you explain in detail. Thanks

[@alecburril3433]

I will try. The fitting on the front of the egr cooler, that line runs to the egr valve. Then another line is the return from the egr valve to the coolant reservoir. So when you remove the egr valve there is no need for that line. So just go from the fitting on the egr cooler straight to the reservoir. If you still can't figure it out send me an email and I will make a video of it and send it to you. [e-mail]

[@willrivera5544]

Is been a while since you did all the changes on your truck ! My ? To you is how’s everything working out so far ?

[@alecburril3433]

Everything is working very well. Pulls strong.

[@jerrygreen4834]

Thank you for the video, do I even need the EGR cooler system?

[@alecburril3433]

It's pretty difficult to remove considering the heater hoses and coolant manifold at the back of the engine. If you cap both sides it becomes nothing more than an extra coolant tank.

[@rylonpeterson2254]

When you did your delete did you have to unplug anything??

[@jamesharris-nn5gt]

Hey on the block plates where did u get them.do u have to remove the low temp cooler thanks james

[@alecburril3433]

Vip parts unlimited No the coolers are still in place

[@firstdaywithnewbrain2504]

Hey Alec I’m about to start this procedure today. Would it be ok if I reach out to you if I get in a bind? Your video is pretty clear but I’m just not sure about the larger metal coolant line at the back of the engine. I’m going to watch your video again (3rd time). Maybe I missed something. Thanks.

[@alecburril3433]

Yes either here or find me on Facebook. I'm in most of the maxxforce and international pages. If you don't have a leak with that large manifold at the rear of the engine do not take it off

[@jasonfuentes7027]

@@alecburril3433 my 2012 pro star day cab went down about a year and a half ago due to turbo failure. I’m about to get started on replacing them both and deal with a broken bolt at the egr valve. It seems to be the ideal time to do this. To remove the egr valve do I need to remove the coolant pipe in front of the valve?

[@alecburril3433]

@@jasonfuentes7027 no removing that coolant manifold is not necessary

[@davidherrera1503]

I have a 2017 international maxxforce I had deleted years ago, been running solid ever since. Til yesterday I ended my day went to park the truck and turn it off, put key in off n position but the engine stayed on.. any ideas?

[@firstdaywithnewbrain2504]

@@davidherrera1503 I would say most likely is a bad ignition switch.

[@Patriotoneable]

Alex, with this delete method the EGR cooler cores need to stay intact and still circulate coolant right? Is there a way to completely bypass the EGR cooler cores? Mine are busted due to turbo and exhaust back pressure from a hack job mechanic not understanding how to delete the Maxforce 13

[@alecburril3433]

Leave the cores intact and cap both ends of the cooler and don't worry about it anymore

[@josepina108]

Alec question once you get all this stuff removed how you go about emissions Do you get more power ? How about mileage? I herd some people get overheating problems thank you great video keep up the great work

[@alecburril3433]

If you remove everything and use a reputable tuner you won't have those problems. If you use a hack job you will have all kinds of problems. Had the power set at 515/1850 and it pulls very well. Mileage varies with load and speed.

[@user-ln7of9gs4s]

@@alecburril3433 post your fuel economy.

[@alecburril3433]

@@user-ln7of9gs4s maxxforce don't get good fuel economy

[@user-ln7of9gs4s]

@@alecburril3433 I wish you’d just give numbers, that doesn’t help anyone. I appreciate the vids and taking time to reply, but people would Iike numbers. I can tell you first hand I drove one of these that was always trying to Regen, and was getting 3.5 mpg on the highway at 65 mph in a day cab and a 48’ reefer.

[@alecburril3433]

@@user-ln7of9gs4s lol numbers depend on the driver, speed, part of the country, Load. It's not a one size fits all answer. 3.5 is terrible but this truck never got over 6. But I had enough power to make it somewhat ok

[@brandonalean1594]

Does it have jakes? 😂 I’m looking into buy a truck soon. I kinda want to chance these! Cheap as all hell even with this inflation💀

[@alecburril3433]

Yes the 2010 and newer have a good Jake. The earlier ones only have an exhaust brake. Take a chance. Don't be scared

[@antoniomiles2973]

Doing the EGR deletion will that stop you from leasing your truck under a company ? What are your thoughts ? Amazing video as well thank you!

[@alecburril3433]

Most companies don't care. I have my own authority, so it was not an issue

[@antoniomiles2973]

Regardless of authority, having your own equipment deleted , will companies even check this type of stuff when you’re leasing on? Is there anyway to delete and hide it with new stock parts ?

[@alecburril3433]

@antoniomiles2973 you're not understanding. If you have your own authority, you don't lease on to another company. If you just own the truck each company will be different. If they plug into the ecm it is obvious if it's deleted or not

[@antoniomiles2973]

I was going to get my own authority and let it mature while leased on somewhere, what are your thoughts on that ? Smart or not ?

[@alecburril3433]

@antoniomiles2973 I don't see any reason to do that. The 1st 90 days can be rough, and then the doors start opening up. You have to carry insurance anyway for it "season" so you'll be paying double the Insurance. If you're gonna do just jump in and go. Call the shots and make the moves. I run Monday to Friday on an average of 1800 miles a week with $5300 gross and $3450 net. With the state of the economy I say that's pretty good. It al depends if you wanna be an entrepreneur or not

[@justinkolb4628]

Which forums do you recommend for info? Going to be doing this to a maxxforce 9 soon

[@alecburril3433]

Mhhauto.com is a great resource as well as 3 Facebook groups dedicated to the maxxforce will be a great help as well

[@titomedellin624]

Thinking of doing this to mine but just wanted to run an idea by you first. What if I leave everything in place and place 2 block plates at the egr valve? Is this the same as removing everything and placing 3 plates?

[@alecburril3433]

I'm not a fan of leaving the stuff in place. You can't see the egr valve from under the hood anyways. Just my take on it. If you're gonna delete it the dumpster is where the stuff should go

[@titomedellin624]

Thanks. I cleaned battery cables and the egr fault along with de rating cleared.

[@alecburril3433]

@@titomedellin624 good deal. Cleaning and checking your grounds is also a good yearly maintenance idea

[@avenged06x]

On the drivers side of the engine you show two lines that you said you modified exhaust block off plates. @2:47 is that needed to be modified? Deleting this truck for a friend and not currently near the truck.

[@avenged06x]

Also, did you crack all the bolts loose with a 1/2 impact or by hand?

[@alecburril3433]

@avenged06x yes the 2 lines you are talking about are where the exhaust exits the egr cooler and goes into the intake manifold. The reason you block those is either the egr cooler is already leaking or when it does leak the coolant can't get into the intake. Essentially makes the egr cooler and coolant tank and prevents harm to the engine. I used heat and broke all bolts loose by hand

[@avenged06x]

Hey Alec, appreciate your response. I've called the dealer and they claim this is the Maxxforce 13. My EGR valve appears to only be 6 bolts. Yours appears to be 8. Am I missing something here? Can I email you a picture?

[@alecburril3433]

@avenged06x it's an 07 epa version. Basically the 1st round of advance emission controls. [e-mail] is you have anymore questions. KZbin is slow with notifications

[@TheTaqwaProduction]

Did you use copper exhaust sealant on all gaskets? Do you know what is proper torque for exhaust manifold bolts engine side and where block of plates go?

[@alecburril3433]

No sealant, manifold bolts to the head are one time use. 25 ftlbs then 90 degrees. Block off plates are just good and tight

[@TheTaqwaProduction]

@@alecburril3433 I guess I wanted to say did you use copper gasket maker, I see some orange stuff in the video where gaskets are. Is that copper gasket maker or what?

[@jamesharris-nn5gt]

Can u get all the block plates for the maxxforce from source 1 and also what tunning on the ecm did u have horsepower and torque settings

[@alecburril3433]

I don't know about source one. 3k calibrations took care of the tuning. 515/1850

[@franciscoduartegonzalez8737]

Hi Good afternoon ! Did you drain all the coolent or just the coolent from the reservoir?

[@alecburril3433]

The whole system

[@franciscoduartegonzalez8737]

@@alecburril3433 thanks 👍👍👍👍

[@jeancaraballo7506]

I run alot to west Virginia and Tennessee and I loose alot of power going up those big hill will this help with the power lost?

[@alecburril3433]

Yes assuming your turbos and fuel pump are in good shape

[@brandonfehr3190]

Hey sir if there is a way to message me direct. I’d like to see where I can get the ECM tuned. Thanks

[@gabrieldaly6771]

Do we need to use the gaskets on the exhaust manifold or will the block off plate alone be enough?

[@alecburril3433]

Use the gaskets and then I cut the flanges off of the manifold to egr valve pipes because the pressure will warp the plates and blow out the gaskets

[@gabrieldaly6771]

@@alecburril3433 thank you sir

[@Patriotoneable]

They seem like a bargain because they are so cheap, however there is no deal to be had even if the the truck is free. It may be difficult to get into the green running a Maxforce 13

[@alecburril3433]

It's easy if you can do the work.

[@Patriotoneable]

@@alecburril3433 I know, I did it all. I liked the way the truck feels and runs, but it’s just to keep the darn thing running problem free. They sure designed an expensive POS to say the least. I can honestly say that I have become a Prostar /Maxforce 13 mechanic against my will lol.

[@littelcarter]

DOT ever mess with you? Thinking about doing mine.

[@alecburril3433]

DOT doesn't care about emissions in most places. Passed 2 level 1 inspections after delete was done

[@TopFlightGarage]

How well is it holding up? Any problems since?

[@alecburril3433]

She is a pulling machine.

[@kingspencefitness6127]

Before the delete were u losing coolant and was oil goin in to the resovior

[@alecburril3433]

Yes I was using coolant, no issue with the oil in the reservoir

[@TheMonkapotamus]

What do you do about cooler? Pull out? Grind off little alignment button?

[@alecburril3433]

Cooler is all intact just capped on both sides

[@kymachen381]

That’s my question. Do you have to grind if the buttons or do they recess when the plate is pressed on?

[@alecburril3433]

I didn't grind them off

[@TheMonkapotamus]

@@kymachen381 they recess. I just tapped them lightly with a hammer till they laid flat.

[@kymachen381]

I didn't either but i think I should have. I have only ran the truck a little but it is not leaking at all. When I got to this point I was exhausted and it was getting dark.

[@franciscoduartegonzalez8737]

Hey how's your truck running with the delete? Can you give us an update please?

[@alecburril3433]

I'll make an update video tomorrow and post it up

[@alecburril3433]

Video is up

[@juangomez8186]

Hello sir nice video I’m trying to delete my maxxforce dt if possible just drill out the dpf and the doc or is better to install a straight pipe? Because in this box truck the dpf is visible

[@alecburril3433]

Either way is fine

[@juangomez8186]

@@alecburril3433 ok and do you know where I can buy the parts for block the egr or I have to make my own parts?

[@alecburril3433]

@@juangomez8186 you'll probably have to make your own for that engine

[@juangomez8186]

@@alecburril3433 ok than you

[@xl_shots_3970]

My maxxforce13 egr delete was done before I bought it. but I can’t get the lights to turn off on the dash. What’s your take on it?

[@alecburril3433]

What lights are on?

[@xl_shots_3970]

Abs, traction control, transmission, and the engine and air pressure, fuel and voltage gauges work sporadically. Also when those lights are on the engine brake is always on. The last mechanic said there wastegate fault of some sort and cruise doesn’t work but will high idle in park

[@alecburril3433]

@@xl_shots_3970 I don't think that is anything to do with the delete tuning. Sounds like a fault with the body control module and abs moduel.

[@xl_shots_3970]

@@alecburril3433 body control module has been replaced and it reads abs module and electrical fault on the dash as well.

[@gjgarrett22]

@@xl_shots_3970 Did you figure why your lights were on after the deletion? Having the same issue.

[@user-te5rb1pu7q]

What’s the name of the Orange sealer with the plates?

[@alecburril3433]

High temp rtv

[@Vector100]

How can I contact the shop where the ECM was shipped to be tuned up?

[@alecburril3433]

Call or email them

[@leons9062]

is it passible to take whole egr cooler out and drive without it?

[@sstevocamaro]

Yes, but it looks very tacky. I’ve seen people use pcv pipe lol. You definitely won’t pass a visual check

[@Mo-hh4kd]

What was your total cost, at the time of the video, for the delete?

[@alecburril3433]

$3500 USD. For everything I did

[@Mo-hh4kd]

@@alecburril3433 that seems like a good trade off, I’m thinking of doing it to my 2018

[@thomashall6878]

Who did you send the ECM to for tuning?

[@alecburril3433]

@@thomashall6878 3k calibrations

[@eaglesteamtransport9375]

I did delete mine in Marion IN, a place called "pocket" something. They did literally a horrible job. My truck used to be super awesome, but I was inexperienced and deleted it by thinking that this will prevent bad things to come. Anyway, after a year truck died completely and throughout a year it kept constantly losing power and finally it wont run over 30-35mph!!! I loved that truck so much and after 4 yrs still I havent sold it, it still sitting in the yard and I am paying parking for it. I dont know even where to take it and check it out, since dealerships wont deal with deleted emission trucks. One more thing to specify is that I did change the oil right before it died, and after 400 miles the oil got so thick and dark black colored, any idea anybody what this might have cause this ? Good luck to everybody deleting them, but I am just so afraid doing it again. Peace out there ✌️🤘

[@davidreyes2298]

Have you installed a tuner for it?

[@eaglesteamtransport9375]

Not really sure about it, but most likely no. They did a terrible job unfortunately

[@eddiekendall4269]

I had a emission delete and and now my is running a high temp any suggestions on what has happened

[@MrEuroWolfie]

@ eddie kendall ..i threw my thermostat away a long time ago, after all its a work truck so shouldnt look at economy..its silly in my books..and these engines have many ways of overheating, egr,fan clutch issues,radiator issues,dpf if equipped, and thermostat loves messing up on these also..too many chances to have a headache..now it takes forever to warm up winter time,must use cardboard in grille,but no more issues ,..ps ,thermostat keeps fluctuating pressure in the system and these weak in egr cooler blow through, or just easier to find a weak head gasket spot,etc... no harm to engine ,all the people say things but really its still warm engine not stone cold..just cooler..2005 dt466 egr..my truck..

[@tbonepatti]

How come I can't see any of your replies?

[@aaronpeddicord2944]

I did my delete and the guy only put a stopper in the flex hose he didn't move no fuel lines or coolant lines what do you think he was a international tech for 15 years

[@alecburril3433]

My theory is the parts cannot be a problem if they are not there

[@aaronpeddicord2944]

@@alecburril3433 if I take off the EGR supply line and cap it, there will be no coolant in the EGR or down to the doser valve correct? If so do you happen to know which one is the EGR supply line

[@gregcoulouris9349]

Can you please get me part numbers for the plate kits,and where I can send the ecm

[@alecburril3433]

The link for the plates is in the description. 3k calibrations for the ecm work

[@Bighodge721]

Where did u send ur ecu and what all did they do to it ?

[@Bighodge721]

And the price

[@alecburril3433]

3K calibrations in Abbotsford BC. Tuning and over night shipping both ways was $2100 🇺🇸

[@jfray3725]

I worked for a guy that loved these trucks. I hated them, no balls in the engines

[@alecburril3433]

Once tuned and deleted they pull as good as any other modern truck. Stock they won't get out of there own way

[@andyescobarescobar]

Any idea how to fix the code spn 731 fmi16 Engine shuts down thinking acceleration is too much

[@alecburril3433]

Any other codes? Generally an over fuel condition but need the rest of the codes to help

[@andyescobarescobar]

@@alecburril3433 It had an issue wher engine ran with only 3 injectors and i swapped 3 inejectors 123 and it then got this issue

[@merives2263]

Can I put a series 60 turbo on a maxxforce 13?

[@alecburril3433]

Yes. Tuning will be your issue. The adapter is reasonably priced

[@carltonwilliams8653]

How do you reprogram the ecm with no dpf stuff?

[@alecburril3433]

Send it out and have it done by a reputable tuner

[@haydenkapiko3191]

Do the two 2 bolt flange coolant lines on the front need to be blocked off?

[@alecburril3433]

Coolant lines? The lines on front of the egr cooler to the intake? Those take the exhaust back into the engine. Yes block those off

[@haydenkapiko3191]

@@alecburril3433 any way i could email you? i have a few questions regarding the delete and tune. Im having some problems with my delete as in a shit load of smoke...rolling coal everywhere i go.

[@haydenkapiko3191]

Hell I’d be willing to buy that ecm from you if you’d sell it.

[@alecburril3433]

@haydenkapiko3191 that was the first thing that sold.

[@haydenkapiko3191]

@@alecburril3433 makes sense lol. Where you located? I’m in the Spokane area

[@eg5175]

Are you in Seattle..?

[@alecburril3433]

East side of the state

[@eg5175]

Can you do mine? I pay

[@alecburril3433]

I could in a few months. I'd need the truck for a week to 10 days. $6500

[@eg5175]

Hi, i been charged by local mechanics for egr delete twice. One mechanic put plates at front of egr cooler but not as shown by you in video. They charge me for programming my ecu. Still loosing power and boost after driving like 10 mins

[@brandonfehr3190]

I’m having that same issue but truck isn’t deleted. They think nuts injection pump

[@WorldGeniusIntel]

Anybody knows what happens if you delete the truck without getting it tuned?

[@alecburril3433]

It will derate

[@Delmarosalinda1]

I see the delete is for 2012 or older. How about 2016?

[@alecburril3433]

3k has the tuning for the N13. You'll have to make you own plates I believe. Still doable

[@Cracker0309]

How long did it take to get the block off plates from VP Parts?

[@alecburril3433]

5-6 days

[@Cracker0309]

@@alecburril3433 I ordered the plates on Monday and received them today. Sent my ECM to 3K Calibrations on Tuesday and I'll be in tomorrow. Can't wait... What did you do to break loose the egr valve from the cooler?

[@alecburril3433]

@@Cracker0309 make sure you got the bolts from the front side that thread into the valve, then a pry bar through the valve and work it up and down and it'll come loose. Let me know how you like it when it's all done

[@Cracker0309]

@@alecburril3433 I finally got the install finished a couple day's ago. I drove it for the first time yesterday. I noticed a few things that concern me. One thing is when I take off or even rev it up parked, it'll start to miss a little and doesn't have that much power. The other is my oil pressure. At idle is around 20 psi but when driving it stays around 80psi +. I'm not sure if this will effect anything but i'm thinking that maybe I have a sensor either still plugged in from the egr cooler or one not plugged in. I do have the EGRT sensor still plugged into the EGR module cover that's next to the EGR outlet tubes in the front. I also have everything unplugged that goes to the DPF filter. As far as my exhaust goes, I removed the DPF filter, gutted out the DOC and installed the down pipe to the DOC to make it look like I still have the DPF filter installed. Any suggestions would be highly appreciated.

[@alecburril3433]

@@Cracker0309 check engine light? Any soft codes in the ecm

[@stevedonaldson4316]

Well my name is Steve Donaldson I got a Lone Star 2013 with a match for 13 minute I'm trying to delete it now I had number one Turbo go out on me couldn't buy number 2 so I had to put it back together I had APC R deleted deleted not for sure what all I got to do if I got to take anything else off the engine beside the exhaust I would watch your video I didn't know if I have to get in that cooler or not that's what I got left to do right now is Take the mufflers they're apart or just put straight against on it McDonald's on it I would appreciate if you could get back with me and let me know if I need to do anything else to delete things They built the 1st Lone Star for me to drive across the country if you would like to look at that it's called driven deliver

[@daMillenialTrucker]

Could I bring my truck to you and you do it and I pay you? How much would it cost you for your time?

[@alecburril3433]

$8,000 parts, labor, and tuning. If you're serious let me know and we can work out the details

[@brittanyfoster3579]

How can I get a hold of you I have some ?'s

[@alecburril3433]

Email works. [e-mail]

[@vietle9236]

i am vietnamese, this problem is not good. overheating. oil loss. engine weakness. related to ecm

[@richardmunoz9685]

Where can I send my ecm

[@alecburril3433]

I sent mine to 3k calibrations in Abbotsford BC

[@eg5175]

Hi are you avialable to do mine

[@alecburril3433]

Yes. I charge $8,000

[@jahmarkx6307]

Hey brother can u delete mines

[@alecburril3433]

I can do the work. The ecm has to be sent out for programming

[@blakebreckenridge]

I've heard the Maxxforce 13 is a good engine once it's deleted.

[@alecburril3433]

It's fair. It'll last as long as any other modern engine

[@user-te5rb1pu7q]

What’s the name of the Orange sealer with the plates?

[@sstevocamaro]

It’s a copper sealant. Good for high temperature